JBC CA-9QF Manual Feed Soldering Station Instruction Manual

JBC CA-9QF Manual Feed Soldering Station

Product Information

The Manual-Feed Soldering Station is a soldering tool that comes in different voltage options: CA-9QF (100V), CA-1QF (120V), and CA-2QF (230V). It includes various components such as an adjustable tool holder, cartridge holder, tip aligner display, adjustable cable collector, tip cleaner with antisplash membrane (brass wool inside), wiper, AP250 Manual-Feed Soldering Iron, main switch, fuse power socket, equipotential connector, earth fuse, USB-B connector, and fume extractor connector.

Packing List

• Manual-Feed Soldering Station – 1 unit
• Power Cord – 1 unit (Ref. 00023715 for 120V, Ref. 00023714 for 230V, Ref. 00025092 for 100V)
• Brass Wool – 1 unit (Ref. CL6210)
• Sponge – 1 unit (Ref. S0354)

Packing List

The following items are included:

Features and Connections

Adjust. Tool Holder
The position of the tool holder (ref. 0014706) can be easily adjusted by loosening or tightening the knob.

Adjustable Cable Collector
The cable collector (ref. CC1001) keeps the cable away from the work area and prevents the weight of the cable from disturbing the operator while soldering .

Tip Cleaner

Select the option to suit your needs and improve the thermal transfer of the tip.

Wool/Brush Replacement

1. Unlock the splashguard.
2. Lift off the splashguard and change the worn brass wool/brush for a new one.

More cleaning options:

Changing Cartridges

To change a catridge safely, unplug the tool or turn off the station before following these guidelines.

1. Removing
2. Inserting
3. Aligning
4. Fixing

Compatible Cartridges
The CA stations work with C250 cartridges and AP250 Solder Feed Irons. Find the model that best suits your soldering needs in www.jbctools.com.

Replacing Solder Wire

1. Removing
2. Replacing
3. Inserting

Changing Feeder Nozzle

Unplug the tool or turn off the station before following these guidelines:

1. Unscrew the rear screw, than remove the reel and the solder wire from the nozzle.
2. Unscrew the two screws on the other side of the solder feeder.
3. Remove the srews and lift off the cover.
4. Take out the feeder nozzle and replace it with the new one while holding the three components (trigger, slider and lever), identified in the picture, in place. Reassemble the cover and tighten the three screws.
   Note: Do not disassemble these 3 components. It is imperative to hold them in its place.

Regulating Feeder Nozzle

1. Depending on the cartridge used and the component to be soldered, you can vary the feeder nozzle length up to 10mm.
2. Adjust the feeder nozzle length and thighten the screw.

Operation

JBC’s Most Efficient Soldering System
This revolutionary technology is able to recover tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, tip life is five times longer than with other brands.

Control Process

Work Display

Menu Display

Troubleshooting
Station troubleshooting available on the product page at www.jbctools.com

Parameters

Be careful when using these parameters as they may reduce the tip life if not used properly. Please follow the recommended guidelines:

Station Settings

Tool Settings

USB Connector

Download the latest software from our website to improve your soldering station.

JBC Updater
www.jbctools.com/software.html
Update the station software via USB connection:

Maintenance

Before carrying out maintenance, always switch the device off and disconnect it from the mains. Allow the equipment to cool down.

• Clean the station display with a glass cleaner or a damp cloth.
• Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
• Periodically check that the metal parts of the tool and the tool holder are clean so that the station can detect the tool’s status.
• Maintain the tip surface clean and tinned before storage to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
• Periodically check all cables.
• Replace any defective or damaged pieces. Only use original JBC spare parts.
• Repairs should only be performed by a JBC-authorized technical service.
• When this warning appears on the main display, the earthing fuse must be replaced.
• Replace a blown fuse as follows (applies to both the earthing fuse and the main fuse):
  1. Pull off the fuse holder and remove the fuse. If necessary, use a tool to lever it off.
  2. Insert the new fuse into the fuse holder and return it to the station.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

• Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
• The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
• Do not work on electrically live parts.
• The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
• Do not leave the appliance unattended when it is on.
• Do not cover the ventilation grills. Heat can cause inflammable products to ignite.
• Avoid flux coming into contact with skin or eyes to prevent irritation.
• Be careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Utmost care must be taken with liquid tin waste which can cause burns.
• This appliance can be used by children over the age of eight and also people with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.

Specifications

CA
Manual-Feed Soldering Station

• Ref.: CA-9QF 100V 50/60Hz. Input fuse: T2A. Output: 23.5V.
• Ref.: CA-1QF 120V 50/60Hz. Input fuse: T2A. Output: 23.5V.
• Ref.: CA-2QF 230V 50/60Hz. Input fuse: T1A. Output: 23.5V.
• Peak Power (Tool): 130 W
• Temperature Range: 90 – 450 °C / 190 – 840 °F
• Idle Temp. Stability (still air): ±1.5 ºC / ±3 ºF (Meets and exceed IPC J-STD-001)
• Temp. Accuracy: ±3% (Using reference cartridge)
• Temp. Adjustment: ±50ºC / ±90ºF (Through station menu setting)
• Tip to Ground Voltage/Resistance: Meets and exceed ANSI/ESD S20.20-2014 IPC J-STD-001F
• Earthing Fuse: F 1.25A
• Connections: USB connector station-PC RJ12 connector
• Ambient Operating Temp.: 10 – 50 ºC / 50 – 122 ºF
• Diameter of Solder Wire: from 0.8 – 1 mm / 0.03 – 0.04 in from 1.1 – 1.5 mm / 0.04 – 0.06 in
• Control Unit Dimensions / Weight: (L x W x H) 170 x 176 x 145 mm / 2.8 kg 6.7 x 6.9 x 5.7 in / 6.17 lb
• Total Net Weight: 2.91kg / 6.42 lb
• Total Package Dimensions / Weight: (L x W x H) 234 x 234 x 258 mm / 3.52 kg 9.2 x 9.2 x 10.2 in / 7.76 lb

Complies with CE standards. ESD safe.

Warranty

JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labor. The warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.
www.jbctools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>