behringer ULM200M High-Performance 2.4 GHz Digital Wireless System User Guide

behringer ULM200M High-Performance 2.4 GHz Digital Wireless System

Product Information

The ULTRALINK ULM202USB/ULM200USB is a high-performance 2.4 GHz digital wireless system with handheld microphone(s) and a dual-mode USB receiver. It is designed to provide wireless microphone capabilities for various applications.

ULM202USB/ULM200USB Controls

1. POWER/STATUS LED
2. VOLUME Button (Mute/volume down)
3. VOLUME Button (Power on/unmute/volume up)
4. USB connector
5. Wireless Link Status LED

ULM200USB/ULM202USB Getting Started

1. Connect the ULM200D wireless receiver to the WIRELESS ONLY! USB connector on wireless-enabled BEHRIINGER mixers, powered speakers, or other compatible products, or to a USB port on a computer.
2. Press and hold the button on the ULM200M wireless microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will flash slowly during the connecting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the volume buttons to adjust the volume.
4. A long press of the volume button will put the ULM200M microphone into mute. The mute condition is indicated by rapid flashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the volume button will unmute the ULM200M microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level. If unmuted after less than 10 seconds, it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the battery is low by regular brief flashes.

Specifications

• RF output
• Operating range
• Dynamic range
• Equivalent input noise
• Frequency Response (Wireless Link)
• Sampling rate
• Resolution
• Encoding
• Latency
• RF frequency
• USB current consumption
• Battery type
• Battery life
• Dimensions (W x D x H)
• Weight

ULTRALINK ULM202USB/ULM200USB
High-Performance 2.4 GHz Digital Wireless System with Handheld Microphone(s) and Dual-Mode USB Receiver

ULM202USB/ULM200USB Hook-Up

ULM202USB/ULM200USB Controls

Type of product: Wireless Microphone

ULM200USB/ULM202USB Controls

1. POWER/STATUS LED
2. ▼ VOLUME Button (Mute/volume down)
3. ▲ VOLUME Button (Power on/unmute/volume up)
4. USB connector
5.  Wireless Link Status LED

ULM200USB/ULM202USB Getting Started

1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connector on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible products, or to a USB port on a computer.

2. Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will flash slowly during the connecting sequence and will light solid once connected.
   If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.

3. Once connected, the ULM200M microphone will be set at
   a medium volume. Use the ▲ and ▼ buttons to adjust the volume

4. A long press of the ▼ button will put the ULM200M microphone into mute. The mute condition is indicated by rapid flashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.

5. A short press of the ▲ button will unmute the ULM200M microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.

6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.

7. The LED in the ULM200M wireless microphone will indicate when the battery is low by regular brief flashes.

8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will flash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down after 10 seconds.

Specification

*Achievable range will be dependent on nearby sources of RF interference and/or line-of-sight obstacles.
**Measured from analog input to analog output, unity gain operation without wireless compression.

LEGAL DISCLAIMER

MUSIC Tribe accepts no liability for any loss that may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and COOLAUDIO are trademarks or registered trademarks of MUSIC Tribe Global Brands Ltd. © MUSIC Tribe Global Brands Ltd. 2018 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC Tribe’s Limited Warranty, please see complete details online at musictri.be/warranty.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible Party Name: MUSIC Tribe Commercial NV Inc.
Address: 5270 Procyon Street Las Vegas, NV 89118 USA
Phone Number: +1 702 800 8290

ULTRALINK ULM202USB/ULM200USB
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Tribe can void the user’s authority to use the equipment.

RF EXPOSURE:

• This equipment meets the government’s requirements for exposure to radio waves, and has been tested and meets the FCC RF exposure guidelines.
• The highest SAR value (1g) for this ULM200D Receiver is 0.649 W/kg.
• The highest SAR value (1g) for this ULM200M wireless microphone is 0.774 W/kg.
• This equipment complies with the European Council Recommendation of 12 July 1999 on the Limitation of Exposure of the General Public to Electromagnetic Fields [1999/519/EC].

Operation in the 2.4 GHz ISM (Industrial, Scientific, Medical) frequency band may be subject to interference from other transmitting equipment operating in this band. In the event of such interference, please verify and reassign the transmitting channels of any potentially interfering transmitting equipment.
We Hear You

References

• Music tribe – Music is life

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>