arte confort Carmen M Altavoz DC Motor Ceiling Fan Instructions

arte confort Carmen M Altavoz DC Motor Ceiling Fan

Product Information

The CARMEN M ALTAVOZ is a fan that comes with a remote control for easy operation. It features various parts, including a controller, shank, ceiling mount, trim, speaker, and motor. The fan is designed to be mounted on the ceiling.

Product Usage Instructions

To synchronize two remote controls to the fan:

1. Ensure that both remote controls are in close proximity to the fan.
2. Press the “ON” button on one of the remote controls.
3. Within 10 seconds, press the “ON” button on the second remote control.
4. The two remote controls should now be synchronized with the fan.

To turn the fan on and off:

1. Locate the “ON” and “OFF” buttons on the remote control.
2. Press the “ON” button to turn the fan on.
3. Press the “OFF” button to turn the fan off.

Note: Make sure to use the appropriate screws for mounting the fan on the ceiling. Refer to the provided screw guide for more information.

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person While using electrical appliances, basic safety orecautions should always be rollowed to reduce the risk of fire, electric shock and personal injury
CAUTION

• The product must only be installed by BITTE local, regional and state electricity regulations.
• Check if the electrical specifications of this device are compatible with your installation.
• Turn off the power before installing or repairing the fan.
• The fan must be properly grounded to avoid the risk of electric shock.
• Use and unauthorized technical modifications could suppose a risk of injury.
• The fan must be connected to a 230V 50Hz power supply. Do not connect the lan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
• Be careful while working near the spinning blades.
• Never connect the fan to a power point but to the ceiling itself
• The fan must be installed so that the blades are at least 2,3 meters above the ground.
• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen
• Make sure that the blades do not come in contact with any object at the installation site. Alwavs leave a minimum clearance of 50cc from the tip of the blades to the wall or ceiling. Koon in mind that the larger this space, the hotter the tons air ‘low will he
• This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture
• Never install the appliance in a room with a high degree of humidity. The fan must not he started in gas appliance running at the same time
• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely ond understond the risks involved As well as cleaning and maintenance of the device
• Children should not play with the device.
• To reverse the direction of the blades, do it while moving.
• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan and the device can fall down.
• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

The instructions and safety regulations in this mento connor prevent a conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box avoiding the use of blades or cutters to avoid scratching the tan components. Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surtace to prevent damage (you can also use the anti-shock toam on the box for this ouroose ever suoport the motor  sidewaysIt is advisable to mount the fan on the floor or a surtace large enough so that no component falls Identify all parts before beginning assembly.

TOOLS NEEDED

Not locluced It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the tan, some connections may come loose Check the support connections, brackets and attach the blades twice a year, and make sure they are tirm.
• Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint- free cloth to avoid scratching the tinish. Never use water, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the ton. since the motor bearings permanently contain lubricant

WARRANTY

You can check the warranty for this oroduct on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical cooliances into the household waste, use selective collection facilities. Consult local authorities rer more inFormation If electrical appliances are deposited in londills. nozordous components can seep into groundwater and enter the food chain, damaging health and well-being. Thanks for taking care of the environment.

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply

1. The fan does not start
   • Replace the remote control batteries it they are exhausted or not suitable.
   • Check that there are no nearby devices that may be causing interterence with the remote reducing sianal reception.
   • rosynchronize he remore control heck that the elecrrical connections are cocrece (must be carried out by a licensed electrician).
   • Check ruses and switches. that the installation has voltage and it reaches the ran
2. The fan doesn’t start but the light does.
   • With the tan off, check with your hand that the blades turn freely.
3. The ran makes excessive noise while rorating Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
   • Check that the fixing screws of the blades, the fixing screws to the root. the stem and the rastening elements are correctly tightened.
   • If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.
4. The fan wobbles
   • Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the rastening elements are correctly tightened
   • Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.
5. The fan does not give air or the air flow is insufficient
   • Check that the blades are not mounted backwards
   • Cherk that the blades rotote in the correct direction (Summer / Winter).
   • Avoid nearby objects that may impede dir circmlation
   • Verify that the diameter of the blades of your ran is sullicient tor the area of the room in which it is installed
6. The light does not turn on
   • Check the bulb is not blown, otherwise replaces it with a ney one
   • If your fan has LED light included, check the connections are properly tixed according to the instruction manuol.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the ight. This unction allows vou to maintain the same color temperature when the tan light is Turned on again To change the color temperature, turn off the light by pressing the Lamp ON/OFF’ button once and furn it on again by pressing the button again within 2 seconds.  Turn the light off again by pressing Lamp ON/OFF and oiler ‘S seconds turn it on again, it will  keep the last selected temperatur.

REMOTE CONTROL

WINTER/SUMMER MODE
Reverse the direction of rotation of the blades to change to summer mode or winter mode

LAMP ON/OFF / SYNCHRONIZATION
Turns the light and synchronization on or off (see section Control synchronization”).

FAN ON/OFF
Turn the fan on or off.

SPEED REGULATOR
Increases or decreases the turning intensity of the blades.

PROGRAMMING
Sets the hours of fan operation (1, 2 or 4 hours).

BREEZE MODE
Activate the breeze mode that alternates smoothly between soft and fast speeds (from speed 1 to 3) to create a greater sensation of comtort.

To activate the breeze mode, activate the fan using the “ON/OFF button on the fan and then press the ‘Breeze mode button. For cancel breeze mode oress the “Breeze mode”  button again, the fan will return to the rotation speed selected before the breeze mode. You can also press the ON/OFF button of the fan to completely stop the rotation of the blades, when you turn it on again it will not remember the  breeze mode, activating at the previously selectedrotation speed.*The remote control is synchronized from the factory, you only need to re-synchronize it if the synchronization has been lost if you purchased a new one or want to control several fans with a single remote.

BATTERIES
The remote control batteries are not included. The required battery model is 2x AAA. *Remove the batteries from the controller if it not going to be used for a long time.

SPEAKER

1. Turn off bluetooth smartphone
   Verify that the Bluetooth function of the personal device (smartphone) is turned off.

2. Activate bluetooth fan
   Check that the power is on (the fan reacts to any  button on the remote control such as light or air),press and hold the speaker button on the remote control for 2 seconds until you hear the signal (2 short beeps in a row) so that the Bluetooth speaker enters pairing mode.

3. Activate bluetooth smartphone
   Activate the Bluetooth function of the personal device (smartphone) and enter search / pairing mode. You may have to wait up to 30 seconds for the ventilator speaker to appear, depending on the mobile device being used. It may appear with the name MISTRA  orCARMEN

   • ATTENTION: If no device named MISTRA or CARMEN has been found, press and hold the speaker button on the remote control for 2 seconds to turn off the Bluetooth of the ventilator (a ‘click’ will be heard). Subsequently, press and hold the speaker button on the controller for 2 seconds until you hear the signal (2 short beeps in a row) to turn it on again, and repeat step 3.

4. Pair device
   Select the name of the speaker indicated in Step 3 and pair. You will hear a signal indicating a  successful connection

APP DOWNLOAD

1. You will need to download the “Lamp” app to your mobile device (smartphone) from the mobile application distribution platform corresponding to the operating system of your mobile device.

SYNCHRONISATION OF THE “ULAMP” APP

1. Opening the application
   Open the application once it has been installed on the smartohone.

2. Activate Bluetooth and Location
   Activate Bluetooth and Location from the APP or from your mobile phone settings.

3. Turn on the fan light
   Turn on the fan light with the remote control.

4. Open the application
   Open the ULAMP application on your mobile phone.

5. Add device
   On the main screen of the application, press the button with the symbol ‘+*

6. Search and link device With the fan light on and the mobile bluetooth activated, a device with the name will appear on the screen press “Add*Once loaded, press “Finish adding.Once you have the device on your screen, you can edit its name by clicking on the symbol ¿ . Once you have changed the name, press “Confirm” Then click “Save

7. Synchronise device
   Wait for the download of the “Control Panel to complete. When it has uploaded 100%, you will  have your device linked and your controlpanel will appear

BOTONES

1. Configuration

2. RGB light control screen
   Access to the RGB light control screen.

3. White light control screen
   Access to the white light control screen.

4. ON/OFF

5. Colour wheel
   Touch circle where the colour can be adiusted.

6. RGB colours
   Selection of preset RGB colours.

7. Light intensity
   Adjusts the light intensity.

8. Colour
   Access to the light colour control screen.

9. Ambient scenes
   Access to the ambient scenes. The colour and light intensity varies depending on the scene you choose.

10. Timer
    Access to the timer for switching off thelight.

DESYNCHRONISATION
To unsynchronise the device, press the “Settings” button and the “Delete button.

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized, you only need to resynchronize the remote if you have lost synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

A REMOTE CONTROL TO A NEW FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30%

2. Restore the current
   Past 30° re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light  during 3 seconds until you hear the signal and the light flashes Control range: 8-10m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut off the current until all fans stop and wait 30*

2. Restore the current
   Past 30′ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light ” on each fan during 3 seconds until you hear the signal and the light flashes. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize at the same time.

A REMOTE CONTROL TO A FAN
(Example for two fans, applicable to a larger number of fans)

1. **Cut the fan A current***
   Be sure to cut the fan A current (the one we want to remove the synchronization) and wait 30°.

2. **Cut the fan B current**
   Be sure to cut off fan B (the one we want to synchronize) and wait 30

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button “ON/OFF light ” during 3 seconds until you hear the signaland the light flashes to synchronize remote control B with fan

4. **Cut the fan B current**
   Be sure to cut the fan B current and wait 30.

5. Restore the fan A current
   When you restore the fan A and within 10 seconds, press the synchronization button “ON/OFF light ” during 3 seconds until you hear the signaland the light flashes to synchronize remote control A with fan A

6. Repeat the steps
   Repeat steps with each fan you have and want to individualize its remote control.

“To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the fan.

TWO REMOTE CONTROLS TO ONE FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30%.

2. Restore the current
   Past 30* re-establish the current.

3. Synchronize the remote control A
   Within 10 seconds, press the synchronization  button “ON/OFF light ” during 3 secondsuntil you hear the signal and the light flashes. Control range: 8-10m .

4. Cut the current
   Be sure to cut off the current until the fan stop and wait 30*

5. Restore the current
   Past 30° re-establish the current

6. Synchronize the remote control B
   Within 10 seconds, press the synchronization button *ON/OFF light (.)” during 3 seconds until you hear the signal and the light flashes. Control range: 8-10 m

It is not possible to synchronise more than two controllers to one fan.

PARTS OF A FAN

GENERAL GUIDE: PARTS OF A FAN

SCREW GUIDE

INSTALLATION INSTURCTION

WIRING

PARTS DESCRIPTION

CONTACT

• www.arteconfort.com.
• ARTECONFORT HOTEL S.L.
• Ctra. Andalucía, 6
• 45224 Seseña Nuevo
• Toledo, España

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>