Freedom Breeder 1040 Reptile Rack Instruction Manual
- June 13, 2024
- Freedom Breeder
Table of Contents
Freedom Breeder 1040 Reptile Rack Instruction Manual
This rack is made of 304 Stainless Steel, no rust ever!
With the exact same dimension as our staple Reptile 1030 rack, we designed the
Reptile 1040 rack with one thing in mind: to add 10 additional tubs to allow
more animals to be kept in the same amount of space. Great for multiple
species of reptiles, we actually house adult female ball pythons up to 3000g
or big breeder males in this rack. With the narrower tub design the animals
seem to express a greater sense of security in the FB40 tub.
Caution
Channels and backstops have sharp edges, take precautions.
PART | DESCRIPTION | QTY |
---|---|---|
1 | Reptile 1040 Stainless Steel Levels | 10 |
2 | 5” Heat Panels | 10 |
3 | FB40 Tubs | 40 |
4 | Base Frame | 1 |
5 | 4” Heavy Duty Casters (Nuts and Bolts Included) | 4 |
Any extra items purchased can be found on your invoice.
Packing list may vary depending on your order.
Requirements
-
1/2” Socket
-
Ratchet
-
Cutter
-
Gloves
-
Two persons *Recommended
STEP 1. Unwrapping
The Reptile 1040 is packed in a cardboard carton and plastic wrap for protection during shipment. Carefully unpack the items and remove the pallet. Notice that the Reptile 1040 is almost assembled.
Note: If you detect any issue or damage please contact us before you accept the shipment.
Count all parts to make sure nothing is missing.
See Packing list for Descriptions and Quantities.
STEP 3. Casters
Notice that the rack may or may not had the casters installed. In case they
have been installed, you just need to turn upside down the frame with the
casters to the correct position.
In case the casters are not installed:
- Find the casters, nuts, and bolts.
- Insert the bolts into the holes in the lower frame.
- Using the ratchet and the 1/2″ socket, tighten the caster with the bolts on each corner of the frame until the bolts are flush to the tubing of the frame.
Note: Make sure to put all the nuts and bolts included (3 per caster) and not overtighten the nuts.
STEP 4. Stacking the levels
Stacked the levels over the base frame with the casters installed. You don’t
have to use tools on this step.
STEP 5. Trays
Insert the trays thru the channels on each level.
STEP 6. Heating system
For the Heating system, place the heating panels over the velcro on each level, and connect the panel system to a source power.
Once all the heating panels are placed and plugged into the power strip, you
will then plug your power strip into your thermostat or your FB-120 x2 and
then plug it into the wall outlet.
If you purchased a power strip from us, you can either simply zip-tie each end
to the side of the rack frame, or zip-screw each end to the rack frame.
Visit our Website, Instagram and Facebook page
ATTENTION CUSTOMERS:
Please inform the appropriate personnel to always INSPECT YOUR SHIPMENT for
damage PRIOR to signing the delivery receipt. If there is obvious damage, do
not accept the shipment without
NOTING IN DETAIL and taking pictures of the damage on ALL copies of the
carrier’s delivery receipt. Please have the freight driver SIGN ALL COPIES to
acknowledge your damage notation.
*Any comments or suggestions on this Instructions Manual please send us an
email to manuel@freedombreeder.com
www.FreedomBreeder.com 209.664.9600 EXT.
201/202/203
Freedom Breeder · 2306 S. Daubenberger Rd. Turlock, CA 95380 USA