Ramset CableMaster C Plus PulsaLift 800 Plus User Guide

: June 13, 2024
: Ramset

Table of Contents

Ramset CableMaster C Plus PulsaLift 800 Plus
Product Information
Product Usage Instructions
INSTALLATION
OPERATION
COMPONENTS
Application Type
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Ramset CableMaster C Plus PulsaLift 800 Plus

Ramset-CableMaster C-Plus-PulsaLift-800-Plus-product

Product Information

The CableMasterTM 800 Plus is a versatile tool designed for various applications related to cable management. It is compatible with a range of consumables, allowing users to efficiently secure and fix cables in different scenarios. The PulsaLiftTM 800 Plus Pole System is an optional accessory for the CableMasterTM 800 Plus, providing extended reach and ease of use.

Compatible Consumables

Consumable	Application Type
ClipElecTM	Data Cable Strap, Plates & Fixtures
DataLecTM Clip	Data Cable Strap, Plates & Fixtures
CTClipTM	Data Cable Strap, Plates & Fixtures
Threaded Rod Hanger	Light Duty Cable Tray
Direct Alignment Half Saddle	Cable Fixing Small Diameter Rigid Pipes
Strap & Plate Mounting Washer	Cable Fixing Small Diameter Rigid Pipes
Catenary Wire Bracket	Catenary Wire
Clip CTClipTM	Metal Pipes
RamsetTM Australia	Metal/Nylon Straps Fire & Service Cabling

Product Usage Instructions

PulsaLiftTM 800 Plus Pole System Operation:

Load the tool into the pole system, avoiding applying pressure to the trigger while doing so.
Hold the pole and tool vertically upwards.
Push the tool against the work surface to close the fastener guide of the tool.
Use the trigger on the pole to apply more pressure to the work surface and fire the tool.

CableMasterTM 800 Plus Cradle Installation:

Components:

CradleCM800PLUS – Cradle only

Description:

The PulsaLiftTM 800 Plus cradle consists of two elements: the cup and the retaining bolt, which are tethered together with a steel cable.

Place the back of the tool (black cap first) into the cup, ensuring that the tool is fully seated.
Press the button of the retaining bolt to disengage the ball bearings. Push the retaining bolt through the holes in the cage provided over the trigger. Release the retaining bolt button, ensuring that the ball bearings have engaged on the other side of the holes.
Depending on the application height, choose whether the extension pole is required or just the triggering pole.

Compatible Accessories:

V4-3 – 0.9 metre (3 foot) Pole with Trigger
V4-EXT PL800PLUS – 0.9 metre (3 foot) Extension Pole without Trigger
Complete Kit (Tool not included)

Note: CRADLECM800PLUS is compatible with the CM800PLUS and CMCPLUS tool.

Safety Warning:

Never hold onto the triggering section of the pole while loading clips or fasteners into the tool. Inadvertent activation can result in severe injury. Only ever fire the tool overhead while using the pole system.

Important Disclaimer:
Any engineering information or advice (“Information”) provided by Ramset™ in this document is issued in accordance with a prescribed standard, published performance data or design software. It is the responsibility of the user to obtain its own independent engineering (or other) advice to assess the suitability of the Information for its own requirements. To the extent permitted by law, Ramset ™ will not be liable to the recipient or any third party for any direct or indirect loss or liability arising out of, or in connection with, the Information

Use your CableMaster™ C-Plus® or CableMaster™ 800 Plus with the flexible PulsaLift™ Plus Pole System for complete overhead installation without the need for scissor lift equipment $Ramset-CableMaster C-Plus-PulsaLift-800-Plus- fig- $3$$

Permanent cable suspension to concrete & steel
Pipe suspension to concrete & steel
Fire & security cabling
Temporary cable suspension

$Ramset-CableMaster C-Plus-PulsaLift-800-Plus-fig- $4$$

CableMaster™ 800 Plus cradle insert Part Number L1 and R1 (pictured in orange).
CableMaster™ C-Plus® cradle insert Part Number LHINSERT (pictured in orange ).

INSTALLATION

The PulsaLift™ 800 Plus cradle consists of 2 elements: the cup and the retaining bolt (tethered to the cup with a steel cable). $Ramset-CableMaster C -Plus-PulsaLift-800-Plus-fig- $5$$

Place the back of the tool (black cap first) into the cup. Make sure that the tool is fully seated.
Press the button of the retaining bolt (to disengage the ball bearings) and push the retaining bolt through the holes in the cage provided over the trigger. Release the retaining bolt button while making sure that the ball bearings have engaged on the other side of the holes.
Depending upon the application height, choose whether the extension pole is required or just the triggering pole

OPERATION

Load the tool (avoid applying pressure to the trigger when doing so).
Hold the pole and tool vertically upwards.
Push the tool against the work surface to close the fastener guide of the tool.
Use the trigger on the pole to apply more pressure to the work surface to fire the tool.

$Ramset-CableMaster C-Plus-PulsaLift-800-Plus-fig- $6$$

COMPONENTS

CRADLECM800PLUS is compatible with the CM800PLUS and CMCPLUS tool.

SAFETY WARNING
Never hold onto the triggering section of the pole whilst loading clips or fasteners into the tool. Inadvertent activation can result in severe injury. Only ever fire the tool overhead while using the pole system.