DAKE 985017-1 Bandsaw Instructions
- October 30, 2023
- DAKE
Table of Contents
985017-1 Bandsaw
Instructions
EXPLODED VIEW & PARTS LIST
| Item | Part Name | Part Number | Qty |
|---|---|---|---|
| 1 | Front Frame | 10002-01 | 1 |
| 2 | Rear Frame | 10003-01 | 1 |
| 3 | Bed | 10001-00 | 1 |
| 4 | Pivot Bar | 10066-00 | 1 |
| 5 | Shaft Locking Collar | 13010-08 | 2 |
| 6 | Right Leg | 10004-02 | 1 |
| 7 | Left Leg | 10005-02 | 1 |
| 8 | Balance Spring – includes carriage bolt and nut | 10070-00 | 1 |
| 9 | Spring Perch | 10100-01 | 1 |
| 10 | Outboard Bearing Casting – (3/8” bolt, lock washer, & nut) | 10101-00 | 1 |
| 11 | Stock Stop Assembly | 5527-00 | 1 |
| 11A | Holder Casting | 5027-00 | 1 |
| 11B | Rod | 5213-00 | 1 |
| 11C | Spring | 5028-00 | 1 |
| 11D | Handle (S/N 10962) | 5200-00 | 1 |
| 12 | Stock Stop Mounting Bar | 5027-01 | 1 |
| 13 | Tip-off Block | 10006-01 | 1 |
| 14 | Coolant Drawer Pan | 10269-00A | 1 |
| 15 | Left Hand Blade Guard | 300405A | 1 |
| 16 | Right Hand Blade Guard | 300404A | 1 |
| 18 | Left Leg Pan | 10268-07A | 1 |
| 19 | Right Leg Pan | 10268-05A | 1 |
| 20 | Frame Handle | 10093-00 | 1 |
| 21 | Brush Holder Guard | 10229-00 | 1 |
| 22 | Name Plate | 72295 | 1 |
| 23 | Submersible Coolant Pump – Electric 110 Volt | 71541 | 1 |
PARTS NOT ILLUSTRATED
| Description | Part No. | Qty |
|---|---|---|
| Motor, 110/230 Volt, 60 Hz Single-Phase, 1 H.P. | 10079-07 | 1 |
| Motor Pulley – 5/8” Bore (1 Used on Old Style) | 10042-10 | 2 |
| Drive Belt | 10077-10 | 1 |
| Pulley Guard | 10223-10A | 1 |
| Motor Mounting Bracket | 5107-00 | 1 |
| Stationary Motor Bracket | 5106-02 | 1 |
| Motor Mounting Pin | 5106-03 | 1 |
| Frame Covers (Left and Right) | 300403A | 2 |
| Knob for Frame Covers | 300804 | 4 |
| Rear Frame Blade Guard | 10230-10A | 1 |
| Drive Wheel Drip Pan | 10271-00A | 1 |
| Wheel Pan Strap | 10287-00 | 1 |
| Wheel Pan Bar | 10286-00 | 1 |
| Thumb Screw – Drive Wheel Drip Pan (S/N 10962) | 70295 | 2 |
| Spring Bracket Top | 10209-01 | 1 |
| Lower Left Front Cover | 10126-13A | 1 |
| Frame Rest (S/N 10962) | 10091-10 | 1 |
| Drive Wheel Cover | 300407A | 1 |
| Idle Wheel Cover | 300408A | 1 |
| Drive & Idle Wheel Spoke Guards (Not used on current model) | 300409A | – |
| Wire Ties | 300246 | 8 |
OTHER VOLTAGE MODELS
Bandsaw Sub-Assembly same for 985017-1, 985017-2, 98518-2, & 985018-4.
Parts that differ from 110V Model below:
985017-2 220V Single Phase Model
| Part Name | Part Number | Qty |
|---|---|---|
| Motor, 110/230 Volt, 60 Hz Single-Phase, 1 H.P. | 10079-07 | 1 |
| Wire Nut | 300171 | 4 |
| 16-14 Wire #10 Stud Non-Insulated Ring Terminal | 300245 | 4 |
| Wire Tie | 300246 | 8 |
| Quick Connect Terminal | 300524 | 3 |
| Electrical Control Box Assembly | 716676 | 1 |
| Flexible Conduit Assembly | 716679 | 1 |
| Connector, Cord | 75151 | 1 |
| Locknut, Conduit, 1/2 In. | 75257 | 1 |
| Roll Pin (1/4” x 2-1/2”) | 75516 | 4 |
985018-2 220V 3-Phase Model
| Part Name | Part Number | Qty |
|---|---|---|
| Motor, 208/230/460V, 50/60 Hz. 3-Phase | 10079-05 | 1 |
| Wire Nut | 300171 | 5 |
| 16-14 Wire #10 Stud Non-Insulated Ring Terminal | 300245 | 4 |
| Wire Tie | 300246 | 3 |
| Quick Connect Terminal | 300524 | 3 |
| Electrical Control Box Assembly | 716677 | 1 |
| Flexible Conduit Assembly | 716680 | 1 |
| Connector, Cord | 75151 | 2 |
| Locknut, Conduit, 1/2 In. | 75257 | 2 |
| Roll Pin (1/4” x 2-1/2”) | 75516 | 4 |
985018-4 440V 3-Phase Model
| Part Name | Part Number | Qty |
|---|---|---|
| Motor, 208/230/460V, 50/60 Hz. 3-Phase | 10079-05 | 1 |
| Wire Nut | 300171 | 5 |
| 16-14 Wire #10 Stud Non-Insulated Ring Terminal | 300245 | 4 |
| Wire Tie | 300246 | 3 |
| Quick Connect Terminal | 300524 | 3 |
| Electrical Control Box Assembly | 716678 | 1 |
| Flexible Conduit Assembly | 716680 | 1 |
| Connector, Cord | 75151 | 2 |
| Locknut, Conduit, 1/2 In. | 75257 | 2 |
| Roll Pin (1/4” x 2-1/2”) | 75516 | 4 |
WHEEL ASSEMBLIES
| Item | Description | Part No. | Qty |
|---|---|---|---|
| 1 | Idle Wheel/Frame Mounting Bracket (Outboard) | 10064-09 | 1 |
| 2 | Idle Wheel Assembly | 10510-04A | 1 |
| 2 | Idle Wheel Assembly (Old Style) | 10510-04 | 0 |
| 2A | Idle Wheel Only | 13035-01A | 1 |
| 2A | Idle Wheel Only (Old Style) | 13035-01 | 0 |
| 2B | Wheel Axle | 10062-00 | 1 |
| 2C&D | Bearing – Sealed (2 per wheel assembly) | 81583 | 1 |
| – | Snap Ring for Bearing #81582 | 81585 | 2 |
| 2C | Bearing Cup (Old Style) | 10134-01 | 0 |
| 2D | Bearing Cone (Old Style) | 10134-02 | 0 |
| 2E | Dust Collar (Old Style) | 10135-00 | 0 |
| 2F | Snap Ring (Old Style) | 10136-00 | 0 |
| 2G | Grease Fitting (Old Style) | 5143-00 | 0 |
| 2H | Hex Jam Nut 1”-14 N.F. | 14123 | 1 |
| 2J | Locknut 1”-14 N.F. | 70296 | 1 |
| 3 & 4 | Slide & Rocker Block Assembly | 5011-01 | 1 |
| 5 | Idle Wheel & Frame Mounting Bracket (Inboard) | 86526 | 1 |
| 6 & 7 | Tension Screw Assembly | 10125-01 | 1 |
| 8 | Wheel Guideway Angle – Top | 10210-00 | 1 |
| 10 | Wheel Guideway Angle – Bottom | 10067-00 | 1 |
| 12 | Drive Wheel & Frame Mounting Bracket (Inboard) | 86525 | 1 |
| 13 | Gear Box Mounting Plate | 10063-00 | 1 |
| 14 | Drive Wheel & Frame Mounting Bracket (Outboard) | 10064-06 | 1 |
| 15 | Driven Pulley – 3/4” Bore (Key – Part No. 71061) | 10043-10 | 1 |
| 16 | Drive Wheel Assembly | 10510-03A | 1 |
| 16 | Drive Wheel Assembly (Old Style) | 10510-03 | 0 |
| 16A | Drive Wheel only | 10010-03A | 1 |
| 16A | Drive Wheel only (Old Style) | 10010-03 | 0 |
| 16B | Ring Gear | 10052-00 | 1 |
| 16C | Wheel Axle | 10062-00P | 1 |
| 16C | Wheel Axle (Old Style) | 10062-00 | 0 |
| 16D&E | Bearing – Sealed (2 per wheel assembly) | 81583 | 2 |
| – | Snap Ring for Bearing #81582 | 81585 | 2 |
| 16D | Bearing Cup (Old Style) | 10134-01 | 0 |
| 16E | Bearing Cone (Old Style) | 10134-02 | 0 |
| 16F | Dust Collar (Old Style) | 10135-00 | 0 |
| 16G | Snap Ring (Old Style) | 10136-00 | 0 |
| 16H | Grease Fitting (Old Style) | 5143-00 | 0 |
| 16J | Hex Jam Nut, 1”-14 N.F. | 14123 | 1 |
| 16K | Locknut 1”-14 N.F. | 70296 | 1 |
| 16M | Soc Cap Screw Flathead 1/4”-20 x 1-1/4” | 78489 | 6 |
| Not Shown | Idle Wheel Mounting Bolts (3/4”-16 x 1-1/4”) | 70346 | 2 |
GEARBOX ASSEMBLY
| Item | Description | Part No. | Qty |
|---|---|---|---|
| – | Gear Case Complete | 10544-00A | 1 |
| – | Gear Case Complete (Old Style) | 10544-00 | 0 |
| 1 | Bearing Cap | 5047-00 | 2 |
| 2 | Cap Gasket | 5138-00 | 2 |
| 3 | Bearing | 5073-00 | 1 |
| 4 | Gear Case | 5044-00 | 1 |
| 5 | Dowel Pin | 3922 | 2 |
| 6 | Bearing | 5072-00 | 3 |
| 7 | Worm Gear Shaft | 10049-00 | 1 |
| 8 & 15 | Worm – Steel Worm & Bronze Gear Assembly | 10050-00 | 1 |
| 9 | Cover Gasket | 13080-01 | 1 |
| 10 | Gear Case Cover | 5045-00 | 1 |
| 11 | Breather Vent | 7368 | 1 |
| 12 | Oil Seal | 5137-22 | 2 |
| 13 | Snap Ring | 5136-00 | 2 |
| 14 | Worm Shaft | 5048-00AP | 1 |
| 14 | Worm Shaft (Old Style) | 5048-00 | 0 |
| 15A | Key (3/16” x 3/16” x 3/4”) | 71061 | 1 |
| 16 | Spur Gear (Set Screw – Part No. 43558) | 10053-00 | 1 |
| 17 | Key (3/16” x 3/16” x 1/2″) | 10047-01 | 1 |
| Key (3/16 x 3/16” x 1”) | 47364 | ||
| – | Woodruff Key (S/N 10962) | 26189 | 2 |
| – | Bearing & Seal Kit (Includes Items 2, 3, 6, 9, 12, 13) | 714706 | – |
HYDRAULIC ASSEMBLY
| Item | Description | Part No. | Qty |
|---|---|---|---|
| – | Hydraulic Assembly (Includes Cylinder & Control Valve Assembly) | 10530-10 |
1
–| Cylinder Assembly Only| 10530-09| 1
1| Cylinder Base| 10031-00| 1
2| Fiber Seal| 10203-03| 2
3| Tie Rod| 10205-02| 3
4| Spring| 5129-00| 1
4A| Spring – R Style, included in repair kit.| 5116-00| –
5| Valve Ball 3/8”| 17817| 1
6| Piston Rod| 10204-02| 1
7| Head Stop Spring| 10033-00| 1
8| Cylinder Head| 5030-10| 1
9| Head Seal (O-Ring) (S/N 10962)| 10115-02| 1
9A| Older Models Garlock Shaft Seal (1/2” ID, 7/8” OD, 1/8” Thick) (S/N
10962)| 10115-03| 1
9B| Older Models Garlock Shaft Seal (1/2” ID, .801” OD, 1/8” Thick) (S/N
10962)| 13080-03| 1
10| Yoke| 10013-00| 1
11| Hex Nut #10-24| 43905| 3
12| Tube Elbow (Includes furrow and nut)| 71357| 2
13| Cylinder Body| 10203-02| 1
14| Piston| 5119-00| 1
15| Piston Nut| 5120-00| 1
16| Leather Cup| 5130-00| 1
–| Control Valve Assembly| 10530-08|
23| Hydraulic Needle Valve (Incudes Knob) (New Style: Serial No. > 1403165)|
303690| 1
23B| Hydraulic Needed Valve (Old Style: Serial No. < 1403165)| 5131-00| –
24| Tube Fitting (For New Style Valve)| 303691| 2
24| Tube Fitting (For Old Style Valve)| 44143| 0
26| Face Plate| 10030-00| 1
27| Knob (For Old Style Valve)| 13018-14| 1
28| Drive Screws| 70277| 4
29| Tubing 5/16”| 40515-00| 8 ft.
30| Tubing 5/16”| 40515-00| 8 ft.
–| Hydraulic Filler Cap. Items 18-21 not needed if saw is equipped with filler
cap.| 5032-00| 1
–| Hydraulic Cylinder Repair Kit (Items 2, 4, 4A, 5, 9, 9A, 9B & 16)| 714717|
–
–| Rod & Piston Assembly (Items 4, 5, 6, 14, 15, & 16)| 10530-01| –
GUIDE ARM ASSEMBLY
| Item | Description | Part No. | Qty |
|---|---|---|---|
| – | 1” Guide Arm Assembly Complete – Stationary – Right | 10519-11A | 1 |
| – | 1” Guide Arm Assembly Complete W/ Coolant Nozzle – Left | 10519-10AW | 1 |
| 1 | Guide Arm (LH/RH) | 10019-10 | 2 |
| 2 | Guide Holder | 10020-10 | 2 |
| 3 | Guide Arm Handle | 10084-01 | 1 |
| 4 | Side Guide Bearing | 10025-01 | 2 |
| 5 | Upper Guide Bearing | 5026-00 | 2 |
| 6 | Upper Guide Bushing | 5023-01 | 2 |
| 7A | Side Guide Bushing | 5075-00 | 2 |
| 7 | Inside Concentric Axle (Not on current model) | 10022-02 | 2 |
| 8 | Outside Eccentric Axle Only. Nut #42326, Washer #43644 | 10022-10 | 2 |
| 9 | Brush Holder | 5122-00 | 1 |
| 10 | Blade Brush Kit – 6 Pairs | 5133 | 1 |
| 11 | Coolant Hose Assembly (Includes Nozzle, Connector, & Flex hose) | 715342 | 1 |
| 12 | Tube Fitting, Poly-Tite | 34528 | 1 |
| 12B | Nozzle Mounting Bracket | 82668 | 1 |
| 13 | Tubing 3/8” | 67762 | 8 ft. |
| 14 | Guide Arm (T-Slot) Bolt | 10512-10 | 2 |
| 15 | Spacer Washer (JH Model Only, not on current models) | 70462 | 8 |
| – | Washer for Guide Arm | 43634 | 2 |
| – | Hex Nut for Stationary Guide Arm | 43916 | 1 |
| Guide Holder Assembly (Includes 2, 4, 5, 6, 7A, 8 & Fasteners) | 10520-10 | ||
| Guide Bearing Kit (Includes 4, 5, 6, & 7A) | 715104 | ||
| Blade, J-Saw, 3/4” x 137” x .035, 5/8” VP – Bi-Metal | 75958 | ||
| Blade, JH-Saw, 1” x 137” x .035, 5/8” VP – Bi-Metal | 75957 | ||
| Guide Arm Assembly Complete LH & RH 1” (Old Style) | 10519-10 |
VISE ASSEMBLY
| Item | Description | Part No. | Qty |
|---|---|---|---|
| 1 | Hold Down Block (S/N 10962) | 10007-00 | 1 |
| 2 | Vise Lift | 10099-00 | 1 |
| 3 | Handle 1/4”-20 x 2” | 5200-00 | 1 |
| 4 | Movable Vise Jaw (Bolt – Part No. 43383) | 10008-00 | 1 |
| 5 | Stationary Vise Jaw (Bolt – Part No. 43348) | 10009-00 | 1 |
| 7 | Lift Pin | 10116-00 | 1 |
| 8 | Vise Nut Plate (Self Tapping Screw (10-24) – Part No. 43882) | 10201-00 | 2 |
| 9 | Vise Nut | 10016-00 | 1 |
| 10 | Vise Screw | 10015-10 | 1 |
| 11 | Handwheel | 10014-00 | 1 |
| 12 | Stop Collar | 70464 | 1 |
ORDERING INFORMATION
Please contact factory for current prices.
Parts are available for direct purchase from DAKE or through a distributor.
When placing a parts order, you will need to provide the part number, name of
part, and model number. All parts shipped F.O.B. Factory in Grand Haven, MI.
Dake Corporation
1809 Industrial Park Dr
Grand Haven, MI 49417
www.dakecorp.com
985017/985018
REV032023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>