SUNELL IPR81xxBYxx Bullet Network Camera User Guide

IPR81xxBYxx Bullet Network Camera
User Guide Bullet Network Camera
Quick Setup Guide
NO:101-300-0555-03
Issue:1.3

Precautions

Fully understand this document before using this device, and strictly observe rules in this document when using this device. If you install this device in public places, provide the tip “You have entered the area of electronic surveillance” in an eye-catching place. Failure to correctly use electrical products may cause fire and severe injuries.

WARNING| It alerts you to moderate dangers which, if not avoided, may cause minor or moderate injuries.
---|---
CAUTION| It alerts you to risks. Neglect of these risks may cause device damage, data loss, device performance deterioration, or unpredictable
results.
NOTE| It provides additional information.

WARNING

• Strictly observe installation requirements when installing the device. The manufacturer shall not be held responsible for device damage caused by users’ non-conformance to these requirements.
• Strictly conform to local electrical safety standards and use power adapters that are marked with the LPS standard when installing and using this device. Otherwise, this device may be damaged.
• Use accessories delivered with this device. The voltage must meet input voltage requirements for this device.
• If this device is installed in places with unsteady voltage, ground this device to discharge high energy such as electrical surges in order to prevent the power supply from burning out.
• When this device is in use, ensure that no water or any liquid flows into the device. If water or liquid unexpectedly flows into the device, immediately power off the device and disconnect all cables (such as power cables and network cables) from this device.
• Do not focus strong light (such as lighted bulbs or sunlight) on this device. Otherwise, the service life of the image sensor may be shortened.
• If this device is installed in places where thunder and lightning frequently occur, ground the device nearby to discharge high energy such as thunder strikes in order to prevent device damage.

CAUTION

• Avoid heavy loads, intensive shakes, and soaking to prevent damages during transportation and storage. The warranty does not cover any device damage that is caused during secondary packaging and transportation after the original packaging is taken apart.
• Protect this device from fall-down and intensive strikes, keep the device away from magnetic field interference, and do not install the device in places with shaking surfaces or under shocks.
• Clean the device with a soft dry cloth. For stubborn dirt, dip the cloth into slight neutral cleanser, gently wipe the dirt with the cloth, and then dry the device.
• Do not jam the ventilation opening. Follow the installation instructions provided in this document when installing the device.
• Keep the device away from heat sources such as radiators, electric heaters, or other heat equipment.
• Keep the device away from moist, dusty, extremely hot or cold places, or places with strong electric radiation.
• If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affect monitoring.
• Remove the power plug if the device is idle for a long time.
• Before unpacking, check whether the fragile sticker is damaged. If the fragile sticker is damaged, contact customer services or sales personnel. The manufacturer shall not be held responsible for any artificial damage of the fragile sticker.

Special Announcement

• All complete products sold by the manufacturer are delivered along with nameplates, quick setup guide and accessories after strict inspection. The manufacturer shall not be held responsible for counterfeit products.
• The manufacturer will update this manual according to product function enhancement or changes and regularly update the software and hardware described in this manual. Update information will be added to new versions of this manual without prior notice.
• This manual may contain misprints, technology information that is not accurate enough, or product function and operation description that is slightly inconsistent with the actual product, the final interpretation of company is as a standard.
• This manual is only for reference and does not ensure that the information is totally consistent with the actual product. For consistency, see the actual product.

NOTE
For more information, please refer to website.

Open Package Examination

Open the package, check the appearance of product for no obvious damage, and confirm the item list for table 1-1 is consistent.
Table 1-1 Packing list

Device Structure

2.1 Device Ports
NOTE
Different devices may have different ports and multi-head cables; Please refer to the actual product.
Figure2-1 Multi-head cable 1
Table 2-1 Multi-head cable 1 description

light is on. the network connection is normal: The yellow light flashes when the data is transmitted. Some models maybe not have the lights: Please refer to the actual product.| Support PoE supply.
2| Audio output| Connect to an external audio device such as a speaker.| Applied for camera with audio
function
3| Audio input port| Receive an analog audio signal from devices such as a sound pickup device.
4| Reset button| Long press the reset button for 5 seconds to restore the original settings.|
5| Power supply (DC 12V)| Connect to a 12V direct current (DC) power supply.|
6| G| Alarm output COM| Applied for alarm
function
OUT| Alarm output terminal
G| Alarm input COM
IN| Alarm input terminal

Figure2-2 Multi-head cable 2 Type 1
Orange: Alarm COM0
Yellow: Alarm IN0
Grey: Alarm OUT1
Purple: Alarm COM
Green: RS485+
Blue: RS485-
Type 2
Orange: Alarm COM0
Yellow: Alarm IN0
Grey: Alarm OUT1
Purple: Alarm COM1
Table 2-2 Multi-head cable 2 description

light is on, the network connection is normal; The yellow light flashes when the data is transmitted.| Support PoE supply
2| Audio input port| Receive an analog audio signal from devices such as a sound pickup device.| Applied for audio function
3| Audio output port| Connect to an external audio device such as a speaker.
4| Power supply (DC 12V)| Connect to a 12V direct current (DC) power supply or 24V alternating current (AC) power supply.|
5| Alarm| Applied for alarm function. It may have two types, please refer to the actual product.|

Figure2-3 Multi-head cable 3 Table 2-3 Multi- head cable 3 description

light is on, the network connection is normal; The yellow light flashes when the data is transmitted. Some models maybe not have the lights; Please refer to the actual product.| Support PoE supply.
2| Power supply (DC 12V)| Connect to a 12V direct current (DC) power supply.|
3| Reset button| Long press the reset button for 5s to restore the original settings.|

2.2 Camera Dimensions
NOTE
Different devices may have different dimensions; Please refer to the actual product.
Figure 2-4 Dimensions （Unit: mm）

Device Installation

The Bullet Network Camera can be installed on the ceiling or wall. You can select an installation mode based on site requirements. If the camera is installed on a concrete wall, install the expansion bolts before installing the bracket. If the camera is installed on a wooden wall, use self-tapping screws to install the bracket directly.
Installation Steps:
Step 1 Stick the Installation location sticker on the ceiling or wall, drill three holes based on the marks on the sticker. Drive the plastic anchors into the holes.
Step 2 Connect the multi-connector cable.
NOTE
you can route cables from the top or from aside. If you use the top routing method, drill a hole in the surface first. If you use the side routing method. When you route cables from the side, please route the multi-head cable out from the side gap at the bottom of the camera.
Step 3 Install the camera on the ceiling or wall and fix the screws as shown in figure 3-1.
Figure 3-1 Installing cameraStep 4 Loosen the fixing screw and locking ring to adjust the position so that the camera faces the monitored area, then tighten the locking ring and the fixing screw, as shown in figure 3-2 .
Figure 3-2 Adjusting the monitoring direction Figure 3-3 Installing SD card

Quick Configuration(e.g IE)

4.1 Login
Step 1 Open the Internet Explorer, enter the IP address of IP camera (the default value: 192.168.0.120) in the address box, and press Enter. The login page is displayed as shown in figure 4-1 .
Step 2 Input the user name and password.
**** NOTE

• The default user name and password both are admin. Modify the password when user logs into the system for the first time to ensure system security.
• It is advised to restart the device three minutes later after modifying password.
• User can change the system display language on the login page.

Figure 4-1 LoginStep3 Click Login, the main page is displayed.
4.2 Modify IP address
Choose Configuration > Device > Local Network, the Local Network page is displayed.
Input the IP address in the IP Address box and click Apply as shown in figure 4-2.
After the IP address is set successfully, please use the new IP address to login the Web interface.
Figure 4-2 Local Network 4.3 Browsing Video
To ensure the real-time video can be played properly, you must perform the following operation when you login the web for the first time:
Step 1 The Internet Explorer. Choose Tools > Internet options > Security > Trusted sites > Sites, in the display dialog box, click Add, as shown in figure 4-3.
Step 2 In the Internet Explorer, choose Tool > Internet Options > Security > Customer level, and set Download unsigned ActiveX control and initialize and script ActiveX controls not marked as safe for scripting under ActiveX controls and plug-ins to enable, as shown in figure 4-4.
Figure 4-3 Adding a trusted siteFigure 4-4 Configuring ActiveX control and plug-insStep 3 Download and install the player control as prompted.
NOTE
If the repair tips displayed when installing the control, please ignore the prompt, and continue the installation, close the Web page during installing. Then login the page again.
To browse a real-time video, login the device and click Live Video. The Live Video page is displayed, as shown in figure 4-5.
Figure 4-5 Live Video

Documents / Resources

| SUNELL IPR81xxBYxx Bullet Network Camera [pdf] User Guide
IPR81xxBYxx Bullet Network Camera, IPR81xxBYxx, Bullet Network Camera, Network Camera, Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>