Honeywell M8635212 Electronic Deadbolt Lighted Keypad Touchscreen Instruction Manual

: June 13, 2024
: Honeywell

Table of Contents

Installation Overview
Install Enclosed Latch and Strike Plate
Install Exterior Assembly
Install Interior Assembly
Install Interior Assembly
Install Batteries and Cover
Testing Operation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Honeywell M8635212 Electronic Deadbolt Lighted Keypad Touchscreen Instruction Manual

Read this manual carefully before installing and operating!

Important
Use the QR code below for the most up to date instructions:

https://cdn.shopify.com/s/files/1/0582/1143/4684/files/M8635212_8635214_Raven_DB_E_QR_code.pdf?v=1676473670

Tools Needed for Lock Installation:

Phillips Screwdriver

Installation Overview

Package Includes:

1 – Exterior Faceplate
1 – Interior Faceplate
1 – User Guide
2 – Keys
1 – Strike Plate
1 – Mounting Plate
1 – Latch
1 – 1 3/8” Screws
2 – 5/16” Screws
2 – 1” Screws
4 – 3/4” Screws
2 – Mounting Post
Optional Set Screw

Please carefully check the above list to confirm all items have been received. If any items are missing, please contact Consumer Assistance. (See page for contact information

Read this manual carefully before installing and operating

Install Enclosed Latch and Strike Plate

Do not over-tighten latch screws.
NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm)
Dimension
TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET:

Hold latch with numbers facing forward and thumb pressing on the bolt.
Rotate the cylinder cover clockwise.
Pull and twist the extension plate all the way out.
Rotate the cylinder counter clockwise so that the marking aligns with the 2-3/4” position indicator

The latch plate on the door needs to be straight and not protruding from door. Make adjustment before installing or this will cause problems with bolt tting into latch hole

Deadbolt Latch Must Be Retracted During Installation.

Preparation for Interior Assembly.
Remove (J) Screw from inside the battery compartment within the (B) Housing to release the Mounting Plate (C)

Screw Mounting Post (M) into holes on Mounting Plate (C).
Interior Assembly

Install Exterior Assembly

Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION.

Route the Control Wire through the door UNDER the Deadbolt Latch Set. Make sure the door is shut, lock and unlock using the key, ensure that the latch is operating smoothly and is aligned properly without scraping the strike plate. If not, go back to step 2 and ensure you followed the steps
Connection
Work with the door open

(L) screw goes into the door to prevent the lock from shifting and is optional
Screw Inserting
Secure mounting plate to door

Install Interior Assembly

Install Interior Assembly
Work with the door openc

NOTE: Make sure the connector dots line up with the dots on the controle wire

Install Interior Assembly

NOTE: Make sure the Knob is in the correct position. Be careful not to pinch the control wire when assembling
Install Exterior Assembly
**Test the lock

** Lock and unlock using the thumb knob make sure the latch is opening and closing easily. If not, go back to step 2 and ensure you followed the steps

Install Batteries and Cover

This Electronic lock requires (4) High Quality AA Alkaline batteries. When all 4 batteries are installed in the correct position, you should hear 2 beeps and the keypad will illuminate.

The Lock motor will engage and do a series of locking andunlocking motions in order to automatically determine your door “Handing” (left or right handed door). The lock will beep and the touchscreen will flash signaling success

NOTE: Do not touch the touchscreen until the light turns off. Do not use rechargeable batteries or non-alkaline batteries.

Testing Operation

Test the lock button with door open
Testing Operation
Test unlocking Press 1-2-3-4-5-6-

** Before Opening Door Let Motor Complete Cycle
Note:** Let lock operation complete before attempting another action

Preparing Door
Tools Needed for Door Preparation (if there is no knob hole)

Drill
2 1/8” Hole Saw
1” Hole Saw
3/4” Chisel

NOTE: Skip this step if your door comes with pre-drilled holes.

Refer to Template included for Door Prep Instructions

2 1/8” Hole Saw
1” Hole Saw

Strike Plate Installation
NOTE: The strike plate on the door frame needs to be straight and not protruding from door frame. Make adjustment before installing or this will cause problems with bolt fitting into latch hole.