Crystal Mountain SMT-C400002 Water Dispenser Instruction Manual

Crystal Mountain SMT-C400002 Water Dispenser

Notices and Safety Information

Throughout this manual there are paragraphs set off by special headings. “Notice” is used to emphasize installation, operation or maintenance information which is important, but may not present a hazard to persons or property. “Caution” is used when failure to follow directions could result in damage to equipment or property. “Warning” is used to indicate a hazard which could cause injury or death if ignored. The “Caution” and “Warning” paragraphs are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and careful attention are conditions which cannot be built into the equipment.

To ensure proper and efficient operation of the Crystal Pro Water Dispenser to your full satisfaction, carefully fol-low the instructions in this manual. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection be-fore the system. Check and follow the applicable plumbing codes and ordinances when installing this equipment. Local codes may prohibit the discharge of acidic or caustic solutions to drain. An extra solution tank may be required to neutralize the solution before discharging to drain. Follow local codes if they differ from this manual. This dispenser has a maximum pressure rating of 80 psi (5.5 bar). A pressure regulator must be used for all instal-lations. This will help prevent internal structural damage to the unit and potential water leaks. The pressure reg- ulator should be installed on the water supply before the inlet connection. Failure to use an appropriate anti-flood device for any reason will not obligate or make Crystal Moun-tain responsible in any wayfor Product Liability issues relating to any claims, including water damage claims. Regularly inspect the filters, filter housings and the plumbing fittings and connections for water leaks. Water leaks may cause damage to your office or facility and are not the responsibility of the manufacturer. Only connect the power cord to a properly grounded outlet.

NOTE: To provide additional protection from the risk of shock, this unit MUST be connected to a ground fault circuit interrupter (GFCI) outlet at all times. Use of an ex-tension cord will void any warranties. Keep the power cord out of heavy traffic areas. To avoid a fire hazard, never put the power cord under rugs, near radiators, stoves or heaters. Do not use a damaged power cord or plug. If the power cord is damaged, a qualified service technician must re- place it. This dispenser is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction con-cerning use of the dispenser by a person responsible for their safety. Children should be supervised to ensure that they do not play with the dispenser. This product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of ma- terial resources. To recycle your used dispenser, contact your local recycler or waste collector for the proper proce-dures.

• Please Dispose of Properly

Features & Benefits

Thank you for purchasing the Crystal Mountain Crystal Pro Water Dispenser. The Crystal Pro brings a fresh approach and a new look to point-of-use water dispensers. The system’s contemporary color scheme complements every office environment. There are no bottles to change and the supply is virtu-ally unlimited.

Hot, Cold & Ambient Dispenser
Your Crystal Pro Water Dispenser will provide up to 0.3 gallons (1.2 L) of hot water from a stainless steel reservoir using a 450 watt heating element. A bi- metal limiter is provided to prevent overheating and can be manually reset. The hot water is factory pre-set to 181°F (83 °C). Cold water is chilled with a high capacity compressor using R134 refrigerant. An electro-mechanical thermostat controls the tempera-ture of the water in the one gallon (3.8 L) stainless steel reservoir. The cold water temperature is facto-ry preset to a nominal 41°F (5 °C)

UV Light System
All models of the Crystal Pro dispensers are fitted with a UV-C band light system at the point of dispens-ing and built into the ambient reservoir lid. This system is used to inhibit the growth of bacteria. When dispensing Ambient or Cold water you will notice a pulsating “UV INSIDE” light which indicates the UV light system activation.

Leak Detection System
All models of the Crystal Pro are fitted with a leak detector. This system will generate an audible alarm and front panel light alert upon detecting water in the base of the unit. In addition, the system will au-tomatically shut off the incoming water supply to prevent further damage.

Filtration System (not included)
Crystal Pro dispensers are designed to be used with reverse osmosis, or carbon filtration. For locations where a drain is not present, a filtration-only option is recommended.

Internal Storage Reservoir
An internal storage reservoir eliminates the need for an external storage tank. The internal compart-ment is large enough to contain most water treatment systems. A float mechanism guards against over-flows.

Mechanical Components
All water connection fittings are compliant with NSF Standard 61. The Crystal Pro connects to the water supply using a 1/4″female bulkhead fitting. The molded panels are made from recyclable ABS plastic.

P = POU

| 3 = 3|

K=Black

| H=Hot, Cold &Ambient|

K =Black

| 1 = 110v-115v| C= Made in China

The Crystal Pro Water Dispensers come completely assembled and ready for set up and operation either with, or without, installation of reverse osmosis or filtration cartridges.Remove the dispenser from the box, saving the box and the packaging materials. The carton con-tains the following items:

• Qty Item
• 1 Crystal Pro Water Dispenser
• 1 M4 X 30 Tamper-proof Screw
• 1 M6 X 60 Expansion Bolt (220V units only – for CE compliance)
• 1 User Manual

Inspect the exterior for any damage which may have occurred during shipment.

1. To inspect the interior, remove the filtration service panel.
2. Visually inspect for any wires, tubing, or fittings which may have come loose during shipment.
3. Record the model and serial numbers below for future reference. Record your Crystal Pro model number here:

• Serial Number:
• Date purchased:
• Date installed:

Products offered and marketed by Crystal Mountain and its affiliates are protected by patents is

Parts Diagram

Parts Diagram Detail

Parts Listing

DESCRIPTION

1. Side Panel, Left SMT-C400002
2. Side Panel, Right SMT-C400003
3. Top Cover SUB-C400007
4. Lamp, Logo ELE-C100419
5. Cover, Back SMT-C400005
6. Solenoid, Low Pressure 24V DC (3 in unit) POU-C400001
7. Support Bracket, Rear Upper (2 in unit) SMT-C400008
8. Support Bracket, Front (2 in unit) SMT-C400007
9. Water Outlet PLC-C400015
10. Bulkhead Ftg, JG 1/4 x 1/4 POU-C000003
11. Bulkhead Ftg, JG 1/4 x 1/4 POU-C400012
12. Solenoid, High Pressure POU-C400002
13. Leak Detector Assy SUB-C400014
14. Panel, Lower Front SUB-C400035

• A Refrigeration System N/A
  • A1 Cold Control REF-C400004
  • A2 Overload REF-C100300
  • A3 Relay REF-C100229
  • A4 Cover, Compressor PW2.5DV REF-C100301
• B Upper Front Panel Assy SUB-C400033
  • B1 Upper Front Panel, Black N/A
  • B2 Grill, Drip Tray PLC-C400011
  • B3 Drip Tray Base PLC-C400009
  • B4 Cover, UV N/A
  • B5 PCB, UV Display N/A
  • B6 PCB, Push Button Module N/A
  • B7 Bracket, Push Button, Black N/A
• C Middle Front Panel Assy, Black SUB-C400034
  • C1 Middle Front Panel, Black N/A
  • C2 Bracket, Cup PLC-C400007
  • C3 Door Lock PLC-C400008
  • C4 Cup Dispenser, Outer PLC-C400023
  • C5 Cup Dispenser, Inner PLC-C400024
  • C6 Spring, Cup Dispenser FAS-C400011
  • C7 Cup Dispenser Bottom PLC-C400022
• D Top Shelf & Reservoir N/A
  • D1 Top Shelf SMT-C400013
  • D2 Transformer (120V/18V/1A) ELE-C400033
  • D3 Reservoir, Ambient PLC-C400001
  • D4 Lid, Reservoir PLC-C400002
  • D5 Float, Electronic ELE-C400026
  • D6 Float Valve, Mechanical POU-C400005
  • D7 UVC LED Module, 0.8W, 12-24 VDC ELE-C100401
  • D8 Water Outlet, SS, UV SMT-C100235
• E Hot Tank Assy SUB-C400001
  • E1 Hot Tank, SS N/A
  • E2 Heater Band ELE-C100298
  • E3 Heat Limiter ELE-C100170
  • E4 Thermostat ELE-C100109
• F PCB, Box & Cover Assy SUB-C400037
  • F1 PCB Box PLC-C400017
  • F2 Cover, PCB PLC-C400018
  • F3 Main PCB, UVC ELE-C100416
  • F4 Power Switch, Green ELE-C400007
  • F5 Power Switch, Red ELE-C400006
  • F6 Fuse, 10Amp ELE-C400032
  • F7 Power Cord ELE-C400029
• G 3/8” Pushfit Connector Assembly N/A
  • G1 DM Elbow, 1/4 x 3/8(AEU0604), Gray POU-C100071
  • G2 In-Line, Screen Filter, 3/8 (70 Mesh) POU-C100063
  • G3 “C” Clip, 8mm, Plastic MIS-C100222
  • G4 Union, JG 3/8 x 1/4 POU-C100026
  • G5 Tube, SS, 9.5mm OD x 95mm SMT-C100220

Parts Not Shown

• Adjustable Foot MIS-C400006
• Filter Bracket SMT-C400006

Installation

Position & Level

1. Locate the dispenser as close to the water supply and the electrical connections as possible.

2. Level the unit using the adjustable leveling feet and built-in level indicator.

3. Keep the dispenser at least 4 inches from the wall to ensure adequate airflow.
   Warning: The dispenser should not be exposed to direct sunlight, heat sources, or an ambient air temperature above 100°F (38°C) or below 37°F (3°C) or structural damage may occur.

4. To meet CE standards (if applicable), it is necessary to fasten the unit to the floor with an M6x60 expansion bolt.

• Locate and drill a 43 mm deep hole using an alloy drill bit with 9 mm diameter.
• Install the flat pad, the spring washer and the nut to the bolt, and then insert into the hole.
• Remove the filtration service panel and locate the alignment hole on the base plate.
• Align the dispenser with the expansion bolt using the hole in the base plate.
• Using a wrench, secure the unit to the expansion bolt.
• Reinstall the filtration service panel.

Your Crystal Pro Water Dispenser comes complete with a built-in cup holder under the water dispenser section. This holder is designed to hold up to twenty standard size cups with a diameter between 2.8″and 3.0″ (71 – 76mm).

Make Water & Electrical Connections

1. The dispenser contains push-to-connect type fittings on the rear of the unit for the water supply and R/O drain. These fittings accept ¼”polypropylene plastic tubing. If copper tubing is to be used, these fittings must be replaced with a metal design. In addition, drain ports are provided for the hot and cold tanks.

2. Connect a potable, cold water supply to the unit. Pressure must be 40-80psi (2.8-5.5 bar) and at a temperature no more than 105°F (41°C).

3. Flush the water supply feed until it runs clear before making connection to the dispenser.
   Caution:
   Installation should only be executed by trained personnel. Check and follow the applicable plumbing codes and ordinances when installing this equipment. The connection must be to the potable mains water supply and should be via a shut off valve. An Appropriate anti-flood device should be fitted as closely as possible to the mains connection point. In order to meet plumbing regulations, a backflow preventer may be required. Failure to use an appropriate anti-flood device for any reason will not obligate or make Crystal Mountain responsible in any way for Product Liability issues relating to any claims, including water damage claims. Do not connect the dispenser to a water line which exceeds 105°F (41°C) as structural damage may occur. This water dispenser has a maximum pressure rating of 80 psi (5.5 bar). A pressure regulator must be used for all installations. This will prevent internal structural damage to the unit and potential water leaks. This should be installed on the water supply before the dispenser water inlet.

4. Plug the dispenser into the wall outlet and verify that the green power status indicator is “on.” A fuse located on the rear service panel helps to protect the internal circuits from damage.

Caution:
Damage to the dispenser will result if hot and cold switches are turned on without water inside the tanks. If the unit was placed on its side, it must stand upright for a minimum of twenty-four hours before operation to allow the compressor to stabilize.

Install Filtration (if applicable)
The Crystal Pro is shipped from the factory with no internal filtration installed. Consult with your filter supplier on the best filtration solutions for the local water conditions and follow the manufacturer’s instructions on their installation, use and servicing.

Flush Filters (if applicable)
All filters must be flushed prior to use per manufacturer’s instructions. Depending upon your filtration or R/O system, this process may be combined with the initial sanitizing process. It is recommended to flush no less than two gallons through each filter. If using R/O, check to see if the filter manufacturer/supplier recommends soaking the R/O membrane (the R/O filter system is sold separately), prior to installation. Dispose of the first five gallons of product water.

Sanitize the Dispenser
You must sanitize your system before using it for the first time. Failure to do so may result in poor water taste and water quality. This is best accomplished as outlined below.

1. Ensure both water connections – supply and R/O drain (if applicable) are made at the rear of the unit.
2. Open top service panel to gain access to the main storage tank.
3. Open the filtration service panel.
4. Place a sanitization cartridge (this can be an empty filter cartridge or one supplied by your filter supplier not supplied with unit) inline before the water inlet of the unit.
5. Using a small eyedropper, prepare the sanitization cartridge by adding two teaspoons of unscented, liquid chlorine bleach.
6. Insert this cartridge inline prior to the system. If you have empty sanitization cartridges, install them in the filter positions. If you do not, remove your filtration system, then bypass it with a ¼’ polyethylenetubing and two – ¼” union quick connect fittings. Refer to the service manual of the filtration system being used for proper sanitization of your filtration system.
7. Slowly turn on the water supply until the main storage tank is ½ full then turn off.
8. Carry out a visual inspection for any water leaks.
9. Lift the main storage tank lid taking care not to damage the float sensor or UV light.
10. Wearing sterile gloves, and using a clean, lint-free cloth thoroughly wipe down the inside of the main storage tank with the bleach solution.
11. Let stand for ten minutes or until completely dry.
12. Slowly turn on the water supply.
13. Depress the dispensing buttons (alternate between hot, ambient and cold spigots) to allow the solution to run through the spigots and associated lines.
14. Drain the system until the chlorine bleach is no longer detected at the spigot. Drain the remaining water through the drain connection at the rear of the unit.
15. Remove the sanitization cartridge and install the filter and/or R/O cartridges.

Note: Remember to connect the R/O drain line to the R/O cartridge. Ensure that the flow restrictor is visible inside the R/O drain line
Note: If R/O is being used, allow several hours to completely fill all tanks The unit is supplied with a filter access door locking screw. This screw must be installed before the unit is put into service.

Turn on “Hot” & “Cold” Power Switches.

1. With all tanks completely filled with water, both the hot and cold switches at the rear of the dispenser should be turned “on.” It will take approximately twenty minutes for the hot water and two hours for the cold water to reach their temperature presets.
2. Record the service date on the inside filtration panel for future reference. This will ensure that maintenance intervals are recorded and scheduled.
3. Reinstall the filtration service panel.

Operating the Crystal Pro

Your Crystal Pro Water Dispenser contains a simple, intuitive user interface for operation and status. Hot and Cold buttons are backlit and a nightlight is provided in the dispensing area.

Always On

| Dispenser Unpowered| N/A

Ambient Button

| N/A| N/A| N/A
Cold Button|

Always On

| Dispenser Unpowered| N/A
UV Activation Light| UV System Ready*| UV System Ready| UV System Active
System Fault Indicator| UV Bulb Needs Replacement| UV System Ready| System Fault – i.e. Leak, Short-Circuit
Night Light| Dark Environment| Light Conditions| n/a

• On only when user is in front of the unit.

Note: To prevent the inadvertent dispensing of hot water, the dispense button must be held for 3 seconds until a beep is heard. Press the button again for water to dispense

Service & Maintenance

Once assembled, installed and flushed properly, your Crystal Pro Water Dispenser will provide years of trouble-free operation. Installation and service should only be carried out by a trained service professional. If applicable, filtration cartridges should be replaced every six months or as directed by the manufacturer. The hot water tank may require periodic descaling of mineral buildup inside the tank.

Service Notes

Caution:
Do not clean the water dispenser with a power washer or water jet device.

1. Sterile gloves must be worn when handling the filters, reservoir or any components that have contact with the drinking water.

General Maintenance

1. Wipe all surfaces on the front panels, dispensing buttons, dispenser area, faucet, and drip tray with an anti-bacterial cleaning wipe or spray.
2. Remove and clean the drip tray and grill. If the grill is damaged or heavily stained it should be replaced.
3. Wipe away any dust which may have accumulated on the condenser grill.
4. Drain both tanks after long periods of non-use.
5. On R/O models periodically inspect the flow restrictor to ensure it is clean and unrestricted.

Caution:
Use only factory-authorized replacement parts. Using unauthorized parts or accessories may cause damage or affect performance. Any damage, diminished performance or property damage from using unauthorized parts or accessories is not covered under the manufacturer’s warranty.

Sanitize Reservoirs

1. All water reservoirs should be sanitized at regular intervals, especially after a long period of non-use. This is best accomplished using a sanitization kit if available or by using the procedure outlined below.

2. Prepare water dispenser for the service

3. Turn off both the hot and cold switches at the rear of the unit.

4. Unplug the electrical supply to the unit.

5. Turn off the water supply to the unit.

6. Drain all water storage tanks using the drain ports located at the rear of the dispenser.
   Caution: Take care to prevent burns when draining the hot tank.

7. Remove the existing filtration cartridges

8. Open the front panel to gain access to the filtration compartment.

9. Remove all cartridges from the filter compartment.

10. For R/O systems, ensure that the drain line with flow restrictor between the R/O cartridge and drain port is removed first.

Install the Sanitization Cartridges

1. Place a sanitization cartridge (this can be an empty filter cartridge or one supplied by your filter supplier – not supplied with dispenser) inline before the water inlet of the unit.
2. Using a small eyedropper, prepare the sanitization cartridge by adding two teaspoons of unscented, liquid chlorine bleach.
3. Insert this cartridge inline prior to the system.
4. If you have empty sanitization cartridges install them in the remaining positions. If you do not, remove your filtration system, then bypass it with a ¼” polyethylene tubing and 2 – ¼” union quick connect fittings. Refer to the service manual of the filtration system being used for proper sanitization of your system.
5. Begin the sanitization process
6. Plug in the dispenser.
7. Slowly turn on the water supply.
8. Check for leaks or spills which may cause the leak detection system to activate.
9. Once all tanks are filled (approximately 3-5 minutes) let stand for 5-10 minutes.
10. Press and hold the hot, ambient and cold dispense buttons until water begins to flow.
11. Continue for 10 minutes, or until the bleach has been thoroughly flushed from the system.

Draining Reservoirs

1. Unplug the electrical supply to the unit.
2. Turn off the water supply to the dispenser.
3. Remove the cold drain plug on the rear to allow water to drain into a bucket.
4. Tilt the unit backward to facilitate draining of the water.
5. Repeat this process for the hot tank side.
6. Reinstall both drain plugs and verify they are secure.
7. Remove and replace cartridges
8. Remove all sanitization cartridges from the manifold or water inlet.
9. Turn water supply on and fill unit to flush remaining sanitizing agents then repeat steps 18-23
10. Install new filtration cartridges.
11. For R/O systems, ensure that the drain line is connected between the R/O cartridge and drain port. Verify that the flow restrictor is properly installed.
12. Record the service date on the filtration panel.
13. Wipe down the base of the filtration compartment and reinstall the filtration panel.
14. Return the dispenser to service
15. Wipe down the drip tray and all outer panels.
16. Clean any dust and debris from the condenser grill.

UV System Replacement

1. Turn off the “hot” and “cold” switches on the rear of the dispenser.

2. Turn off the water supply and activate the dispensing buttons to relieve any pressure in the unit.

3. Unplug the electrical cord from the wall socket.

4. Remove the top panel to gain access to the UV assembly either on the reservoir lid or in the water outlet tube. If replacing the UV on the reservoir lid, remove the lid from the reservoir.
   Warning:
   Do not remove the lamp from holder while illuminated and never look directly at the UV light as UV radiation is dangerous for the eyes and skin

5. Unplug the UV wire connector.

6. Remove the old UV assembly by gently pulling the assembly out of the outlet tube or by unscrewing the locknut if replacing the reservoir UV.

7. Install the new UV LED (Crystal Mountain part number ELE-C100401) by pushing into the outlet tube or, if replacing the LED in the reservoir lid, by securing it in place with the locknut.

8. Re-attach the wire connector.

9. Plug the electrical cord into the wall socket.

10. Slowly turn on the water supply.

11. If the UV on the water outlet tube was replaced, activate the dispensing buttons and check that there is no leak before installing the top panel.

12. Reinstall the top panel.

13. Turn on the “hot” and “cold” switches on the rear of the dispenser.

Reset Leak Detection System
All models of Crystal Pro Water Dispensers are equipped with a leak detection system. This system will generate an audible and visual warning upon detecting water in the base of the unit. In addition, the system will automatically shut off the incoming water supply valve to prevent further damage. The leak detection warning will stop once the leak is stopped and the affected area is dried out.

Service notes
If an audible “click” is heard within 5 minutes of turning on the red power switch, the hot tank is likely empty, and has overheated. The hot tank limiter will need to be reset.

Caution:
Turn off the hot tank and unplug the unit’s power cord before resetting the hot tank!

Troubleshooting

Specifications

Flow Diagram

Electric Diagram

Crystal Mountain Two Year Limited Warranty

FIRST YEAR:
Crystal Mountain Products Inc promises the original purchaser (user) to repair, or replace, at Crystal Mountain’s discretion, any part of this water cooler which proves to be defective in material or workmanship under normal use, for a period of one year from the date of the original purchase. During the first year of warranty, Crystal Mountain will provide parts, at no charge, necessary to repair the product, provided that the water cooler has been in- stalled and operated according to the manufac-turer’s written instructions. Failure to fol-low all instructions for operation and maintenance provided with this unit voids the warranty. The hot tank casing is to be free from defects in material and workmanship under normal use for 2 years. This does not include electrical wiring and components. If it becomes necessary to ship the inoperative water cooler to an authorized service center or to Crystal Mountain, the user will be responsi-ble for shipping the product, prepaid, via com-mon carrier. Local delivery charges are not covered. The warranty does not cover charges to dis-connect and reconnect plumbing and electrical connections. In addition, the warranty does not cover the cost of diagnostic charges, in-cluding any problems with the sealed refriger-ation system.

SECOND YEAR:
Crystal Mountain promises within the second year to repair, or replace, at its discretion, any part of the sealed refrigeration system which is determined to be defective in material or workmanship. If it becomes necessary to ship the defective water cooler to an approved service center or to Crystal Mountain, the user will be responsi-ble for shipping the product, prepaid, via com-mon carrier. Local delivery charges are not covered. The warranty does not cover charges to dis-connect and reconnect plumbing and electrical connections. In addition, the warranty does not cover the cost of diagnostic charges, in- cluding any problems with the sealed refriger-ation system.

GENERAL PROVISIONS AND EXCLUSIONS:
This warranty is only applicable within the Continental Limits of the United States of America and Canada. This warranty will be voided if the serial num- ber is removed, defaced or obliterated. This warranty will be voided if parts to repair the water cooler are not obtained from Crystal Mountain. In addition all service to the sealed refrigeration system must be performed by an authorized service agent or Crystal Mountain. This warranty does not cover any inoperative components which occur as a result of liming, scaling or other environmental conditions. This warranty does not apply to any water cooler or components that become inoperable because of a failure to satisfy standards or regulations adopted by any government or agency thereof, subsequent to the date of ship-ment from the factory. Crystal Mountain will not be liable for damage or wear to products caused by abnormal operating conditions, accident, abuse, misuse, unauthorized alteration or repair, or if the products were not installed in accordance with Crystal Mountain’s printed installation and operating in-structions, or for any damage caused by hot water, freezing, flood, fire, or acts of God.

WARNING
Crystal Mountain hereby disclaims any and all implied warranties including, but not limited to, the implied warran-ties of merchantability and fitness for a particular purpose. The manufacturer or its agents shall not be liable for con-sequential damages, whether economic or otherwise, resulting from breach of this limited warranty. Failure to follow all instructions for operation and mainte-nance provided with this unit voids the warranty. The foregoing is in lieu of all other agreements expressed, implied or statutory and all other obligations or liabilities of Crystal Mountain. Crystal Mountain does not assume or authorize any person to assume any obligations of liabil-ity in connection with this product. In no event will Crystal Mountain be liable for spe-cial or consequential damages or for any delay in the performance of this agreement due to causes beyond their control.

FILTER AND RO MEMBRANE LIMITED WARRANTY
Subject to the conditions and limitations de-scribed below, Crystal Mountain warrants their filter cartridges to be free from defects in ma-terial and workmanship at the time of installa-tion, or six months from the date of purchase, whichever comes first, when used within the operating specifications listed in the filter “Installation and Service Guide”.

RO MEMBRANE WARRANTY
Membranes carry a twelve (12) month pro-rated warranty as follows: Credit 1/12th of the replacement cost for each unused month pro-vided the system is installed and maintained according to factory instructions and the unit is operated within the specifications listed in the filter “Installation and Service Guide”.

CONDITIONS OF FILTER WARRANTY
The above warranty will not apply to the filters or RO membranes that are damaged because of neglect, misuse, alteration, accident, misap-plication, physical damage, fouling and/or scaling of membranes by minerals, bacterial attack, sediment, or damage caused by fire, acts of God, freezing, or hot water. If the filters/membrane are altered by anyone other than Crystal Mountain the warranty is void. Crystal Mountain assumes no warranty liability in connection with the Reverse Osmo-sis or Filtration system other than specified herein. Crystal Mountain will not be liable for any consequential damages of any kind or nature due to use of Crystal Mountain prod-ucts.

Crystal Mountain Products Inc. US Office

• 1000 H Taylor Station Rd
• Gahanna OH 43230
• Tel: 614 454 1618
• Fax: 614 866 7765
• E-mail: sales@crystalcoolers.com

Crystal Mountain Products Limited Canadian Office

• 200 Carnegie Dr Ste 234
• St Albert AB T8N 5A7
• Tel: 780 454 4545
• Fax: 780 454 9816
• E-mail: sales@crystalcoolers.com

European Office
Fence House, Fence Avenue Macclesfield, Cheshire United Kingdom SK10 1LT Tel: +44(0) 1625 439 111

• Fax: +44 (0) 1625 502 527
• E-mail: cmeurope@crystalcoolers.com

Crystal Mountain International Limited Hong Kong Office
Room 610, Winfield Commercial Building 6-8a Prat Avenue, Tsimshatsui Kowloon, Hong Kong Tel: (852) 2368 1989 Fax: (852) 3017 6727 E-mail: cmasia@crystalcoolers.com

References

• Crystal Mountain – Cooling the waters of the world!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>