CAME BXV04AGS Sliding Gate Motor Instruction Manual
- June 13, 2024
- CAME
Table of Contents
CAME BXV04AGS Sliding Gate Motor Instruction Manual
GENERAL PRECAUTIONS FOR INSTALLERS
Important safety instructions.
Please follow all of these instructions. Improper installation may cause
serious bodily harm.
Before continuing, please also read the general precautions for users.
Only use this product for its intended purpose. Any other use is hazardous.
- The manufacturer cannot be held liable for any damage caused by improper, unreasonable or erroneous use.
- This product is defined by the Machinery Directive (2006/42/EC) as partly completed machinery.
- Partly completed machinery means an assembly which is almost machinery but which cannot in itself perform a specific application.
- Partly completed machinery is only intended to be incorporated into or assembled with other machinery or other partly completed machinery or equipment thereby forming machinery to which the Machinery Directive (2006/42/EC) applies.
- The final installation must comply with the Machinery Directive (2006/42/EC) and the European reference standards in force.
- The manufacturer declines any liability for using non-original products, which would also void the warranty.
- All operations indicated in this manual must be carried out exclusively by skilled and qualified personnel and in full compliance with the regulations in force.
- The device must be installed, wired, connected and tested according to good professional practice, in compliance with the standards and laws in force.
- Make sure the mains power supply is disconnected during all installation procedures.
- Check that the temperature ranges given are suitable for the installation site.
- Do not install on slopes i.e. any surfaces that are not perfectly level.
- Do not install the operator on surfaces that could yield and bend. If necessary, add suitable reinforcements to the anchoring points.
- Make sure that no direct jets of water can wet the product at the installation site (sprinklers, water cleaners, etc.).
- Make sure you have set up a suitable dual-pole cut-off device along the power supply that is compliant with the installation rules. It should completely cut off the power supply according to category III surcharge conditions.
- Demarcate the entire site properly to prevent unauthorised personnel from entering, especially minors.
- In case of manual handling, have one person for every 20 kg that needs hoisting; for non-manual handling, use proper hoisting equipment in safe conditions
- Use suitable protection to prevent any mechanical hazards due to persons loitering within the operating range of the operator.
- The electrical cables must pass through special pipes, ducts and cable glands in order to guarantee adequate protection against mechanical damage.
- The electrical cables must not touch any parts that may overheat during use (such as the motor and transformer).
- Before installation, check that the guided part is in good mechanical condition, and that it opens and closes correctly.
- The product cannot be used to automate any guided part that includes a pedestrian gate, unless it can only be enabled when the pedestrian gate is secured.
- Make sure that nobody can become trapped between the guided and fixed parts, when the guided part is set in motion.
- Use additional protection to prevent your fingers from being crushed between the pinion and rack.
- All fixed controls must be clearly visible after installation, in a position that allows the guided part to be directly visible, but far away from moving parts. In the case of a hold-to-run control, this must be installed at a minimum height of 1.5 m from the ground and must not be accessible to the public.
- Where operated with a hold-to-run control, install a STOP button to disconnect the main power supply to the operator, to block movement of the guided part.
- If not already present, apply a permanent tag that describes how to use the manual release mechanism close to it.
- Make sure that the operator has been properly adjusted and that the safety and protection devices and the manual release are working properly.
- Before handing over to the final user, check that the system complies with the harmonised standards and the essential requirements of the Machinery Directive (2006/42/EC).
- Any residual risks must be indicated clearly with proper signage affixed in visible areas, and explained to end users.
- Put the machine’s ID plate in a visible place when the installation is complete.
- If the power supply cable is damaged, it must be immediately replaced by the manufacturer or by an authorised technical assistance centre, or in any case, by qualified staff, to prevent any risk.
- Keep this manual inside the technical folder along with the manuals of all the other devices used for your automation system.
- Make sure to hand over to the end user all the operating manuals of the products that make up the final machinery.
- The product, in its original packaging supplied by the manufacturer, must only be transported in a closed environment (railway carriage, containers,closed vehicles).
- If the product malfunctions, stop using it and contact customer services at serviceinternational@came. com or via the telephone number on the website.
The manufacture date is provided in the production batch printed on the product label. If necessary, contact us at
https://www.came.com/global/en/contact-us.
The general conditions of sale are given in the official CAME price lists
Main points of danger for people
No transiting while the barrier is moving.
Risk of entrapment.
Risk of trapping hands.
Risk of trapping feet.
DISMANTLING AND DISPOSAL
CAME S.p.A. employs an Environmental Management System at its premises. This
system is certified and compliant with the UNI EN ISO 14001 standard to ensure
that the environment is respected and safeguarded. Please continue
safeguarding the environment. At CAME we consider it one of the fundamentals
of our operating and market strategies. Simply follow these brief disposal
guidelines:
DISPOSING OF THE PACKAGING
The packaging materials (cardboard, plastic, etc.) can be disposed of easily
as solid urban waste, separated for recycling. Before dismantling and
disposing of the product, please always check the local laws in force. DISPOSE
OF THE PRODUCT RESPONSIBLY.
DISPOSING OF THE PRODUCT
Our products are made of various materials. Most of these materials (aluminum,
plastic, iron and electrical cables) are classified as solid urban waste. They
can be separated for recycling and disposed of at authorized waste treatment
plants. Other components (electronic boards, transmitter batteries, etc.) may
contain pollutants. These must be removed and disposed of by an authorized
waste disposal and recycling firm. It is always advisable to check the
specific laws that apply in your area. DISPOSE OF THE PRODUCT RESPONSIBLY.
PRODUCT DATA AND INFORMATION
Key
This symbol shows which parts to read carefully.
****This symbol shows which parts describe safety issues.
This symbol shows what to tell users.
The measurements, unless otherwise stated, are in millimeters
Description
801MS-0150
BXV04AGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 400 kg that are up to 14 m long. RAL7024 grey cover.
801MS-0180
BXV06AGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 600 kg that are up to 18 m long. RAL7024 grey cover.
801MS-0210
BXV08AGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 800 kg that are up to 20 m long. RAL7024 grey cover.
801MS-0230
BXV10AGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 1000 kg that are up to 20 m long. RAL7024 grey cover.
801MS-0260
BXV04RGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstacle detecting device for gates
weighing up to 400 kg that are up to 14-m long. RAL7024-grey cover.
801MS-0270
BXV06RGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 600 kg that are up to 18 m long. RAL7024 grey cover.
801MS-0280
BXV08RGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstacle detecting device for gates
weighing up to 800 kg that are up to 20-m long. RAL7024-grey cover.
801MS-0290
BXV10RGS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 1000 kg that are up to 20 m long. RAL7024 grey cover.
801MS-0380
BXV06AGM – Operator with 24 V motor, featuring a control board with display,
equipped with magnetic limit switches, on-board radio decoding, movement and
obstacle detecting device for gates weighing up to 600 kg that are up to 18-m
long. RAL7024-grey cover.
801MS-0390
BXV10AGM – Operator with 24 V motor, featuring a control board with display,
equipped with magnetic limit switches, on-board radio decoding, movement and
obstacle detecting device for gates weighing up to 1,000 kg that are up to
20-m long. RAL7024-grey cover.
801MS-0151
BXV04ALS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstacle detecting device for gates
weighing up to 400 kg that are up to 14-m long. RAL 7040 grey cover.
801MS-0181
BXV06ALS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstacle detecting device for gates
weighing up to 600 kg that are up to 18-m long. RAL7040-grey cover.
801MS-0211
BXV08ALS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstruction detecting device for gates
weighing up to 800 kg that are up to 20 m long. RAL7040 grey cover.
801MS-0231
BXV10ALS – Operator with 24 V motor, featuring a control board with display,
on-board radio decoding, movement and obstacle detecting device for gates
weighing up to 1000 kg that are up to 20-m long. RAL7040-grey cover.
Intended use
Sliding gate solution for residential buildings and apartment blocks
Any installation and/or use other than that specified in this manual is
forbidden.
Description of parts
Operator 1 Cover
- Cover
- Board-holder support
- Gearmotor
- Anchoring plate
- Housing for two emergency batteries
- Transformer
- Mechanical limit switch
- Release cord hole
- Housing for the RGP1 module
- Housing for thermostat with cartridge
- Board protection cover
- Control board
- Control board holder
- Housing for the RLB card
- Housing for UR042 module
- Housing for SMA or RGSM001 sensor
- Release lever
- Lock
- Mechanical limit-switch tabs
- Magnetic limit switch
- Magnetic limit-switch tabs
- Ferrite
*Only for BXV06AGM and BXV10AGM
MODELS| BXVO4AGS BXVO6AGS| BXVO8AGS| BXV1 OAGS|
BXVO4RGS BXVO6RGS BXVO8RGS| BXV1 ORGS
---|---|---|---|---|---
Pinion module| 4 4| 4| 4| 4
4 4| 4
Maximum gate-leaf length (m)| 14 18| 20| 20| 14
18 20| 20
Maximum gate-leaf weight (kg)| 400 600| 800| 1000| 400
600 800| 1000
MODELS| BXVO6AGM| BXV1 OAGM| BXVO4ALS| BXVO6ALS
BXVO8ALS| BXV1 OALS
Pinion module| 4| 4| 4| 4 4| 4
Maximum gate-leaf length (m)| 18| 20| 14| 18
20| 20
Maximum gate-leaf weight (kg)| 600| 1000| 400| 600
800| 1000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>