DAKE 33-493 Electric Tire Press Instruction Manual

DAKE 33-493 Electric Tire Press

Introduction

WARNING! Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury.

SAFEGUARDING THE POINT OF OPERATION

NSI B11.2 – Hydraulic Power Presses – Safety Requirements for Construction, Care, and Use

It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for a more complete understanding of their responsibilities.

ANSI B11.2 states the following, relative to point of operation safeguarding:

“Normally, only the employer (press user) can determine the requirements of the press productions system components, including the dies and methods for feeding. Therefore, the employer is ultimately responsible to designate and provide the point-of-operation safeguarding system.”

The standard also discusses additional responsibilities of the employer. Some of the key responsibilities are:

• The employer is responsible for the safety, use, and care of the hydraulic power press production system.
• The employer is responsible to consider the sources of hazards for all tasks to be implemented on the hydraulic power press production system.
• The employer is required to eliminate or control identified hazards in the scope of their work activity.
• The employer is responsible for the training of personnel, caring for, inspecting, maintaining, and operating hydraulic press production systems to ensure their competence.
• The employer is responsible to provide and ensure that point-of-operation safeguarding is used, checked, maintained, and where applicable, adjusted on every production operation performed on a press production system.

A complete and current copy of the ANSI B.11.2 standard can be obtained by contacting the following:

American National Standards Institute
1430 Broadway
New York, NY 10018

AMT – The Association For Manufacturing Technology
7901 Westpark Drive
McLean, VA 22102

SPECIFICATIONS

In the space provided record the serial number and model number of the machine. This information is only found on the black and gold Dake tag shown below. If contacting Dake this information must be provided to assist in identifying the specific machine.

SAFETY

This is the safety alert symbol. When you see this symbol on your press be alert to the potential for personal injury.
Employer is responsible to perform a hazard/PPE assessment before work activity.

Follow recommended precautions and safe operating practices.

• Carefully read all safety messages in these instructions and on your press safety signs. Keep safety labels in good condition. Replace missing or damaged safety labels.
• Do not alter this press from its original design.
• Do not make repairs or adjustments to any hydraulic system unless you are competent or working under competent supervision.
• Only use Dake original parts.
• This machine is intended to be operated by one person. This person should be conscious of the press ram movement not only for themselves but also for persons in the immediate area of the machine.
  

SET UP

1. Anchor press to floor using 11/16” holes on the base angles of the press.
2. Fill press with oil. We recommend DTE Mobil 24 or equivalent hydraulic oil.
3. Oil Capacity: 7 Gallons

CAUTION: Strainer or filter should be used to make sure no contaminants get into reservoir.

OPERATION

HOIST

Press is equipped with hoist and hoist handle to raise and lower the upper platen to desired working height.
To change the vertical position of the upper platen sufficient tension must be applied to the hoist cable to permit removal of the table pins, then the upper platen may be moved to desired working position and all the table pins must be reinserted.

Be sure all table pins are on place before applying any pressure. Also make sure there is slack in the hoist cable before pressing. It is advisable to lower the upper platen opposed to running the ram and lower platen to the limit of its stroke.

RAM MOVEMENT

• To raise ram/platen, turn the release valve handle clockwise to close.
• Press “Raise” button to raise ram, ram will stop when button is released.
• After the work is contacted the press will build pressure until maximum tonnage or stroke is reached or the button is released.
• To release pressure and lower ram, turn release valve counterclockwise to open. Platen will return to its starting position.

MAINTENANCE

LUBRICATION

• Keep all working parts of the press well-oiled for easier operation.
• Keep a light film of oil over the entire surface of the ram to prevent rust.

REPLACING HYDRAULIC OIL

Recommended to replace hydraulic oil every 6 months of machine use.
Amount needed may vary dependent on machine use

TROUBLESHOOTING

When performing any maintenance make sure proper lockout procedure is followed.
When disconnecting any parts of this machine be extremely careful that all parts are clean to prevent entrance of dirt in the hydraulic system.

A. Oil leaks around the piston.

1. Oil above the Piston Seal or Leather: If rated stroke of the press is exceeded repeatedly by running the piston past rated stroke, bypass hole in the side of the cylinder run bypass line that connects above the piston leather. Eventually enough oil may accumulate so that when the piston is raised to the top of its stroke, oil is forced out between the piston and piston guide. This can be remedied by disconnecting the bypass tube line from the cylinder, then raising the piston slowly, about 2-1/2” less than it’s rated stroke (rated stroke: 18”) allowing the oil above the piston cap to overflow out the bypass hole into a clean bucket. Replace tube line. Oil may be put back into reservoir by removing the fill plug on the top of the reservoir.
2. Check Valve not Seated: On the first presses made with rapid advance the bypass oil was returned through a check valve at the bottom of the reservoir. This has been changed since so that the oil is returned to the top of the reservoir, above the oil level. Previously, if the check valve failed to seat properly when the press was operated at rapid advance speed oil was forced back through the bypass line causing leakage around the piston. These olstyle rapid advance presses can be improved by relocating the check valve in the inspection cover so that the oil from the bypass line discharges above oil level.

B. Press does not hold pressure.

1. Loose tube Connection: Check all connections and tighten any loose tube nuts.
2. Dirt under Release Valve Ball: Remove release valve stem, packing nut, packing, and ball. Clean out valve seat. Reseat valve ball using a brass rod as a drift and hit with significant force 2-3 times to reset ball. Reassemble valve. If this occurs frequently the oil should be drained from the reservoir and the reservoir should be flushed out. Fill reservoir with clean oil.
3. Worn Leather Cup or Piston Seal: If neither of the previous conditions seem to be the cause of the press not holding pressure the trouble may be that the piston leather or T-ring & backers are worn out or damaged. To inspect remove lower platen and remove cap screws which bolt piston guide to the cylinder flange. Piston and guide may now be lifted out of the cylinder and inspected or replaced if necessary. Be careful not to damage the lip of the leather cup or T-ring as it enters the cylinder.

C. Press does not develop rated tonnage.

1. Dirt under Release Valve Ball: See section above.
2. Worn Leather Cup or Piston Seal: See section above.
3. Relief Valve was tampered: The relief valve has been set at the factory to bypass oil back to the reservoir when the press reaches its rated capacity. If however the press does not develop its rated tonnage and the above two conditions have been checked, the relief valve may need readjusting. To do this first remove the 1/4” pipe plug in the connector block. Now the valve adjustment screw can be reached with a 7/32” hex wrench. To increase the setting, turn the adjustment screw clockwise
   Be careful not to adjust the valve over its rated tonnage or maximum operating pressure of 6000PSI.

D. No ram movement.

1. Release Valve is open: Be sure release valve is firmly closed.
2. Insufficient oil: This is not a likely to be the issue on a tire press but if the press will only make a fraction of its rated stroke and no more, check the oil level in the reservoir. With the ram down the oil should be about 4” from the top of the reservoir.
3. Pump loses its prime: Make sure all pump intake connections are tight.
4. Repaired Improperly: If press has had any maintenance in the past it is possible that a check valve spring or check ball got missed in the repairs.

E. Press is too slow.

1. Wrong oil: Oil that is too heavy will slow the pressing speed. DTE Mobil 24 or equivalent hydraulic oil.

ELECTRICAL DIAGRAM

HYDRAULIC DIAGRAM

PARTS LISTS

MAIN ASSEMBLY

Qty| Part No.| Description
1| 75151| Connector, Cord
1| 63565| Decal, Tire Press
1| 710458| Frame Assembly
1| 300168| Ganged Warning Label
3| 66243| Heater Overload – Voltage Specific
1| 710459| Hydraulic Control Assembly
1| 710444| Hydraulic Pumping Unit
1| 84487| Label, Caution
1| 84395| Label, Danger
1| 76462| Label, Lockout Procedure
1| 76936| Label, Made In U.S.A.
1| 84399| Label, Warning
1| 57794| Legend Plate
1| 35941| Limit Switch Assembly, Micro
1| 46743| Limit Switch Lever, Micro
3| 43643| Lock Washer (1/4″)
1| 75257| Locknut, Conduit, 1/2 In.
1| 44066| Pipe, Reducer Bushing
1| 76868| Pushbutton Unit, AB
3| 43301| Screw (1/4-20 x 1/2)
1| 77353| Starter Enclosure – Voltage Specific 220V
1| 77354| Starter Enclosure – Voltage Specific 440V
1| 79956| Tag, No Oil in Reservoir
6| 43647| Washer, Lock (1/2″)
1| 707070| Workhead
2| 1551P| Base Angle
19′| 45930| Cable (1/4″)
4| 583| Clamp, Cable (1/4″)
1| 36863| Decal, Tire Press
1| 47411P| Frame
1| 61063L| Guide Angle – Left
1| 61063R| Guide angle – Right
2| 1812P| Head Channel
1| 701653| Hoist Crank Assembly
1| 607| Label, Model Number
1| 81003| Name Plate, Dake
2| 43916| Nut, Hex (1/2-13)
8| 43919| Nut, Hex (3/4-10)
8| 43917| Nut, Hex (5/8-11)
6| 77271| Pin, Spring (3/8″ Dia. x 2-1/2″)
6| 7205P| Pin, Table
1| 1798P| Platen, Lower
1| 1813P| Platen, Upper
2| 1563P| Pulley
2| 1809P| Pulley Cable
6| 43978| Ring, Retaining (3/4″ Shaft Size)
6| 302816| Safety Pin
4| 43365| Screw (5/8-11 x 1-3/4)
6| 70277| Screw, Drive (#4 x 5/16″)
2| 43349| Screw, Hex Cap (1/2-13 x 1-1/2)
4| 43373| Screw, Hex Cap (3/4-10 x 2)
4| 43326| Screw, Hex Cap (3/8-16 x 3/4)
8| 43348| Screw, Machine (1/2-13 x 1-1/4)
4| 24569| Screw, Soc Cap (3/4-10 x 3-1/4)
1| 1810P| Shaft, Cable Pulley
2| 1811P| Shaft, Cable Pulley
4| 1819P| Stop Block
1| 700111-S| Table Hoist Sub Assembly
4| 1553P| Table Spacer
4| 1553P| Table Spacer
10| 43647| Washer, Lock (1/2″)
12| 43649| Washer, Lock (3/4″)
4| 43645| Washer, Lock (3/8″)
4| 43648| Washer, Lock (5/8″)
710444 HYDRAULIC PUMPING UNIT

Qty| Part No.| Description
1| 588| Pipe Plug (3/8 NPTF)
2| 1567| Pipe Plug (1/4 NPTF)
1| 1745| Pipe Plug (3/4 NPTF)
4| 2248| Washer, Neoprene
1| 23764| Fitting, Tube, 37 Deg. (Straight Thd Straight O-Ring, SAE 6-8)
1| 29571| Filter Breather
1| 29650| Valve, Relief
1| 36509AP| Pump & Motor Base
4| 43314| Screw, Hex Cap (5/16-18 x 3/4)
4| 43315| Screw (5/16-18 x 1)
4| 43330| Screw, Hex Cap (3/8-16 x 1-1/4)
8| 43644| Washer, Lock (5/16″)
4| 43645| Washer, Lock (3/8″)
4| 43846| Screw (#10-24 x 3/8)
1| 47343P| Reservoir
1| 53721| Pipe, Cross,
2| 58227| Fitting, Pipe, Straight (3/4″ Male Pipe Nipple with Hex)
1| 72052| Fitting, Tube, 37 Deg. (90 Deg. Elbow, 1/2 x 3/4 NPTF)
1| 73458| Fitting, Tube, 37 Deg. (Straight Thd Elbow SAE O-Ring 8-12)
1| 301756| Pump
1| 301757| Adapter, Pump to Motor
1| 301762| Coupling Assembly
1| 301800| Motor
1| 712016| Tube Assembly – Intake Line
1| 712017| Tube Assembly – Pump to Relief Valve
–| 710444| Hydraulic Pumping Unit (Includes all items in table)

707070A Workhead Assembly – New Style

Item| Part No.| Description| Qty
1| 1796P| Piston| 1
2| 52478P| Retainer| 3
3| 31871| Guide, Piston| 1
4| 43647| Washer, Lock (1/2”)| 10
5| 43419| Screw, Soc Cap (1/4-20 x 2)| 4
6| 43359| Screw, Hex Cap (1/2-13 x 4-1/2)| 4
7| 1793P| Cylinder| 1
8| 43817| Screw, Fl. Hd. Slot Mach. (#10-24 x 1/2)| 3
9| 1871| Oil Seal,| 1
10| 31400| Wear Ring| 2
11| 43358| Screw, Hex Cap (1/2-13 x 4)| 6
12| 589| Pipe Plug (1/8 NPTF)| 2
13| 87611P| Piston Cap| 1
14| 43916| Hex Nut, (1/2-13)| 10
15| 31399| Wear Ring| 1
16| 37052| 1-T-ring, 2-backers| 1
–| 707070A| Workhead Assembly (Includes Items: 1-3, 5-16)| –
–| 703922| Workhead Repair Kit (For 707070 & 707070A) Includes Items : 9, 10, 15 & 16.| –

707070 Workhead Assembly – Old Style

Item| Part No.| Description| Qty
1| 1796P| Piston| 1
2| 52478P| Retainer| 3
3| 31871| Guide, Piston| 1
4| 43647| Washer, Lock (1/2”)| 10
5| 43916| Screw, Soc Cap (1/4-20 x 2)| 10
6| 43359| Screw, Hex Cap (1/2-13 x 4-1/2)| 4
7| 1793P| Cylinder| 1
8| 43817| Screw, Fl. Hd. Slot Mach. (#10-24 x 1/2)| 3
9| 1871| Oil Seal,| 1
10| 31400| Wear Ring| 2
11| 43358| Screw, Hex Cap (1/2-13 x 4)| 6
12| 589| Pipe Plug (1/8 NPTF)| 2
13| 30425P| Piston Cap| 1
14| 43417| Screw, Soc Cap (1/4-20 x 1-1/2)| 4
15| 31399| Wear Ring| 1
16| 43332| Screw (3/8-16 x 1-3/4)| 8
17| 1538| Piston Leather| 1
18| 43645| Washer, Lock (3/8”)| 8
19| 1536| Ring, Supporting| 1
N/A| 1567| Pipe Plug (1/4 NPTF)| 2
–| 707070| Workhead Assembly (Includes all items above)| –
–| 703922| Workhead Repair Kit (For 707070 & 707070A) Includes Items : 9, 10, 15 & 17.| –

710459 HYDRUALIC CONTROL ASSEMBLY

710557 RELEASE VALVE ASSEMBLY

700111-S TABLE HOIST

ORDERING INFORMATION

Please contact factory for current prices.

Parts are available for direct purchase from Dake or through a distributor. When placing a parts order, you will need to provide the part number, name of part, and model number. All parts shipped F.O.B. Factory in Grand Haven, MI.

CUSTOMER SUPPORT

Dake Corporation
1809 Industrial Park Dr
Grand Haven, MI 49417
www.dakecorp.com

References

• Dake Corp | Metalworking Machine Tools
• Metalworking Machine Tools | Dake Corp

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>