SHARP R-1514 Microwave Oven Owner’s Manual

: June 13, 2024
: Sharp

Table of Contents

R-1514 Microwave Oven
Product Information
Precautions to be Observed Before and During Servicing
Warning to Service Personnel
Before Servicing
Microwave Measurement Procedure

R-1514 Microwave Oven

Product Information

The R-1514 is a microwave oven that contains circuitry capable
of producing very high voltage and current. It is important to
follow safety precautions and instructions to avoid possible
exposure to excessive microwave energy and electrical shock.

Precautions to be Observed Before and During Servicing

Do not operate or allow the oven to be operated with the door
open.
Make safety checks on all ovens to be serviced before
activating the magnetron or other components.

Warning to Service Personnel

Microwave ovens contain circuitry capable of producing very high
voltage and current. Contact with certain parts may result in a
severe, possibly fatal, electrical shock. These parts include the
high voltage capacitor, high voltage power transformer, magnetron,
high voltage rectifier assembly, and high voltage harness.

Before Servicing

Disconnect the power supply cord.
Open the door and block it open.
Discharge the high voltage capacitor.

Microwave Measurement Procedure

When all service work is completed and the oven is fully
assembled, it is recommended to check the microwave power output
and perform a microwave leakage test.

Product Usage Instructions

1. Before servicing the microwave oven:

Disconnect the power supply cord.
Open the door and block it open.
Discharge the high voltage capacitor by short-circuiting the
connection against the chassis using an insulated screwdriver.

2. When troubleshooting is performed, always disconnect the
power supply before starting. If necessary to connect the power
supply after removing the outer case:

Disconnect the power supply cord.
Remove the outer case.
Open the door and block it open.
Discharge the high voltage capacitor.
Disconnect the leads to the primary of the power transformer
and isolate them using insulation tape.
Reconnect the power supply cord after completing the
procedure.

3. After testing is completed:

Disconnect the power supply cord.
Remove the outer case.
Open the door and block it open.
Discharge the high voltage capacitor.
Reconnect the leads to the primary of the power
transformer.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is
installed.
Run the oven and check all functions.

4. After repairing:

Reconnect all leads removed from components during
testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is
installed.
Run the oven and check all functions.

Note: Microwave ovens should not be run empty. To test for
microwave energy, place a cup of cold water on the turntable, close
the door, set the power to HIGH, and set the microwave timer for
two (2) minutes. After the timer reaches zero, check that the water
is hot. If it remains cold, repeat the Before Servicing procedure
and reexamine the connections to the component being tested.

R-1514
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse. (c) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. (d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. (e) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner.
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave Measurement Procedure outlined in this service manual. If microwave emissions level is in excess of the specified limit, contact SHARP ELECTRONICS CORPORATION immediately @1-800-237-4277. If the unit operates with the door open, service person should 1) tell the user not to operate the oven and 2) contact SHARP ELECTRONICS CORPORATION and Food and Drug Administration’s Center for Devices and Radiological Health immediately. Service personnel should inform SHARP ELECTRONICS CORPORATION of any certified unit found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use the unit until the oven has been brought into compliance.
32

R-1514

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all instructions.

Don’t Touch ! Danger High Voltage

Before Servicing

1. Disconnect the power supply cord outer case.
2. Open the door and block it open. 3. Discharge high voltage capacitor.

, and then remove

WARNING: RISK OF ELECTRIC SHOCK. DISCHARGE THE HIGH-VOLTAGE CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60 seconds after the oven has been switched off. Wait for 60 seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an insulated screwdriver.

Whenever troubleshooting is performed the power supply must be disconnected. It may, in some cases, be necessary to connect the power supply after the outer case has been removed, in this event, 1. Disconnect the power supply cord, and then remove
outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the leads to the primary of the power
transformer. 5. Ensure that these leads remain isolated from other
components and oven chassis by using insulation tape. 6. After that procedure, reconnect the power supply cord.

When the testing is completed, 1. Disconnect the power supply cord, and then remove
outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Reconnect the leads to the primary of the power
transformer. 5. Reinstall the outer case (cabinet). 6. Reconnect the power supply cord after the outer case is
installed. 7. Run the oven and check all functions.
After repairing
1. Reconnect all leads removed from components during testing.
2. Reinstall the outer case (cabinet). 3. Reconnect the power supply cord after the outer case is
installed. 4. Run the oven and check all functions.
Microwave ovens should not be run empty. To test for the presence of microwave energy within a cavity, place a cup of cold water on the oven turntable, close the door and set the power to HIGH and set the microwave timer for two (2) minutes. When the two minutes has elapsed (timer at zero) carefully check that the water is now hot. If the water remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully assembled, the microwave power output should be checked and microwave leakage test should be carried out.

1

R-1514
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:

Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
Safety interlock switches: Primary interlock switch shall prevent microwave radiation emission in excess of the requirement as above mentioned, secondary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of 5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing: Before beginning the actual measurement of leakage, proceed as follows: 1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important: Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
Place the oven tray in the oven cavity. 3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5°C (68°F) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and made of an electrically nonconductive material such as glass or plastic. The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage is measured accurately. 4) Set the cooking control on Full Power Cooking Mode 5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement) 1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven. 2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on
the meter. 3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents). While testing for leakage around the door pull the door away from the front of the oven as far as is permitted by the closed latch assembly. 4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and that the primary interlock switch and the secondary interlock relay do turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2

R-1514
SERVICE MANUAL
OVER THE RANGE MICROWAVE OVEN
R-1514 FOREWORD This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP OVER THE RANGE MICROWAVE OVEN, R-1514. The model R-1514 are quite similar to base models R-1500 and R-1501 (Reference No. is S8123R1500X//). It is recommended that service personnel carefully study the entire text of this manual and base model service manual so that they will be qualified to render satisfactory customer service. Check the interlock switches and the door seal carefully. Special attention should be given to avoid electrical shock and microwave radiation hazard.
WARNING Never operate the oven until the following points are ensured. (A) The door is tightly closed. (B) The door brackets and hinges are not defective. (C) The door packing is not damaged. (D) The door is not deformed or warped. (E) There is not any other visible damage with the oven. Servicing and repair work must be carried out only by trained service personnel.
DANGER Certain initial parts are intentionally not grounded and present a risk of electrical shock only during servicing. Service personnel – Do not contact the following parts while the appliance is energized; High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness; If provided, Vent Hood, Fan assembly, Cooling Fan Motor. All the parts marked “*” on parts list are used at voltages more than 250V. Removal of the outer wrap gives access to voltage above 250V. All the parts marked “” on parts list may cause undue microwave exposure, by themselves, or when they are damaged, loosened or removed.
SHARP ELECTRONICS CORPORATION SHARP PLAZA, MAHWAH, NEW JERSEY 07430-2135
3

R-1514
ITEM Power Requirements Power Output Case Dimensions Cooking Cavity Dimensions 1.5 Cubic Feet Hood lamp Hood fan Control Complement
Oven Cavity Light Safety Standard Weight

PRODUCT SPECIFICATION

DESCRIPTION
120 Volts / 14 Amperes / 1600 Watts 60 Hertz Single phase, 3 wire grounded
1000 watts (IEC TEST PROCEDURE) Operating frequency of 2450MHz
Width 29-15/16″ Height 16-1/4″ Depth 15- 9/16″
Width 17-1/2″ Height 9-7/8″ Depth 14-15/16″
2 bulbs, 20W x 2, Incandescent light bulbs
Approx. 300 C.F.M.
Touch Control System Clock ( 1:00 – 12:59 ) Timer (0 – 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate; P-HI ………………………………………….. Full power throughout the cooking time P-90 ………………………………………………………….. approx. 90% of Full Power P-80 ………………………………………………………….. approx. 80% of Full Power P-70 ………………………………………………………….. approx. 70% of Full Power P-60 ………………………………………………………….. approx. 60% of Full Power P-50 ………………………………………………………….. approx. 50% of Full Power P-40 ………………………………………………………….. approx. 40% of Full Power P-30 ………………………………………………………….. approx. 30% of Full Power P-20 ………………………………………………………….. approx. 20% of Full Power P-10 ………………………………………………………….. approx. 10% of Full Power P-0 ……………………………………………. No power throughout the cooking time

KEEP WARM PLUS pad,HOT WATER pad, CUSTOM HELP pad INSTANT SENSOR pads, SENSOR COOK CENTER pads REHEAT pads, DEFROST CENTER pad, Number selection pads POWER LEVEL pad, TIMER / CLOCK pad LIGHT HI / LO button, FAN HI / LO button, STOP/CLEAR button, START/ MINUTE PLUS button,

20W x 1 Incandescent light bulb

UL Listed

FCC Authorized

DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J

Approx. 55 lbs.

4

R-1514

SENSOR COOKING CONDITION
Using the Sensor Cooking function, the foods are cooked or defrosted without figuring time, power level or quantity. When the oven senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining cooking time and power level needed for best results. When the food is cooked, water vapor is developed. The sensor “senses” the vapor and its resistance increases gradually. When the resistance reaches the value set according to the menu, supplementary cooking is started. The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI.
An example of how sensor works (Baked potatoes):

1. Potatoes at room temperature. Vapor is emitted very slowly.

MICROWAVE

2. Heat potatoes. Moisture and humidity is emitted rapidly. You can smell the aroma as it cooks.

AH SENSOR MICROWAVE

3. Sensor detects moisture and humidity and calculates cooking time and variable power.
Cooking Sequence. 1. Operate the oven in sensor cooking mode by referring to
operation manual. NOTE: The oven should not be operated on Sensor Cooking
immediately after plugging in the unit. Wait two minutes before cooking on Sensor Cooking. 2. The coil of shut-off relay (RY1) is energized, the oven lamp, turntable motor and cooling fan motor are turned on, but the power transformer is not turned on. 3. After about 32 seconds, the cook relay (RY2) is energized. The power transformer is turned on, microwave energy is produced and first stage is started. The 32 seconds is the cooling time required to remove any vapor from the oven cavity and sensor. NOTE: During this first stage, do not open the door or touch STOP/CLEAR pad. 4. When the sensor detects the vapor emitted from the food, the display switches over to the remaining cooking time and the timer counts down to zero. At this time, the door may be opened to stir food, turn it or season, etc. 5. When the timer reaches zero, an audible signal sounds. The shut-off relay and cook relay are de-energized and the power transformer, oven lamp, etc. are turned off. 6. Opening the door or touching the STOP/CLEAR pad, the time of day will reappear on the display and the oven will revert to an OFF condition.

NOTE: ” ” indicates components with potential above 250V.

CAVITY THERMAL CUT-OUT

MAGNETRON TEMPERATURE FUSE

BLK

FUSE 20A
HOOD FAN THERMAL CUT OUT GRN
120 V AC. GND 60 Hz

CONTROL UNIT N.O.

COM. E2

A5

RY4

B5 RY3

High B7

N.C.

B9 Low HOOD CAPACITOR

RY6 RY5

OVEN LAMP RELAY
RY1

RY2
SECONDARY INTERLOCK RELAY

DOOR SENSING SWITCH E1 F1 F2
F3

HOOD A1 A3 B1 MOTOR

B3 N.O.

COM.

WHT

HOOD LAMP

HL

OL

TTM

FM

AH SENSOR

SCHEMATIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2. CLOCK APPEARS ON DISPLAY.
POWER TRANSFORMER
HIGH VOLTAGE CAPACITOR 0.94µF/ AC2300V
HIGH VOLTAGE RECTIFIER

MAGNETRON

OVEN LAMP TURNTABLE MOTOR
FAN MOTOR MONITOR SWITCH

PRIMARY INTERLOCK SWITCH
Figure O-1. Oven Schematic-Off Condition
6

R-1514

CAVITY THERMAL CUT-OUT

MAGNETRON TEMPERATURE FUSE

SCHEMATIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2. COOKING TIME PROGRAMMED. 3. VARIABLE COOKING CONTROL “HIGH”. 4. “START” BUTTON PRESSED.

WHT

BLK

FUSE 20A
HOOD FAN THERMAL CUT OUT GRN
120 V AC. GND 60 Hz

CONTROL UNIT N.O.

COM. E2

A5

RY4

B5 RY3

High B7

N.C.

B9 Low HOOD CAPACITOR

RY6 RY5

OVEN LAMP RELAY
RY1

RY2
SECONDARY INTERLOCK RELAY

DOOR SENSING SWITCH E1 F1 F2
F3

HOOD A1 A3 B1 MOTOR

B3 N.O.

COM.

AH SENSOR

POWER TRANSFORMER
HIGH VOLTAGE CAPACITOR 0.94µF/ AC2300V

HOOD LAMP

HL

OL

TTM

FM

HIGH VOLTAGE RECTIFIER

OVEN LAMP TURNTABLE MOTOR
FAN MOTOR MONITOR SWITCH

PRIMARY INTERLOCK SWITCH
Figure O-2. Oven Schematic-Cooking Condition

MAGNETRON

TROUBLESHOOTING GUIDE

Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is connected.

When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which will be found in the “Test Procedure “section.

IMPORTANT: If the oven becomes inoperative because of a blown monitor fuse, check the monitor switch, relay (RY1) secondary interlock relay (RY2), door sensing switch and primary interlock switch before replacing the monitor fuse. If monitor fuse is replaced, the monitor switch must also be replaced. Use part FFS-BA016/KiT as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases, be necessary to connect the power supply cord after the outer case has been removed, in this event, 1. Disconnect the power supply cord, and then remove
outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor.

4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord. When the testing is completed 1. Disconnect the power supply cord, and then remove
outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Reconnect the leads to the primary of the power
transformer. 5. Reinstall the outer case (cabinet). 6. Reconnect the power supply cord after the outer case is
installed. 7. Run the oven and check all functions.

7

R-1514

TEST PROCEDURE

L Q CK
POSSIBLE CAUSE AND
DEFECTIVE PARTS

CONTROL UNIT AH SENSOR SHORTED OR OPENED WIRING

CONDITION

PROBLEM

The oven stops and “ERROR” is displayed or does not end during Sensor Cooking SENSOR condition. (Oven does not shut off after a cup of water is boiling by Sensor Cooking.)
COOKING
CONDITION Oven stops at 32 seconds after starting.

NOTE: For additional troubleshooting procedures, please refer back to the R-1500/1501/R1505/1506 base model Service Manual.

TEST PROCEDURES

PROCEDURE LETTER

COMPONENT TEST

L

TOUCH CONTROL PANEL ASSEMBLY TEST

The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore, unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and ohmmeter. In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and troubleshooting by unit replacement is described according to the symptoms indicated. Before testing,

Disconnect the power supply cord, and then remove outer case. Refer to procedure of ” HOOD EXHAUST LOUVER REMOVAL “, ” REMOVAL OF OVEN FROM WALL ” and ” OUTER CASE REMOVAL “.
Open the door and block it open. 3) To discharge high voltage capacitor, wait for 60 seconds. 4) Remove two (2) screws holding the hood intake duct R to the ovencavity top plate and the base
plate R. And remove the hood intake duct R. 5) Disconnect the leads to the primary of the power transformer. 6) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape. 1. Key Unit.
NOTE ; 1) Check key unit ribbon connection before replacement. 2) Re-install the hood intake duct R with two (2) screws. 3) Re-install the outer case (cabinet). 4) Reconnect the power supply cord after the outer case is installed. 5) Run the oven and check all functions.
The following symptoms indicate a defective key unit. a) When touching the pads, a certain pad produces no signal at all. b) When touching a number pad, two figures or more are displayed. c) When touching the pads, sometimes a pad produces no signal. If the key unit is defective. 1) Disconnect the power supply cord, and then remove outer case. 2) Open the door and block it open.

8

R-1514

TEST PROCEDURES

PROCEDURE LETTER

COMPONENT TEST

To discharge high voltage capacitor, wait for 60 seconds. 4) Replace the key unit. 5) Reconnect all leads removed from components during testing. 6) Re-install the outer case (cabinet). 7) Reconnect the power supply cord after the outer case is installed. 8) Run the oven and check all functions. 2. Control Unit. The following symptoms indicate a defective control unit. Before replacing the control unit, perform the Key unit test (Procedure M) to determine if control unit is faulty. 2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal. b) When touching the pads, no pads produce a signal. 2-2 In connection with indicators a) At a certain digit, all or some segments do not light up. b) At a certain digit, brightness is low. c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure appears. f) A certain group of indicators do not light up. g) The figure of all digits flicker. 2-3 Other possible problems caused by defective control unit. a) Buzzer does not sound or continues to sound. b) Clock does not operate properly. c) Cooking is not possible. When testing is completed, 1) Disconnect the power supply cord. 2) Open the door and block it open. 3) To discharge high voltage capacitor, wait for 60 seconds. 4) Reconnect all leads removed from components during testing. 5) Re- install the hood intake duct R. 6) Re-install the outer case (cabinet). 7) Reconnect the power supply cord after the outer case is installed. 8) Run the oven and check all functions.

M

KEY UNIT TEST

1. Disconnect the power supply cord. 2. Open the door and block it open. 3. To discharge high voltage capacitor, wait for 60 seconds. 4. Remove the control panel assembly. 5. If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch operates properly; that is the contacts are closed when the door is closed and open when the door is open. If the door sensing switch is good, disconnect the flat ribbon cable that connects the key unit to the control unit and make sure the door sensing switch is closed (either close the door or short the door sensing switch connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method may be used (after clearing the control unit) to determine if the control unit or key pad is at fault. 6. Reconnect all leads removed from components during testing. 7. Re-install the control panel assembly. 8. Reconnect the power supply cord. 9. Run the oven and check all functions.

9

R-1514

PROCEDURE LETTER

G12 G11 G10 G 9

TEST PROCEDURES

COMPONENT TEST

G 8

G 7

G 6

G 5

G 4

G 3

HOT WATER

FRESH ROLLS / MUFFINS

2

DEFROST CUSTOM CENTER HELP

KEEP

SENSOR

WARM REHEAT

4

COOK POPCORN

5

PLUS

CENTER

BAKED POTATOES

7

FRESH VEGETABLES

8

1

POWER LEVEL

FROZEN BEVERAGE ROLLS /
MUFFINS

0

G 2

G 1

3
6
9
TIMER CLOCK

LIGHT HI / LO
FAN HI / LO
STOP CLEAR
START MINUTE
PLUS

N

RELAY TEST

1. Disconnect the power supply cord, and then remove outer case. Refer to procedure of ” HOOD EXHAUST LOUVER REMOVAL “, ” REMOVAL OF OVEN FROM WALL ” and ” OUTER CASE REMOVAL “.
2. Open the door and block it open. 3. To discharge high voltage capacitor, wait for 60 seconds. 4. Remove the hood intake duct R. 5. Disconnect the leads to the primary of the power transformer. 6. Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape. 7. After that procedure, re-connect the power supply cord. 8. Check voltage between normal open terminal of the relay RY2 and the normal open terminal of the
relay RY1 on the control unit with an A.C. voltmeter. The meter should indicate 120 volts, if not check oven circuit. RY1, RY2, RY3, RY4, RY5 and RY6 Relay Test These relays are operated by D.C. voltage Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated ………………… Defective relay. DC. voltage not indicated …………… Check diode which is connected to the relay coil. If diode is
good, control unit is defective.

RELAY SYMBOL RY1 RY2(COOK) RY3 RY4 RY5 RY6

OPERATIONAL VOLTAGE Approx. 25.0V D.C. Approx. 24.5V D.C. Approx. 25.0V D.C. Approx. 25.0V D.C. Approx. 25.0V D.C. Approx. 25.0V D.C.

CONNECTED COMPONENTS Oven lamp / Fan motor / Turntable motor Power transformer Hood motor Hood motor Hood lamp Hood lamp

9. Disconnect the power supply cord. 10. Open the door and block it open. 11. To discharge high voltage capacitor, wait for 60 seconds. 12. Reconnect all leads removed from components during testing. 13. Re-install the hood intake duct R. 14. Re-install the outer case (cabinet). 15. Reconnect the power supply cord after the outer case is installed.

O

DEFROST CENTER TEST

(1) Open the door. (2) Place one cup of water in the center of the turntable tray in the oven cavity. (3) Touch the ” DEFROST CENTER ” pad once. And then touch the number pad ” 2 “. (4) Touch the number pad ” 5 “. (5) Close the door. (6) Touch the ” START ” button. (7) The oven is in Defrost center cooking condition.
10

R-1514

TEST PROCEDURES

PROCEDURE LETTER

(8) The oven will operate as follows.

Menu

1ST STAGE

Steaks/Chops LEVEL TIME

0.5lbs

60% 57sec.

COMPONENT TEST
2ND STAGE LEVEL TIME
40% 17sec.

(9) If improper operation is indicated, the control unit is probably defective and should be checked.

P

FOIL PATTERN ON THE PRINTED WIRING BOARD TEST

To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on the PWB, this foil pattern acts as a fuse. 1. Foil pattern check and repairs.

Disconnect the power supply cord. 2) Open the door and block it open. 3) To discharge high voltage capacitor, wait for 60 seconds. 4) Remove the control unit, referring to the procedure of ” CONTROL PANEL ASSEMBLY,
CONTROL UNIT AND KEY UNIT REMOVAL “. 5) Follow the troubleshooting guide given below for repair.

STEPS
1 2

OCCURRENCE
Only pattern at “a” is broken. Pattern at “a” and “b” are broken.

CAUSE OR CORRECTION
Insert jumper wire J1 and solder. Insert the coil RCILF2003YAZZ between “c” and “d”.

VRS1

Make a visual inspection of the varistor.

Check for burned damage and examine the

1

transformer with a tester for the presence of layer short-circuit (check the primary coil

d

S P

RY2 J1
QKITPB035

resistance which is approximately 780 ±

10%). If any abnormal condition is detected,

replace the defective parts. 7) Reconnect all leads removed from
components during testing.

c ba

T1

3

Re-install the control unit to the control panel

and re-install the control panel to the oven.

Reconnect the power supply cord.
Run the oven and check all functions.

2. Follow the troubleshooting guide given below, if indicator does not light up after above check and

repairs are finished.

Disconnect the power supply cord, and then remove outer case. Refer to procedure of ” HOOD

EXHAUST LOUVER REMOVAL “, ” REMOVAL OF OVEN FROM WALL ” and ” OUTER CASE

REMOVAL “.

Open the door and block it open.
To discharge high voltage capacitor, wait for 60 seconds.
Remove the hood intake duct R.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using

insulation tape.

After that procedure, re-connect the power supply cord.
Follow the troubleshooting guide given below for repair.

STEPS
1 2

OCCURRENCE
The rated AC voltage is not present between the normal open terminal of the relay RY2 and the normal open terminal of the relay RY1.
The rated AC voltage is present at primary side of low voltage transformer.

CAUSE OR CORRECTION
Check supply voltage and oven power cord.
Low voltage transformer or secondary circuit defective. Check and repair.

11

R-1514

PROCEDURE LETTER

TEST PROCEDURES
COMPONENT TEST
9) Disconnect the power supply cord. 10) Open the door and block it open. 11) To discharge high voltage capacitor, wait for 60 seconds. 12) Reconnect all leads removed from components during testing. 13) Re-install the hood intake duct R. 14) Re-install the outer case (cabinet). 15) Reconnect the power supply cord after the outer case is installed. 16) Run the oven and check all functions.

Q

AH SENSOR TEST

Checking the initial sensor cooking condition WARNING : The oven should be fully assembled before following procedure. (1) The oven should be plugged in at least two minutes before sensor cooking. (2) Room temperature should not exceed 95°F (35°C). (3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION INSTRUCTIONS” of the operation manual. (4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To permit adequate ventilation, be sure to install so as not to block these vents. There should be some space for air circulation. (5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture with a dry cloth or paper towel. (6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be at refrigerator temperature and canned soup at room temperature. (7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The sensor will detect the vapor given of by the spray and turn off before food is properly cooked. (8) If the sensor has not detected the vapor of the food, ERROR will appear and the oven will shut off.
Water load cooking test WARNING : The oven should be fully assembled before following procedure. Make sure the oven has been plugged in at least two minutes before checking sensor cook operation. The cabinet should be installed and screws tightened. (1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup. (2) Place the container on the center of tray in the oven cavity. (3) Close the door. (4) Touch the TIMER/CLOCK once, the POWER LEVEL pad twice, the START pad once, the number
pad 1 once and the number pad 4 once. Now, the oven is in the sensor cooking condition, and ” AH20 “, ” SENSOR ” and ” COOK ” will appear in the display. (5) The oven will operate for the first 32 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opened or STOP/CLEAR pad is touched during first stage of sensor cooking.
(6) After approximately 32 seconds, microwave energy is produced.
If ERROR is displayed or the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below. If the oven stops after 5 minutes and ERROR is displayed, the AH sensor is normal. Check other parts except the AH sensor.

TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor. (1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Remove the AH sensor. (5) Install the new AH sensor. (6) Reconnect all leads removed from components during testing.

12

R-1514

TEST PROCEDURES

PROCEDURE LETTER

COMPONENT TEST

(7) Re-install the outer case (cabinet). (8) Reconnect the power supply cord after the outer case is installed. (9) Reconnect the oven to the power supply and check the sensor cook operation as follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup. 9-2. Place the container on the center of tray in the oven cavity. 9-3. Close the door. 9-4. Touch the TIMER/CLOCK pad once, the POWER LEVEL pad twice, the START pad once, the
number pad 1 once and the number pad 4 once. 9-5. The control panel is in automatic Sensor operation. 9-6. The oven turns off automatically, and the time for detecting moisture will be displayed. If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation below.
CHECKING CONTROL UNIT
(1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Disconnect the sensor connector that is mounted to control panel. (5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel. (6) Disconnect the leads to the primary of the power transformer. (7) Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape. (8) After that procedure, re-connect the power supply cord. (9) Check the sensor cook operation proceed as follows:
9-1. Touch the TIMER/CLOCK pad once, the POWER LEVEL pad twice, the START pad once and the number pad 1 once and the number pad 4 once.
9-2. The control panel is in the sensor cooking operation. 9-3. After approximately 65 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor. 9-4. After approximately 3 seconds, the display shows ” X X . X X ” which is the time for detecting
moisture. If the above is not the case, the control unit is probably defective. If the above is proper, the AH sensor is probably defective. (10) Disconnect the power supply cord, and then remove outer case. (11) Open the door and block it open. (12) Discharge high voltage capacitor. (13) Disconnect the dummy resistor circuit from the sensor connector of control panel. (14) Carry out necessary repair. (15) Reconnect all leads removed from components during testing and repairing. (16) Re-install the outer case (cabinet). (17) Reconnect the power supply cord after the outer case is installed. Run the oven and check all functions. (18) Carry out “Water load cooking test” again and ensure that the oven works properly.

R1, R2 : 22 ± 1% 1/2W R3 : 4.3k ± 5% 1/4W R4 : 1M ± 5% 1/4W

Plunger
NC NO

To connector (F) on Control Unit.

1

F-1

2

F-2

3

F-3

CONNECTOR

R1 R2 R3 R4

COM COM NO
NC

Sensor Dummy Resistor Circuit

13

R-1514

TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL

The touch control section consists of the following units as shown in the touch control panel circuit.

(1) Key Unit (2) Control Unit (The Control unit consists of LSI Unit and
Power U nit)

The principal functions of these units and the signals communicated among them are explained below.

Key Unit The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P20, P21, P22, P23, P24, P25, P26 and P27. When a key pad is touched, a signal is completed through the key unit and passed back to the LSI through P43, P44, P45 and P46 to perform the function that was requested.

Control Unit Control unit consists of LSI, power source circuit, synchronizing signal circuit, reset circuit, buzzer circuit, relay circuit indicator circuit, back light circuit and absolute humidity sensor circuit.

LSI This LSI controls the key strobe signal, relay driving signal for oven function and indicator signal.
Power Source Circuit This circuit generates voltages necessary for the control unit from the AC line voltage. In addition, the synchronizing signal is available in order to compose a basic standard time in the clock circuit.

Symbol VC

Voltage -5.3V

Application LSI(IC1)

Synchronizing Signal Circuit The power source synchronizing signal is available in order to compose a basic standard time in the clock circuit. It incorporates a very small error because it works on commercial frequency.
Reset Circuit A circuit to generate a signals which resetting the LSI to the initial state when power is applied.
Buzzer Circuit The buzzer is responds to signals from the LSI to emit audible sounds (key touch sound and completion sound).
Door Sensing Switch A switch to inform the LSI if the door is open or closed.
Relay Circuit To drive the magnetron, fan motor, turntable motor, hood motor, and light the oven lamp and hood lamp.
Indicator Circuit This circuit consists of 25 segments and 4 common electrodes using a Light Crystal Display.
Back Light Circuit A circuit to drive the back light (Light emitting diodes LD1-LD4).
Absolute Humidity Sensor Circuit This circuit detects moisture of the cooking food to allow its automatic cooking.

DESCRIPTION OF LSI

LSI The I/O signal of the LSI is detailed in the following table.

Pin No. Signal

I/O

1-2 VL2-VL1 IN

3-6 AN7-AN4 IN

7

AN3

OUT

8

AN2

IN

9

AN1

IN

Description
Power source voltage input terminal. Standard voltage for LCD.
Terminal to change cooking input according to the Model. By using the A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to set up its cooking constant.
Back light circuit (Light emitting diodes) driving signal.
To input signal which communicates the door open/close information to LSI. Door close “H” level signal (0V). Door open “L” level signal (-5V).
AH sensor input.. This input is an analog input terminal from the AH sensor circuit, and connected to the A/D converter built into the LSI.

14

R-1514

Pin No. Signal

10

AN0

11-13 14

P57-P55 CNTR0

15

P53

16

P52

17

P51

18

P50

19

P47

20

P46

21

P45

22

P44

23

P43

24

INT0

25 26 27
28-29 30

P41 P40 RESET
P71-P70 XIN

31

XOUT

32

VSS

33

P27

I/O IN
OUT OUT
OUT OUT
OUT OUT OUT
IN
IN IN IN IN
OUT IN IN
OUT IN
OUT IN
OUT

Description

Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an analog input terminal from the AH sensor circuit, and connected to the A/D converter built into the LSI.

Used for initial balancing of the bridge circuit (absolute humidity sensor).

Signal to sound buzzer (2.0 kHz). A: key touch sound. B: Completion sound.

0.1 sec. A
2.0 sec. B

H : GND L : -5V H : GND L : -5V

Used for initial balancing of the bridge circuit (absolute humidity sensor).

Oven lamp, fan motor and turntable motor driving signal

To turn on and off shut off relay (RY1). The square waveform voltage is delivered to the RY1 driving circuit and RY2 control circuit.

16.7 msec.

During cooking

H : GND L : -5V

Used for initial balancing of the bridge circuit (absolute humidity sensor).

Terminal not used.

Magnetron high-voltage circuit driving signal. OFF

To turn on and off the cook relay (RY2). The Maximum

signals holds “L” level during microwave output

ON

cooking and “H” level while not cooking. In

OFF

other cooking modes (variable cooking) the signal turns to “H” level and “L” level in

70% of maximum 24 sec.

output

ON

8 sec.

repetition according to the power level.

H : GND L : -5V H : GND
L : -5V

Signal coming from touch key. When either G12 line on key matrix is touched, a corresponding signal out of P20 – P27 will be input into P46. When no key is touched, the signal is held at “H” level.
Signal similar to P46. When either G11 line on key matrix is touched, a corresponding signal will be input into P45.

Signal similar to P46. When either G10 line on key matrix is touched, a corresponding signal will be input into P44.

Signal similar to P46. When either G9 line on key matrix is touched, a corresponding signal will be input into P43.

Signal synchronized with commercial power source frequency.

This is the basic timing for time processing of LSI.

H : GND

16.7 msec.

L : -5V

Terminal not used. Connected to GND through the pull-down resistor R100.
Auto clear terminal. Signal is input to reset the LSI to the initial state when power is applied.
Terminal not used. Internal clock oscillation frequency input setting. The internal clock frequency is set by inserting the ceramic filter oscillation circuit with respect to XOUT terminal.
Internal clock oscillation frequency control output. Output to control oscillation input of XIN.
Power source voltage: -5.0V. VC voltage of power source circuit input.
Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G8 line keys on key matrix is touched.
15

R-1514

Pin No. Signal

34

P26

I/O OUT

35

P25

OUT

36

P24

OUT

37

P23

OUT

38

P22

OUT

39

P21

OUT

40

P20

OUT

41

P17

OUT

42

P16

OUT

43

P15

OUT

44

P14

OUT

45-47 P13-P11 OUT 48-72 SEG24-SEG0 OUT

73/74 75 76

VCC/VREF AVSS COM3

IN IN OUT

Description

Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G7 line keys on key matrix is touched.

Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G6 line keys on key matrix is touched.
Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G5 line keys on key matrix is touched.

Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G4 line keys on key matrix is touched.

Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G3 line keys on key matrix is touched.
Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G2 line keys on key matrix is touched.

Key strobe signal. Signal applied to touch-key section. A pulse signal is input to P43-P46 terminal while one of G1 line keys on key matrix is touched.

Hood lamp driving signal.

To turn on and off relay(RY6). “L” level: During

Hood lamp ON. “H” level: During Hood lamp OFF.

ON

Hood lamp driving signal.

To turn on and off relay(RY5). “L” level: During

Hood lamp ON. “H” level: During Hood lamp OFF.

ON

Hood motor high / low driving signal.

To turn on and off relay(RY3). “L” level: During Hood

motor high. “H” level: During Hood motor low.

ON

OFF

H : GND L

OFF

H : GND L

OFF

H : GND L

Hood motor driving signal.

To turn on and off relay(RY4). “L” level: During

Hood motor ON. “H” level: During Hood motor OFF.

ON

Terminal not used.

Segment data signal. Connected to LCD.

OFF

H : GND L

The relation between signals are as follows:

LSI signal (Pin No.) LCD (Pin No.) SEG 24 (48) —————- SEG24 (29) SEG 23 (49) —————- SEG23 (28) SEG 22 (50) —————- SEG22 (27) SEG 21 (51) —————- SEG21 (26) SEG 20 (52) —————- SEG20 (25) SEG 19 (53) —————- SEG19 (24) SEG 18 (54) —————- SEG18 (23) SEG 17 (55) —————- SEG17 (22) SEG 16 (56) —————- SEG16 (21) SEG 15 (57) —————- SEG15 (20) SEG 14 (58) —————- SEG14 (19) SEG 13 (59) —————- SEG13 (18) SEG 12 (60) —————- SEG12 (17)

LSI signal (Pin No.)

LCD (Pin No.)

SEG 11 (61) —————— SEG11 (16)

SEG 10 (62) —————— SEG10 (15)

SEG 9 (63) —————— SEG 9 (14)

SEG 8 (64) —————— SEG 8 (13)

SEG 7 (65) —————— SEG 7 (12)

SEG 6 (66) —————— SEG 6 (11)

SEG 5 (67) —————— SEG 5 (10)

SEG 4 (68) —————— SEG 4 ( 9)

SEG 3 (69) —————— SEG 3 ( 8)

SEG 2 (70) —————— SEG 2 ( 7)

SEG 1 (71) —————— SEG 1 ( 6)

SEG 0 (72) —————— SEG 0 ( 5)

Connected to GND. Connected to VC.

Common data signal.

Connected to LCD signal COM4.

16

Pin No. 77 78 79 80

Signal COM2 COM1 COM0
VL3

I/O OUT OUT OUT
IN

Description

Common data signal.

Connected to LCD signal COM3.

Common data signal.

Connected to LCD signal COM2.

Common data signal.

Connected to LCD signal COM1.

Power source voltage input terminal.

Standard voltage for LCD.

R-1514

ABSOLUTE HUMIDITY SENSOR CIRCUIT

(1) Structure of Absolute Humidity Sensor The absolute humidity sensor includes two thermistors as shown in the illustration. One thermistor is housed in the closed vessel filled with dry air while another in the open vessel. Each sensor is provided with the protective cover made of metal mesh to be protected from the external airflow.

ventilation opening for sensing

Thermistors

Sensing part (Open vessel)

Sensing part (Closed vessel)

(2) Operational Principle of Absolute Humidity Sensor The figure below shows the basic structure of an absolute humidity sensor. A bridge circuit is formed by two thermistors and two resistors (R1 and R2). The output of the bridge circuit is to be amplified by the operational amplifier. Each thermistor is supplied with a current to keep it heated at about 150°C (302°F), the resultant heat is dissipated in the air and if the two thermistors are placed in different humidity conditions they show different degrees of heat conductivity leading to a potential difference between them causing an output voltage from the bridge circuit, the intensity of which is increased as the absolute humidity of the air increases. Since the output varies by minute, it is amplified by the operational amplifier.

C
S R3

Operational R1 amplifier

Output

voltage

R2

S : Thermistor

open vessel

C : Thermistor closed vessel

Absolute humidity vs, output voltage characteristic
Absolute humidity (g/m 2)

(3) Detector Circuit of Absolute Humidity Sensor Circuit This detector circuit is used to detect the output voltage of the absolute humidity circuit to allow the LSI to control sensor cooking of the unit. When the unit is set in the sensor cooking mode, 16 seconds clearing cycle occurs

Output voltage R90
C90 0.1 uF
C93 C91 0.01uF
0.015uF C92
0.01uF

then the detector circuit starts to function and the LSI observes the initial voltage available at its AN1 terminal. With this voltage given, the switches SW1 to SW5 in the LSI are turned on in such a way as to change the resistance values in parallel with R98 ~ R102 of IC2. Changing the resistance values results in that there is the same potential at both F-3 terminal of the absolute humidity sensor and AN0 terminal of the LSI. The voltage of AN1 terminal will indicate about -2.5V. This initial balancing is set up about 16 seconds after the unit is put in the Sensor Cooking mode. As the sensor cooking proceeds, the food is heated to generate moisture by which the resistance balance the bridge circuit is deviated to increase the voltage available at AN1 terminal of the LSI. Then the LSI observes that voltage at AN1 terminal and compares it with its initial value, and when the comparison rate reaches the preset value (fixed for each menu to be cooked), the LSI causes the unit to stop sensor cooking; thereafter, the unit goes in the next operation automatically. When the LSI starts to detect the initial voltage at AN1 terminal 16 seconds after the unit has been put in the Sensor Cooking mode, if it is not possible to balance, of the bridge circuit due to disconnection of the absolute humidity sensor, ERROR will appear on the display and the cooking is stopped.

Absolute humidity sensor circuit

C. Thermistor in closed vessel
S. Thermistor in open vessel

R98 R99 R100 R101 R102

620k 300k 150k 75k 37.4k

R97 47k

F-1

C

R96

F-3 3.57k

S F-2

R91 3.32k

R92

1.8k

R94

IC2

10k

R93 360k

R95 47k
D90

11

SW1 P57

12

SW2

P56

13

SW3

P55

17

SW4

P51

15

SW5 P53

10 AN0
LSI (IC1)

9 AN1

VA : -15V

VA : -15V VC : -5V

17

R-1514

SERVICING

1. Precautions for Handling Electronic Components This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the surrounding high voltage power source, static electricity charge in clothes, etc. and sometimes it is not fully protected by the built- in protection circuit. In order to protect CMOS LSI.

When storing and transporting, thoroughly wrap them in aluminium foil. Also wrap all PW boards containing them in aluminium foil.
When soldering, ground the technician as shown in the figure and use a grounded soldering iron and work table.
approx. 1M ohm

2. Shapes of Electronic Components

Transistor 2SB1238

B C E

Transistor KRC243M
E CB

3. Servicing of Touch Control Panel

We describe the procedures to permit servicing of the

touch control panel of the microwave oven and the

precautions you must take when doing so. To perform

the servicing, power to the touch control panel is available

either from the power line of the oven itself or from an

external power source.

(1) Servicing the touch control panel with power supply

of the oven:

CAUTION:

THE HIGH VOLTAGE TRANSFORMER OF THE

MICROWAVE OVEN IS STILL LIVE DURING

SERVICING AND PRESENTS A HAZARD.

Therefore, before checking the performance of the touch

control panel,

Disconnect the power supply cord, and then remove

outer case.

Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power

transformer.

Ensure that these leads remain isolated from other

components and oven chassis by using insulation

tape.

After that procedure, re-connect the power supply

cord.

After checking the performance of the touch control panel,

Disconnect the power supply cord.
Open the door and block it open.
Re-connect the leads to the primary of the power

transformer.

Re-install the outer case (cabinet).
Re-connect the power supply cord after the outer case is installed.
Run the oven and check all functions. A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the two can’t be separated. For those models, check and repair all the controls (sensor-related ones included) of the touch control panel while keeping it connected to the oven. B. On some models, the power supply cord between the touch control panel and the oven proper is long enough that they may be separated from each other. For those models, it is possible to check and repair the controls of the touch control panel while keeping it apart from the oven proper; in this case you must short both ends of the door sensing switch (on PWB) of the touch control panel with a jumper, which activates an operational state that is equivalent to the oven door being closed. As for the sensor-related controls of the touch control panel, checking them is possible if dummy resistor(s) with resistance equal to that of the controls are used. (2) Servicing the touch control panel with power supply from an external power source: Disconnect the touch control panel completely from the oven proper, and short both ends of the door sensing switch (on PWB) of the touch control panel, which activates an operational state that is equivalent to the oven door being closed. Connect an external power source to the power input terminal of the touch control panel, then it is possible to check and repair the controls of the touch control panel it is also possible to check the sensor-related controls of the touch control panel by using the dummy resistor(s).
4. Servicing Tools Tools required to service the touch control panel assembly.
Soldering iron: 30W (It is recommended to use a soldering iron with a grounding terminal.)
Oscilloscope: Single beam, frequency range: DC-10MHz type or more advanced model.
Others: Hand tools
5. Other Precautions 1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static electricity. 2) Connect the connectors of the key unit to the control unit being sure that the lead wires are not twisted. 3) After aluminium foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied to the input or output terminals. 4) Attach connectors, electrolytic capacitors, etc. to PWB, making sure that all connections are tight. 5) Be sure to use specified components where high precision is required.

18

R-1514

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

WARNING AGAINST HIGH VOLTAGE:

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in severe, possibly fatal, electric shock. (Example) High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..

WARNING:

Avoid possible exposure operating the oven.

to

microwave

energy.

Please

follow

the

instructions

below

before

1. Disconnect the power supply cord. 2. Make sure that a definite” click” can be heard when the
microwave oven door is unlatched. (Hold the door in a closed position with one hand, then push the door open button with the other, this causes the latch leads to rise, it is then possible to hear a “click’ as the door switches operate.) 3. Visually check the door and cavity face plate for damage (dents, cracks, signs of arcing etc.).
Carry out any remedial work that is necessary before operating the oven. Do not operate the oven if any of the following conditions exist;

1. Door does not close firmly. 2. Door hinge, support or latch hook is damaged. 3. The door gasket or seal is damaged. 4. The door is bent or warped. 5. There are defective parts in the door interlock system. 6. There are defective parts in the microwave generating
and transmission assembly. 7. There is visible damage to the oven.
Do not operate the oven: 1. Without the RF gasket (Magnetron). 2. If the wave guide or oven cavity are not intact. 3. If the door is not closed. 4. If the outer case (cabinet) is not fitted.

WARNING FOR WIRING

To prevent an electric shock, take the following precautions. 1. Before wiring,

Disconnect the power supply cord. 2) Open the door block it open. 3) Discharge the high voltage capacitor and wait for 60
seconds. 2. Don’t let the wire leads touch to the followiong parts;
High voltage parts: Magnetron, High voltage transformer, High voltage capacitor and High voltage rectifier assembly.
Hot parts: Oven lamp, Magnetron, Power transformer and Oven cavity.
Sharp edge: Bottom plate, Oven cavity, Waveguide flange, Chassis support and other metallic plate.
Movable parts (to prevent a fault) Fan blade, Fan motor, Switch, Open lever, Open button.
3. Do not catch the wire leads in the outer case cabinet. 4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even if the wire leads are pulled. 5. To prevent an error function, connect the wire leads correctly, referring to the Pictorial Diagram.

THE FOLLOWING ADJUSTMENTS OR COMPONENT REPLACEMENT CAN BE PERFORMED WITHOUT REMOVING THE OVEN FROM THE WALL

1. Hood lamps, hood lamp sockets, oven lamp, grease filter and charcoal filter.
2. Base cover and hood lamp glass assembly.

3. Turntable motor. 4. Hood exhaust louver. 5. Control panel assembly or components.

AH SENSOR REMOVAL

1. Disconnect the power supply cord, remove the oven from wall, and remove outer case. (Refer to procedure of “REMOVAL OF OVEN FROM WALL” AND “OUTER CASE REMOVAL”.) And proceed as follows.

2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60
seconds. 4. Remove three (3) screws holding the hood intake duct R

19

R-1514

to the oven cavity top plate, the oven cavity front flange and the fan duct. And remove the hood intake duct R. 5. Disconnect the connector CN-F of AH sensor from the control unit. 6. Remove the two (2) screws and one (1) washer holding the AH sensor to the hood duct L. 7. Release the wire lead of AH sensor from the holes of the hood ducts L and R. 8. Now, the AH sensor is free.
NOTE: When the AH sensor is reinstalled, the wire tie of the AH sensor should be positioned under the hole of the oven cavity top plate (right).

Sensor ground wire Screws Screw

AH sensor Hole Wire lead of AH sensor

Hood duct L

Hole

Hood duct R
Hole Wire tie
This illustration is under the condition which hood intake duct R is removed

CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL

1. Disconnect the power supply cord. 2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60
seconds. 4. Remove three (3) screws holding the hood exhaust
louver to oven cavity front face plate. 5. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver. (Refer to procedure of “HOOD EXHAUST LOUVER REMOVAL”) 6. Remove one (1) screw holding the control panel to the oven cavity front face plate. 7. Release the control panel from the oven cavity front face plate by lifting it up. 8. Disconnect the wire leads from the relays RY1 and RY2. 9. Disconnect the connectors CN-A, CN-B, CN-E and CNF from the control unit. 10. Remove the control panel assembly from the oven. 11.Now, the control panel assembly is free. 12.Disconnect the connector CN-G from the control unit. 13.Remove the two (2) screws holding the LCD holder to the key fixing plate. 14.Remove two (2) screws holding the power unit to the key fixing plate. 15.Release the two (2) tabs holding the power unit to the key fixing plate. 16.Release the three (3) tabs holding the LCD to the LCD holder. 17.Release the two (2) tabs holding the LSI unit to the LCD holder. 18.Remove the LCD holder and the LED sheet. 19.Now, the control unit is free.

20.Remove the one (1) screw holding the key fixing plate to the control panel.
21.Release the six (6) tabs holding the key fixing plate to the control panel.
22.Remove the key fixing plate from the control panel. 23.Remove the key unit from the key fixing plate. 24.Now, the key unit is free NOTES FOR KEY UNIT REPLACEMENT 1. Do not reuse the torn key unit because the performance
of the adhesive becomes weak. 2. Before attaching a new key unit, wipe off remaining
adhesive on the key fixing plate surfaces completely with a soft cloth soaked in alcohol. 3. When attaching the key unit to the key fixing plate, adjust the upper edge and right edge of the key unit to the correct position of key fixing plate. See key unit location. 4. Stick the key unit firmly to the key fixing plate by rubbing with soft cloth not to scratch.
Key unit
Key fixing plate
Key unit location

OVEN LAMP REMOVAL

1. Disconnect the power supply cord. 2. Open the door and block it open. 3. To discharge the high voltage capacitor, wait for 60
seconds.

4. Remove the hood exhaust louver and release the control panel assembly, referring to items 4 to 7 of “CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL”.

20

R-1514

5. Disconnect only the connector CN-F from the control unit. It is not necessary to disconnect other connectors or wire leads from the control unit.
6. Release the oven lamp socket from the magnteron duct

by turning the socket counterclockwise. 7. Remove the oven lamp from the socket by turning the
oven lamp. 8. Now the oven lamp is free.

OVEN LAMP SOCKET REMOVAL

1. Disconnect the power supply cord. 2. Open the door and block it open. 3. Remove three (3) screws holding the hood exhaust
louver to oven cavity front face plate. 4. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver. (Refer to procedure of “HOOD EXHAUST LOUVER REMOVAL”) 5. Remove one (1) screw holding the control panel to the oven cavity front face plate. 6. Release the control panel from the oven cavity front face plate by lifting it up and tilting top edge back. 7. Turn the lamp socket and release it from the magnetron duct.

8. Screw the oven lamp off from the lamp socket. 9. Now, the oven lamp is free. 10.Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with the small flat type screw driver. 11.Now, the oven lamp socket is free.
Oven lamp socket
Terminal Wire lead
Terminal hole
Flat type small screw driver

21

A

B

C

D

E

F

G

H

R-1514

1

2

3

CN-F 1 BLK 2 RED 3 WHT

AH SENSOR

CONTROL UNIT

CN-E 2 GRN 1 RED

N.O. RED

COM.

GRN

DOOR SENSING SWITCH

GRY GRY
WHT WHT
BLK ORG RED
R E D

CN-G

CN-C

CN-F

14

1

CN-C

RY1

COM. N.O.

12 CN-E

N.O.

COM.

T1

RY2:

C100

RY2: SECONDARY INTERLOCK RELAY

RY3 RY4 RY5 RY6

9 CN-B

51 1 CN-A

CN-A 1 RED 2 3 YLW 4 5 PPL

CN-B

1 BRN

2

3

PNK or BLU

4

5 ORG

6

7 BLK 8

9 WHT

BLK BLK
RED N.C.

MONITOR SWITCH

FUSE & HOLDER

RED

WHT WHT
COM.

PRIMARY INTERLOCK SWITCH

COM.

N.O.

WHT WHT
GRY

6 RED 5 RED YLW 4 YLW WHT 3 WHT BLK 2 BLK BLU 1 BLU

HOOD FAN MOTOR

BLK 3 BLK WHT BLU 2 WHT GRN 1 GRN

Power Supply cord 120V 60Hz

RED

BLK RED

BRN
TURNTABLE WHT MOTOR

RED

ORG
HOOD FAN THERMAL CUT-OUT
GRN GRN

BLK PPL
GRN

to Base Plate Right

WHT

Blue Marking

BRN

WHT WHT

PNK or
BLU

HOOD LAMP & SOCKET

RED
CAVITY THERMAL CUT-OUT

Blue Marking
ORG
BRN
GRY
OVEN LAMP & SOCKET

MAGNETRON TEMPERATURE FUSE
WHT RED FAN MOTOR

HIGH VOLTAGE COMPONENTS
MAGNETRON
HIGH VOLTAGE WIRE A

RED WHT WHT

HIGH VOLTAGE CAPACITOR

POWER TRANSFORMER

HIGH VOLTAGE RECTIFIER

22

4

5

6

Figure S-1. Pictorial Diagram

A

B

C

D

E

F

G

H

R-1514

1

2

3

4

5

6

A

T1 15

D1-D4 1N4002

D3

D1

B

10G471K

VRS1

d 3 8 D4 D2 a

(J1)

D21 1SS270A

D22 1SS270A

b

C
AC(N)

c N.O

OVEN LAMP

TURNTABLE

MOTOR

COM

FAN MOTOR

RY1

AC(H)

N.O

D

MICRO.

COM

RY2

HIGH B 7

HOOD MOTOR

LOW B 9

HOOD

RY3

THERMAL

B 5

CUT-OUT

E

HOOD MOTOR COM.

A 5

RY4

D23 1SS270A

D24 1SS270A

D25 1SS270A

HOOD LAMP B 3 RY5
CN-B
F

D26 1SS270A

HOOD LAMP B 1

A 3

RY6

C100 7µ/230v

MOTOR RUN CAPACITOR
A 1

CN-A

G

NOTE

: IF NOT SPECIFIED, 1/4W ± 5%

C1 0.1µ/50v C2 1000µ/35v
R3 2.4k
ZD1 HZ16-1 C3 10µ/35v

E2 E1
R30 3.3k

C 1 GND

B

C 7 VC Q1 2SB1238 R2 510 1/2w

C 3 VA

R1 270 2w

C 5 INT

C

+

C21 10µ/35v
Q21 KRC243M

OVEN LAMP C12 TURNTABLE
MOTOR FAN MOTOR

SP1 PKM22EPT

C 4 BUZZER

D

C11 MICRO.

C10 HOOD MOTOR H/L

C 9

HOOD MOTOR COM.

C 2 VR

E

C 8 HOOD LAMP

DOOR SENSING SWITCH

C 6 HOOD LAMP

D20

F

1SS270A

C13 Q22

C14
D40 1SS270A

DOOR SENSING SWITCH

CN-C

14pin

CN-E

WIRE HARNESS

G

H 1

Figure S-2. Power Unit Circuit

2

3

4

5

23

H 6

A

B

C

D

E

F

G

H

R-1514

1

2

3

INT GND
VC VR

C10 47µ/16v C11 0.1µ/50v
R4 82 R5 4.7k

C 5 C 1
+
C 7 C 2
LD1 LD2 LD3 LD4

Q2

R6 4.7k

KTA1661

H. MOTOR H / L

C10

H. MOTOR COM.

C 9

H
Q23 DTA143EAK I

HOOD LAMP

C 8

Q24 DTA143EAK G

VA

C 3

HOOD

C 6

LAMP

BUZZER

C 4

Q25 DTA143EAK F
Q26 DTA143EAK

R91 3.32kD

R96

C90 0.1µ/50v 3.57kD

R90 330 1w

R12 15k C13 0.01µ/25v
ZD10 UDZ4.3B R10
1k

C12 0.1µ/50v

CPU UNIT

Q11 DTA143EKA

Q10 2SA1037AK

D90 MA152WA

58

IC2

7 IC2

BA4558 6 4

R94

R95

15k

47k

C91 0.015µ/25v

R92 1.8kF

R93 360kF

R97 47k

R102 37.4kF R101 75kF R100 150kF R99 300k R98 620k

ABCDE

OVEN LAMP

TURNTABLE MOTOR

C12

FAN MOTOR

MICRO.

C11

Q22

C13

DOOR SENSING SWITCH

C14

NOTE :

Q30 DTA143EAK C20 0.1µ/50v
Q21 DTA143EAK
Q22 DTA143EAK
F-1 F-2 F-3 CN-F
: IF NOT SPECIFIED, 1/16W ± 5%

R40 4.7k

R41 15k
C60 330p/50v C61 330p/50v C62 330p/50v C63 330p/50v
R72 270k

C40 0.01µ/25v

R73 270k

R74 270k

R75 270k

R71 15k R70 15k R69 15k R68 15k

C93 0.01µ/25v C92 0.01µ/25v

C14 R11 0.01µ 15k /25v

(J11) 4.7k (J13) 4.7k (J15) 4.7k (J17) 4.7k

(J10) (J12) (J14) (J16)

R15 4.7k R14 R13 4.7k 4.7k

LIQUID CRYSTAL DISPLAY

GND
COOK SENSOR LBS KG DEF HELP

COM1 COM2 COM3 COM4 SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24

1

29

COM0(LCD) COM1(LCD) COM2(LCD) COM3(LCD)

COM1(LCD) COM2(LCD) COM3(LCD) COM4(LCD)

80

1

VL2

VL1

AN7

AN6

AN5 5

AN4

AN3

AN2

AN1

AN0 10

E

P57

D

P56

C

P55

CNTR0

A

P53 15

P52

B

P51

P50

P47 P46 20

P45

P44 P43

INT0

24

25

VL2 COM0 COM1 COM2 COM3 75 AVSS VREF VCC SEG0 SEG1 70 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7

IC1

65

64
SEG8 SEG9 SEG10 SEG11 60 SEG12 SEG13 SEG14 SEG15 SEG16 55 SEG17 SEG18 SEG19 SEG20 SEG21 50 SEG22 SEG23 SEG24 P11 P12 45 P13 P14 P15 P16 P17
41
40

SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
FGH I CF1 CSTS4.00MG03

R100 4.7k
P41 P40 RESET P71 P70 XIN 30 XOUT VSS P27 P26 P25 35 P24 P23 P22 P21 P20
R80 1M

G12 G11 G10 G 9 R67 15k R66 15k R65 15k R64 15k R63 15k R62 15k R61 15k R60 15k

CN-G

G 8

G 7

G 6

G 5

G 4

G 3

HOT WATER
KEEP WARM PLUS

FRESH ROLLS / MUFFINS
REHEAT

2

DEFROST CUSTOM

CENTER

HELP

SENSOR

4

COOK POPCORN

5

CENTER

BAKED POTATOES

7

FRESH VEGETABLES

8

1

POWER LEVEL

FROZEN BEVERAGE ROLLS /
MUFFINS

0

KEY UNIT

G 2

G 1

3
6
9
TIMER CLOCK

LIGHT HI / LO
FAN HI / LO
STOP CLEAR
START MINUTE
PLUS

24

4

5

6

Figure S-3. LSI Unit Circuit

A

B

C

D

E

F

G

H

1 A B C D E F G H
1

MCS M 2 7A 9 4V 0 R
FB035 MR

RY2 J1
QKITPB035MRE0

R30 T1
C21
RY1 0
BFB

R-1514

2

3

4

5

6

A

CN-C

14

1

D40

D21

D20 DIP

R1

B

2

R2

1

2

Q1

E

B

ZD1

SP1

CN-E

R3

C2

C

Q21

E

B

5

C3

1 C1

D1

D3

D

D4 D2

VRS1

1

S P

3

E

8

C100

RY5

D25

D26

F

D24 RY4 D23

RY3
D22 LOT NO.

RY6

5

1

9

1

CN-A

G

CN-B

Figure S-4. Printed Wiring Board

2

3

4

5

25

H 6

R-1514

PARTS LIST

Note: The parts marked “” may cause undue microwave exposure.

The parts marked “*” are used in voltage more than 250V.

“” MARK: PARTS DELIVERY SECTION

REF. NO.

1- 1 * 1- 2
1- 3 1- 4 1- 5 1- 6
1- 7 * 1- 8
1- 9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17
2- 1 2- 2 2- 3 2- 4 2- 5 2- 6 2- 7 2-7-1 2-7-2 2- 8

PART NO.

FH-DZB016MRY0 M RC-QZA234WRE0 M QFS-TA013WRE0 M RMOTDA211WRE0 M RTHM-A070WRE0 M RTHM-0044MRE0 M RTRN-B068MRE0 M RV-MZA288WRE0 M QFSHDB003MRE0 M QSW- MA085WRE0 M FFS-BA016/KIT M FACCDB011MRE0 M QSOCLB006MRE0 M FMOTEA441WRKZ M RMOTEB031MRE0 M RLMPTA068WRE0 M FDTCTA201WRK0 M

LSTY-B024MRP0 M FDIF-B014MRK0 M GDAI-B065MRP0A M FDECAB031MRK0 M GCABUB103MRP0 M TMAPCB067MRR0 M FANGKB009MRY0 M LANGQB016MRP0 M PGLSPB004MRE0 M PCOVPB096MRT0 M

DESCRIPTION
ELECTRIC PARTS
High voltage rectifier assembly High voltage capacitor Temperature fuse 150 C (Magnetron) Turntable motor Thermal cut-out 145 C (Cavity) Thermal cut-out N.O. 60 C (Hood Fan) Power transformer Magnetron Fuse holder Primary interlock and door sensing switches Monitor switch (V-16G-2C25) with fuse (20A) assembly Power supply cord Oven lamp socket and hood lamp sockets Hood fan motor Fan motor Oven lamp and hood lamps AH sensor
CABINET PARTS
Rear stay Hood exhaust louver Base plate R Front panel L Outer case cabinet Schematic diagram Hood lamp glass assembly Hood lamp glass angle Hood lamp glass Base cover

Q’TY CODE
1 AH 1 AP 1 AE 1 AL 1 AF 1 AH 1 BC 1 BK 1 AD 2 AE 1 AF 1 AQ 3 AE 1 BC 1 AR 3 AE 1 AR
1 AE 1 AX 1 AG 1 AT 1 AZ 1 AB 1 AN 1 AG 1 AH 1 AV

3- 1 3- 1A 3- 1B 3- 1C 3- 1D C1 C2 C3 C21 C100 D1-4 D20-26 D40 Q1 Q21 R1 R2 R3 R30 RY1-2 RY3 RY4-6 SP1 T1 VRS1 ZD1 3- 2 3- 2-1

CPWBFB064MRU0 M QCNCMA017JDZZ M QCNCMA448DRE0 M QCNCMA275DRE0 J FW-VZB189MRE0 M RC-KZA087DRE0 J VCEAB31VW108M J VCEAB31VW106M J VCEAB31VW106M J RC- QZB014MRE0 M RH-DZA006PRE0 J VHD1SS270A/-1 J VHD1SS270A/-1 J VS2SB1238//-3 J VSKRC243M//-3 J VRS-B13AA331J J VRD-B12HF511J J VRD-B12EF242J J VRD-B12EF332J J RRLY-A113DRE0 M RRLY-A123DRZZ M RRLY-B004MRE0 M RALM-A014DRE0 J RTRNPB017MRE0 M RH-VZA032DRE0 J VHEHZ161///-1 J FPNLCB420MRK0 M FUNTKB332MRE0 M

CONTROL PANEL PARTS

Control unit

3-pin connector CN-A

5-pin connector CN-B

2-pin connector CN-E

Lead wire harness CN-C

Capacitor

0.1 uF 50V

Capacitor 1000 uF 35V

Capacitor

10 uF 35V

Capacitor

10 uF 35V

Capacitor

7 uF 230V

Diode (1N4002)

Diode (1SS270A)

Transistor (2SB1238)

Transistor (KRC243M)

Resistor

330 ohm 1W

Resistor

510 ohm 1/2W

Resistor

2.4k ohm 1/4W

Resistor

3.3k ohm 1/4W

Relay (DU24D1-1PR(M))

Relay (G5S-1 24V)

Relay (FTR-F3AA024E)

Buzzer (PKM22EPT)

Transformer

Varistor (10G471K)

Zener diode (HZ16-1)

Control panel sub. assembly

Key unit

1 BF 1 AG 1 AF 1 AB 1 AB 1 AB 1 AF 1 AB 1 AB 1 AD 4 AD 7 AA 1 AA 1 AA 1 AB 1 AA 1 AB 1 AA 1 AA 2 AG 1 AG 3 AG 1 AG 1 AS 1 AE 1 AA 1 BB 1 AU

26

REF. NO.
3- 2-2 3- 2-3 3- 2-4 3- 2-5 3- 2-6 3- 3 3- 4 3- 5

PART NO.

FDECAB030MRK0 M JBTN-B138MRF0 M MSPRTA050WRE0 M PSHEPB101MRE0 M PCAP-B007MR10 M LHLD-B018MRF0 M PSHEPB023MRE0 M XEPSD30P10XS0 M

DESCRIPTION
Open button Select button Button spring Button rubber Button cap LCD holder LED sheet Screw; 3mm x 10mm

4- 1 4- 2 4- 3 4- 4 4- 5 4- 6 4- 7 4- 8 4- 9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 4-23 4-24 4-25
5 5- 1 5- 2 5-2-1 5-2-2 5-2-3 5- 3 5- 4 5- 5

OVEN PARTS
LSTPPB038MRF0 M Door stopper FROLPB025MRK0 M Turntable support assembly NTNT- A108WREZ M Turntable tray LBNDKB009MRP0 M Capacitor holder PDUC-B111MRF0 M Magnetron duct MLEVPB016MRF0 M Open lever ***** M Oven cavity (Not replaceable part) PPACGB014MRF0 M Turntable motor packing PHOK-B018MRF0 M Latch hook FANGTB005MRY0 M Unit mounting plate assembly NFANPB006MRE0 M Fan blade LBSHC0037WRE0 M Cord bushing MLEVFB007MRP0 M Mounting lever PDUC- B112MRP0 M Hood intake duct R PCOVPB085MRP0 M Waveguide cover MSPRTA046WRE0 M Latch spring LANGTB055MRP0 M Chassis support PDUC-B115MRF0 M Hood duct R PDUC- B114MRF0 M Hood duct L PDUC-B113MRP0 M Fan duct PDUC-B117MRF0 M Orifice PCUSGB043MRP0 M Transformer cushion PCUSUB045MRP0 M Cushion PCUSUB019MRP0 M Cushion PCUSUB061MRP0 M Cushion
DOOR PARTS
CDORFB317MRK0 M Door assembly FDORFB070MRT0 M Door panel assembly FCOV- B221MRK0 M Door frame assembly LSTPPB023MRF0 M Latch head MSPRTA046WRE0 M Latch spring LSTPPB037MRF0 M Glass stopper GCOVHB044MRF0 M Choke cover PSHEPB021MRE0 M Sealer film XCPSD40P08000 M Screw : 4mm x 8mm

6- 1 6-1-1 6-1-2 6-1-3 6-1-4 6-1-5 6-1-6 6-1-7 6- 2 6- 3 6- 4 6- 5 6- 6 6- 7 6- 8 6- 9 6-10 6-11 6-12 6-13

MISCELLANEOUS
CFZK-B460MRK0 M Installation material assembly LBSHC0040MRE0 M Grommet LX- BZ0195WRE0 M Toggle screw LX-MZB001MRE0 M Cord holder XBRSD50P60000 M Screw : 5mm x 60mm XOTSD40P12000 M Screw : 4mm x 12mm XTSSD50P35000 M Screw : 5mm x 35mm XWHSD50-16300 M Washer TINSEB316MRK0 M Operation manual TINSKB081MRR0 M Top/wall template QW-QZB025MRE0 M High voltage wire A FW-VZB187MRE0 M Main harness TCAUAB041MRR0 M DHHS service caution label TCAUAB045MRR0 M Monitor caution label TCAUAB005MRR0 M Revised DHHS/GRD C/label FW-VZB188MRE0 M Low voltage harness PFIL-B006MRE0 M Charcoal filter PFIL-B002MRE0 M Grease filter FFTA-B005MRK0 M Exhaust damper assembly PCUSUB059MRP0 M Cushion (only for horizontal venting)

27

R-1514

Q’TY
1 1 1 1 1 1 1 5

CODE
AU AD AA AC AC AC AR AB

1 AB 1 AN 1 AM 1 AB 1 AF 1 AD 1 -1 AA 1 AF 1 AS 1 AC 1 AB 2 AC 1 AG 1 AH 2 AB 2 AD 1 AQ 1 AQ 1 AH 1 AC 1 AC 1 AC 1 AC 1 AC
1 BH 1 AW 1 BE 1 AC 1 AB 2 AC 1 AG 1 AE 4 AA

1 AH 1 AC 4 AC 1 AB 2 AA 3 AA 6 AA 2 AA 1 AF 1 AD 1 AT 1 AT 2 AA 1 AA 1 AB 1 AT 1 AE 2 AF 1 AH 1 AC

R-1514

REF. NO.
6-14 6-15
7- 1 7- 2 7- 3 7- 4 7- 5 7- 6 7- 7 7- 8 7- 9

PART NO.

¤

QW-VZB011MRE0 M LANG-B002MRP0 M

LX-CZB004MRE0 M XOTSF40P12000 M XOTSD40P12000 M XHTSD40P08RV0 M LX-CZA038WRE0 M LX-CZ0052WRE0 M LX-WZB003MRE0 M XCBSD30P08000 M LX-BZA041WRE0 M

DESCRIPTION
Sensor ground wire Scale plate
SCREWS,NUTS AND WASHERS
Special screw Screw : 4mm x 12mm Screw : 4mm x 12mm Screw : 4mm x 8mm Special screw Special screw Sensor washer Screw : 3mm x 8mm Special screw

Q’TY CODE
1 AB 2 AD
3 AA 5 AA 26 AA 2 AA 9 AA 2 AA 1 AA 5 AA 5 AA

HOW TO ORDER REPLACEMENT PARTS

To have your order filled promptly and correctly, please furnish the following information.

1. MODEL NUMBER

2. REF. NO. 3. PART NO.

4. DESCRIPTION

Order Parts from the authorized SHARP parts Distributor for your area. Defective parts requiring return should be returned as indicated in the Service Policy.

PACKING AND ACCESSORIES
4-3 TURNTABLE TRAY TOP PAD
DOOR PROTECTOR WRAP COVER

6-15 SCALE PLATE 6-11 GREASE FILTER (x 2)
6-3 TOP / WALL TEMPLATE
6-2 OPERATION MANUAL 6-1 INSTALL MATERIAL ASSEMBLY 6-12 EXHAUST DAMPER
ASSEMBLY
ACCESSORY PACK

BOTTOM PAD
Non-replaceable items
PACKING CASE
28

R-1514

1

2

3

4

5

6

OVEN AND CABINET PARTS
A

6-1-5

6-12

A