Molly Lac DM-208 65W Nail Drill User Manual
- June 13, 2024
- Molly Lac
Table of Contents
Molly Lac DM-208 65W Nail Drill
Preparation for Operation
- Gently insert the chosen attachment until it clicks into place.
- Set the potentiometer to the MIN position.
- Turn on the device using the switch in either the hand position\ for manual control or the foot position for pedal control.
- Gradually adjust the speed based on the size and type of bur or abrasive wheel (speed can be adjusted using the knob on the device or the foot pedal).
Technical Parameters:
| Voltage | Power | Power Supply | Rotations |
|---|---|---|---|
| 220-230 V / 50 Hz | 65W | 12 V DC | 25000 |
Work Attachments:
An attachment consists of a shaft and a cutting part, most commonly made of
stone, metal, or diamond. Attachments can have different grits. Felt and brush
attachments are also available.
ATTENTION! Metal burs only cut when rotating in the right direction. For
stones and diamonds, rotation direction does not matter.
Importer Information:
- Importer: Michal Szewczyk, Piotr Malinowski s.c.
- NIP: 7252093973
- REGON: 362455183
- Made in P.R.C.
Preparation for Operation
- Gently insert the chosen attachment until it clicks into place.
- Set the potentiometer to the MIN position.
- Turn on the device using the switch in either the “hand” position for manual control or the “foot” position for pedal control.
- Gradually adjust the speed based on the size and type of bur or abrasive wheel (speed can be adjusted using the knob on the device or the foot pedal).
Technical Parameters
- Voltage: 220-230 V / 50 Hz / Power: 65W / Power Supply: 12 V DC / Rotations: 25000
ATTENTION:
Nail cutters may heat up at higher speeds. The pressure applied while using
them requires practice.
Excessive speed and pressure can cause nail burning. The selection of
rotational speed depends on the diameter of the bur. The larger the bur or
stone, the lower the speed should be set.
Installation
- For safety reasons, the device must be disconnected from the electrical outlet while installing the pedal, handle, or burs. Connect the handle and pedal to the appropriate inputs on the device. Attach the burs after turning the movable part of the handle to the left.
- After inserting the bur, turn the movable part of the handle to the right.
- Once the accessories and burs are attached, the device can be connected to the electrical outlet.
Maintenance:
- Metal, stone, and diamond burs can be sterilized using a sterilizer.
- Felt burs and brushes should be cleaned with a disinfectant solution.
NOTES:
- If the power cord is damaged, it must be replaced with the same type by a service center.
- Making independent switches or modifications to the device is prohibited.
- Opening the device is strictly prohibited and will void the warranty; the manufacturer will not be responsible for the proper and safe functioning of the device.
- Keep out of reach of children.
- Store and use in dry environments.
- It is recommended to use a dust extractor; dust accumulation can damage the device.
Work Attachments:
An attachment consists of a shaft and a cutting part, most commonly made of
stone, metal, or diamond. Attachments can have different grits. Felt and brush
attachments are also available.
ATTENTION!
Metal burs only cut when rotating in the right direction. For stones and
diamonds, rotation direction does not matter.
DISPOSAL
- In accordance with Article 14 of the Directive 2012/19/EU of the European Parliament and of the Council dated July 4, 2012, regarding Waste Electrical and Electronic Equipment (WEEE), we would like to provide information about the proper disposal of waste electrical and electronic equipment:
- It is prohibited to dispose of waste electrical and electronic equipment together with other waste – this is confirmed by the “crossed-out wheeled bin” symbol, which indicates the need for separate collection of this type of waste. Electrical and electronic devices may contain hazardous substances, mixtures, and components that, if released into the environment, can pose serious threats to the health and life of people and living organisms.
- Disposed electrical and electronic equipment should be exclusively delivered to authorized collection points, the list of which should be available on the website of each Municipality Office.
- Households play a crucial role in the waste management system for used electrical and electronic equipment, as they have the opportunity to directly deliver them to authorized collection points and eliminate undesirable social practices resulting in the improper disposal of used equipment in unauthorized locations.
IMPORTER:
Michał Szewczyk, Piotr Malinowski s.c. 90-361 Łódź ul. Piotrkowska 270 NIP
7252093973 REGON 362455183
Made in P.R.C.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>