MARLEY EM-JT010 Stir It Up Lux User Manual

: June 13, 2024
: MARLEY

Table of Contents

ATTENTION : PLEASE READ QUICK START GUIDE BEFORE USE
PRODUCT MAP
FUNCTION LAYOUT
SETUP
BALANCING THE TONEARM
ANTI-SKATING
PLAYING A RECORD
BLUETOOTH® PAIRING
DISCONNECT BLUETOOTH® PAIRING
VOLUME CONTROL
HEADPHONE OPERATION VIA HEADPHONE JACK
NON BLUETOOTH® CONNECTION SETUP
LINE OUT OPERATION
USB-C OUT PORT
Compliance Info
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MARLEY EM-JT010 Stir It Up Lux

MARLEY EM-JT010 Stir It Up Lux

ATTENTION : PLEASE READ QUICK START GUIDE BEFORE USE

PRODUCT MAP

LEGEND

Product Map

Spindle
Turntable
Balance Weight
Anti-Skating Knob
Tone Arm Lift Level
Tone Arm Rest Holder
Tone Arm
Stylus
Needle Cover
Multi-Function Button
Power Adaptor With 4 Interchangeable Plugs
45 Adaptor
Stylus Pressure Gauge

FUNCTION LAYOUT

LEGEND

A. RCA Line Out
B. Pre-Amp Switch Button
C. USB-C Out
D. Off/33 /45 Knob
E. Headphone Jack
F. Bluetooth® Button
G. – VOL + Knob
H. Anti-skating Knob

SETUP

ATTACHING THE DRIVE BELT

Note: The drive belt comes pre-installed. However, if when you open the turntable, there is no visible belt around the sub-platter and motor. Please re-fit the belt.
Attaching The Drive Belt

To fit the belt, put the belt on the motor (this is the gold spindle), then keeping the belt tight stretch it around the sub-platter. Once in place make sure the belt if flat and not twisted.
Now place the glass platter on the black sub-platter, by aligning the centre holes.
Now place the slip mat on the glass platter, again aligning the centre holes. The platter should be attached to the base.

BALANCING THE TONEARM

Option 1 (Without Stylus Pressure Gauge):

Push the Balance Weight on the tone arm until you feel a click.
Remove the stylus needle cover, before attempting to balance the tonearm.
Unclip the tonearm and from its rest , and make sure it is floating freely.
Rotate the Balance Weight back and fourth until the tone arm is parallel with the platter.
Now place the tonearm back into it’s rest and clip it in so it is secure. Now hold the balance weight so it cannot move, and with your other hand rotate the front dial until it is at 0. Your tonearm is now zeroed.
Now you need to add the correct tracking force for the stylus. You do this by now rotating the whole balance weight counter clock-wise until the correct weight is added. The correct tracking force for this stylus = 1.5g – 2.5g (2.0g standard).

NOTE: Once finished, if not using the turntable to play a record, put the stylus needle cover back on to protect the stylus when not in use.

Option 2 (Using Stylus Pressure Gauge):

Push the Balance Weight on the tone arm until you feel a click.
Remove the stylus needle cover, before attempting to balance the tonearm.
Unclip the tonearm and from its rest , and make sure it is floating freely.
Place the stylus pressure gauge onto the platter.
Place the stylus onto the 2-gram mark (recommended Tracking force for our stylus).
Rotate the balance weight back and fourth until the pressure gauge is level. Ensure that the needle stays on the 2g mark.

ANTI-SKATING

Anti-skate applies a small outward force to the tonearm. This is to counteract the tendency of the arm to move inward (skate) toward the centre of the record, especially as the record approaches the centre of the record.
The Anti-Skate should match the tracking force added. So for our turntable, set to 2.

PLAYING A RECORD

Make sure the Stir It Up Lux is connected to the power adapter and a wall outlet, and the outlet is switched on.
Put a vinyl on the turntable.
Make sure the stylus needle cover is removed.
Turn the RPM dial to the correct speed for the record. E.g. 45 / 33.
If wanting to play via Bluetooth – Please see the “Bluetooth Pairing” section and then come back here once connected to an output device. If wanting to play via Line out or Headphone out – please check their sections on how to connect the output device. And then come back here.
Lift the tonearm via the lift lever and move the tonearm head to the edge of the record.
Now lower the tonearm, by lowering the tone arm lift lever.

NOTE: The turntable platter will auto-start spinning once the tonearm is above the platter.
Once the record is finished, the turntable platter will auto stop. Lift the tonearm and place it on the tonearm rest. To listen to the B side of your record, flip the record and repeat the above from step 6.

NOTE: Once finished listening to a record, make sure the stylus needle cover is re-attached to protect the stylus.

Do not try to adjust the balance weight or anti-skate while playing a record, this could break the stylus needle and scratch the record.

Do not try to turn the turntable platter manually. Moving or jarring the turn – table without securing the tonearm, could result in damage to the tonearm.

Re-secured the tone arm before transportation to protect the needle.

Remove the balance weight before transportation to prevent damage or breakage to the unit.

BLUETOOTH® PAIRING

Power on the external Bluetooth® device first before turning on the BT function on the Turntable.
Press the BT button on the turntable (MFB) to enable the unit to search the Bluetooth® device till BT indicator light becomes solid. This will indicated your devices are paired.

NOTE: If the Turntable does not pair with your Bluetooth® device within 30 seconds, press the Bluetooth® search button again on the turntable and it should pair.
Bluetooth® Pairing

Blue LED light flash
Blue LED light stable

DISCONNECT BLUETOOTH® PAIRING

Long press and hold the BT button till the BT indicator light turns off. Turntable will then disconnect from external device.

Blue LED light will turn to Red. This indicates Bluetooth is off, but turntbale still has power.

VOLUME CONTROL

Increase Volume: Rotate the Volume Knob clockwise.
Decrease Volume: Rotate Volume Knob counter clockwise.

HEADPHONE OPERATION VIA HEADPHONE JACK

Connect a set of headphone (not included) in the headphone jack.

Note: Never put on the headphone till you have plugged in the headphone plug.

NON BLUETOOTH® CONNECTION SETUP

LED will also be solid RED when headphones are plugged in.

CAUTION: Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord.

LINE OUT OPERATION

Switch the PRE-AMP OFF/ON SWITCH to ON position.
Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit. Be sure to match the color with the socket.
Plug the other end of the cable into the LINE IN socket of your home amplifier device.
Switch on the unit and the amplifier device you connected.
Adjust the volume on the amplifier device.

USB-C OUT PORT

You can use the USB-C out port to charge any of your devices from here. We can recommend charging a House of Marley Speaker from this to save on plug adaptors0.

Compliance Info

STIR IT UP LUX

READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions ,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

FCC RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To Maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

ISEDC STATEMENT
This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

The device complies with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

This Class B digital apparatus complies with Canadian ICES-003.

The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be obtained from www.thehouseofmarley.co.uk/declaration-of- conformity.

To prevent possible hearing damage, do not listen at high volume levels for long periods.
Full instruction and warranty details can be found at http://www.thehouseofmarley.com/instructionbooks

FKA Distributing Co., LLC / China : R-C-DMV-EM-JT010, EM-JT010
(Product name): Stir It Up LUX Turntable
(Model): EM-JT010
(Operation Frequency): Bluetooth (2402 – 2480 MHz)
(Radio Channel): 79channels for BDR/EDR
(Bluetooth Mode): BT 5.3
(Output Power): 3mW
(Antenna Gain): 0dB
(Modulation Type): GFSK、π/4-DQPSK
(Power Supply): 15 V

Marley and the Marley logo are registered trademarks of Fifty-Six Hope Road Music Limited and the use of such marks by House of Marley is under license. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The House of Marley is under license.

Operating frequency band: 2402 – 2480MHz
CE Maximum radio-frequency power transmitted: 2.64dBm

DISTRIBUTED BY:
The House of Marley, LLC
3000 North Pontiac Trail, Commerce Township,
MI 48390 USA

Imported into the UK by
FKA Brands Ltd, Ton bridge, TN110GP, UK.

Imported into the EU by
FKA Brands Ltd, 29 Earlsfort Terrace, Dublin 2. IE

Distributed in Australia by
Homedics Australia Pty Ltd
14 Kingsley Close
Rowville, Victoria 3178

Distributed in New Zealand by
CDB Media Ltd
4 Lovell Court
Albany, Auckland, New Zealand 0800 232 633

IB-EMJT010SB-1222-01
Symbols

| RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment . User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment
---|---
| This symbol indicates class II equipment
| This symbol indicates AC voltage
| This symbol indicates for indoor use only
| This symbol indicates DC voltage
| This symbol indicates energy efficiency marking.
The power adaptor plug is used as the disconnect device, The connected AC power outlet must be located near the equipment and be easily accessible.
The marking information is located at the bottom of the apparatus.
WARNING: Only the accessories (such as external power supply) provided by the manufacturer can be used with the product .
Adapter Information Manufacturer : Shenzhen Aquilstar Technology Co, Ltd . Model: ASS A107 W-150080 Input: 100-240 V-50/60Hz 0.45A Output: 15.0V , 0.8A, 12W

Customer Support

©Fifty-Six Hope Road Music Ltd., 2011-2023.
Right of Publicity and Persona Rights.
Fifty-Six Hope Road Music Ltd. EM-JT010 Marley, the Marley logo, Bob Marley and the Bob Mar –
ley logo are registered trademarks of Fifty-Six Hope Road Music Limited and any use of such marks by The House of Marley is under license. The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The House of Marley is under license.

|
---|---