BEHRINGER K10S Audiophile 10 Studio Subwoofer User Guide

: June 13, 2024
: Behringer

Table of Contents

Important Safety Instructions
LIMITED WARRANTY
NEKKST K8/K6/K5/K10S Hook-up
NEKKST K8/K6/K5/K10S Controls
NEKKST K8/K6/K5/K10S Getting started
Specifications
Other important information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NEKKST
K8/K6/K5
Audiophile Bi-Amped 8, 6, and 5″ Studio Monitor with Advanced Waveguide Technology
K10S
Audiophile 10″ Studio Subwoofer with High Excursion Woofer BEHRINGER
K10S Audiophile 10 Studio Subwoofer Quick Start Guide

Important Safety Instructions

Caution
RISK OF ELECTRIC SHOCK!
DO NOT OPEN

Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock.
Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section).No user serviceable parts inside. Refer servicing to qualified personnel.

Caution
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution
These service instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Use only attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or sold withthe apparatus. When a cartis used, use caution when moving the cart/apparatuscombination to avoid injury from tip-over
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall be connected to a MAINS socketoutlet with a protective earthing connection.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shallremain readily operable.
**** Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources.
For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
Do not install in a confined space, such as a book case or similar unit.
Do not place naked flame sources, such as lighted candles, on the apparatus.
Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
This apparatus may be used in tropical and moderate climates up to 45°C.

LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2023 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.

NEKKST K8/K6/K5/K10S Hook-up

Step 1: Hook-Up

BEHRINGER K10S Audiophile 10 Studio Subwoofer - Hook-
Up BEHRINGER K10S Audiophile 10
Studio Subwoofer - FIG

NEKKST K8/K6/K5/K10S Controls

Step 2: Controls

BEHRINGER K10S Audiophile 10 Studio Subwoofer -
Controls

K5/K6/K8

HIGH FREQUENCY – To compensate for room acoustic absorption.
LOW FREQUENCY – Adapts the monitor for use with a subwoofer, or emulates the characteristics of a smaller speaker.
ROOM COMPENSATION – Provides a low frequency roll-off to compensate for monitor placement.
INPUT TRIM – Adjusts the monitor’s input sensitivity to the audio source signal.
INPUT – Plug either an XLR, RCA or ¼” cable into one of these inputs to connect the audio source.
POWER SWITCH – Turns the unit on and off.
The front-panel logo lights when the power is turned on.
POWER SOURCE – Connect the included power cable to this socket and to a mains outlet properly configured for your model.
K10S
BALANCED OUTPUTS – XLR jacks send out full-range copies of each balanced XLR input signal.
LEVEL – Adjusts the subwoofer’s input sensitivity to the audio source signal.
CROSSOVER – Adjusts the crossover frequency to match the K5, K6, or K8 monitors, or other speakers in your system.
PHASE – Reverses the output phase to compensate for frequency cancellation between the subwoofer and monitors or other speakers.
LINE IN – Plug unbalanced RCA cables into one or both of these inputs to connect the audio source. The subwoofer plays a mono sum of the left and right inputs.
LINE OUT – RCA jacks send out full-range copies of each unbalanced RCA input signal.
BALANCED INPUTS – Plug XLR cables into one or both of these inputs to connect the audio source. The subwoofer plays a mono sum of the left and right XLR inputs.

NEKKST K8/K6/K5/K10S Getting started

Step 3: Getting started

Place the monitor speakers at head level, unobstructed and at equal distances to the left and right of your listening position.
For the K10S subwoofer, experiment with its position, such as in the corners or near the walls.
Connect the included power cables to each monitor and the subwoofer.
Connect the other ends to a mains outlet properly configured for your models. DO NOT turn the power on yet. If possible, connect everything to the same outlet to avoid ground loops.
Connect the audio source to the inputs of the monitors and subwoofer.
If connecting to a mixer, balanced outputs from the mixer are preferable. You may also connect the audio outputs from a computer using an interface such as the FCA1616. See the hook-up diagrams for some ideas.
Turn on your mixer, computer, or other audio source, with the volume at minimum.
Turn on the power to each monitor and the subwoofer by flipping their rear panel power switches.
Adjust the INPUT TRIM knob on the back of each monitor to the center (0 dB) position.
For the K10S subwoofer, adjust the LEVEL knob to the center (0 dB) position.
Adjust the CROSSOVER knob to suit the K5, K6, or K8 monitor.
Start playing your audio source and slowly increase the volume until you reach a comfortable listening level.
If required, adjust the monitor’s INPUT TRIM knob and the subwoofer’s LEVEL knob to obtain a good balance.

Specifications

K8
K6
K5
K10S

Amplifiers

Maximum output power| 150 W| 300 W
Configuration| Bi-amping| Mono
Type| Class-D
Overload protection| Dual-controlled limiter| Controlled limiter
Crossover type| Active
Crossover frequency| 3 kHz fixed| 3.2 kHz fixed| 40 to 150 Hz variable
Audio Connections

Inputs| 1 x XLR, balanced
1 x ¼” TRS, balanced
1 x RCA, unbalanced| 2 x XLR balanced inputs
2 x XLR balanced thru outputs
2 x RCA unbalanced inputs
2 x RCA unbalanced thru outputs
Max. input level| 14 dBu| 20 dBu
Controls
Volume| N/A| -∞ dB to 10 dB
Input trim| -6 dB to +6 dB| N/A
Low frequency| 0 / -2 / -4 / -6 dB @ 60 Hz, switchable| N/A
Room compensation| 0 / -2 / -4 / -6 dB @ 300 Hz, switchable| N/A
High frequency| 0 / +2 / -2 / -4 dB @ 8 kHz, switchable| N/A
Phase Correction| N/A| 0 / -180 degrees
Loudspeaker System Data

Type| 1″ tweeter 8″ woofer| 1″ tweeter 6″ woofer| 1″ tweeter 5.25″ woofer| 10″ woofer
Frequency response| 40 Hz to 20 kHz| 50 Hz to 20 kHz| 40 Hz to 150 Hz
Max. sound pressure level| Maximum 102 dB SPL @ 1m| Maximum 101 dB SPL @ 1m| Maximum 100 dB SPL @ 1m| Maximum 117 dB SPL @ 1 m
Physical

Enclosure| Baffle: Painted injection-molded PC and ABS
Enclosure: Matte black PVC laminated 15 mm MDF
Grille| N/A| Powder-coated galvanized perforated steel mesh grille
Power Supply / Voltage (Fuses)

Type| Switch mode power supply
Voltage| 100-240 VAC, 50/60 Hz| 100-240 VAC, 50/60 Hz (T 2.5 AH 250 V)
Power consumption @ 1/8 max power| 40 W| 50 W
Mains connection| Standard IEC connector
Dimensions / Weight

Other important information

Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com.
Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com.
Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model.
Faulty fuses must be replaced with fuses of the same type and rating without exception.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
NEKKST

Responsible Party Name:	Music Tribe Commercial NV Inc.
Address:	122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
Email Address:	legal@musictribe.com

NEKKST
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Important information:
Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.

Hereby, Music Tribe declares that this product is in compliance with Directive
2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/
EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom
We Hear You