perle S-1110HP-SFP Hi PoE Media Converters Owner’s Manual

perle S-1110HP-SFP Hi PoE Media Converters Owner’s Manual

perle.com/products/media-converters/s-1110hp-sfp-hi-poe-media- converters.shtml

IEEE 802.3bt Compliant PoE & Fiber Media Conversion

• 10/100/1000Base-T to 100/1000Base-X Fiber
• 1 or 2 empty slots for Cisco and other industry standard SFPs
• Supplies IEEE 802.3bt Hi-PoE PSE (up to 100W) power
• Compatible with IEEE 802.3af PoE and IEEE 802.3at PoE+ PoEdevices
• Dual or Single 10/100/1000Base-T PoE ports
• Advanced features: PD Reset, Fiber redundancy, Smart Link Pass-Through, Fiber Fault Alert,Auto-MDIX and Loopback

Perle S-1110HP-SFP Fiber Media Converters transparently connect copper to fiber while providing up to100 Watts of IEEE 802.3bt compliant Hi-PoE PSE power to standards-based compliant devices such aspan-tilt-zoom (PTZ) security cameras with heaters, LED lighting in building management, and 802.11ax/acwireless access points.

Perle Hi-PoE Media Converters are classified as Power Sourcing Equipment (PSE). While using standardUTP cables that carry Ethernet data, Perle Hi-PoE media converters provide power to Powered Devices(PDs) that support the IEEE 802.3bt PoE standard (up to 100W of power) or pre-standard solutionsincluding UPoE, 4PPoE, PoE++, UltraPoE, 4 Pair PoE, etc. As this standard is fully backwards compatiblewith the existing IEEE 802.3af PoE and IEEE 802.3at PoE+ standards, all of those PD’s are alsosupported. The S-1110HP-SFP Fiber Media Converter features single or dual 10/100/1000Base-T RJ45ports to power one or two PD’s per converter. Learn more about PoE

And, with one or two empty transceiver ports on the S-1110HP-SFP Fiber Media Converter, flexiblenetwork configurations requirements can be meet using a variety of
transceivers supplied by Perle , Cisco ,or other manufacturers of MSA compliant SFPs.

• extend the life of non-fiber based equipment by enabling data transmission from 10/100/1000Base-T devices over 100/1000Base-X fiber
• extend the distance of an existing network by linking CAT5/6/7 cabling to multimode or single modefiber
• protect Ethernet data from EMI noise and interference by inter-connecting your copper-Ethernetdevices over fiber.

Network Administrators can “see-everything” with Perle’s advanced features such as Auto-Negotiation,Auto-MDIX, Link Pass-Through, Fiber Fault Alert, and Loopback. This allows for more efficienttroubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetimewarranty and free worldwide technical support, make Perle S-1110HP-SFP PoE Media Converters thesmart choice for IT professionals.

S-1110HP-SFP-XT PoE Media Converters are also available with support for -40C to +75C (-40F to+167F) extended operating temperature ranges

S-1110HP-SFP Hi-PoE Media Converter Features

Gigabit Fiber to IP Cameras

Connect 10/100/1000 IP Cameras to Gigabit Backbone
Extend the reach to IP cameras using fiber media converters. Security cameras are typically installed inremote locations throughout a facility. For cameras that are in the ceiling or other inaccessible areaslike rooftops, light poles, along fences, pipelines and transit routes, the cost of bringing electrical powerto each camera is eliminated by powering the equipment through the UTP cable using a PoE mediaconverter. Cameras with features like Pan-Tilt-Zoom ( PTZ), heaters, de-icers, or blowers generallyrequire higher power (30-100 Watts), making the Perle S-1110HP PoE Media Converters the idealsolution.

Fiber is run from an existing data closet to an area with access to power. The Hi-PoE Media Convertercan be powered by 57vDC or standard 100 to 240 AC power. The media converter is attached to thepower supply and the fiber cable. Copper (UTP or STP cable) Ethernet can be extended another 100meters to the IP camera. The Hi-PoE Media Converter is converting the data from fiber to copper,adding power and transmitting it to the security camera.

To simplify cabling, multiport PoE media converters enable chaining, with a fiber uplink port and a fiberdownlink port, of the fiber between media converters ( also known as a bus architecture ).

A second option is to have redundant fiber links for installations requiring fiber facility protection. Thereis an active fiber port and a protection fiber port that can support a fiber failure switchover of less than 50 milliseconds. The Hi-PoE media converter supplies power to the camera, and has power protectionfrom an Uninterruptible Power Supply (UPS) battery back-up. In the event of a fiber cut and a loss ofpower, the camera continues to send data on the protection link.

Gigabit Fiber to Wireless Access Points

Connect 10/100/1000 Wireless Access Points to Gigabit Backbone
Extend the reach to wireless access points ( AP ) using fiber media converters. When a companydeploys a wireless network in their office or large warehouse, APs need to be set up throughout thefacility to ensure complete coverage for reliability. The network manager will likely need to extendfurther than the 100 meters allowed by copper cable to reach many of the APs.

For wireless access points that require 30-100 Watts, such as those meeting the 802.11ax standard,802.11ac standard or containing dual radios, the Perle S-1110HP PoE Media Converter is the idealsolution.

Fiber is run from an existing data closet to an area with access to power. The Hi-PoE Media Convertercan be powered by 57vDC or standard 100 to 240 AC power. The media converter is attached to thepower supply and the fiber cable. Copper (UTP or STP cable) Ethernet can be extended another 100meters to the Wireless Access Point. The Hi-PoE Media Converter is converting the data from fiber tocopper, adding power and transmitting it to the WAP.

To simplify cabling, multiport PoE media converters enable chaining, with a fiber uplink port and a fiberdownlink port, of the fiber between media converters ( also known as a bus architecture ).

A second option is to have redundant fiber links for installations requiring fiber facility protection. Thereis an active fiber port and a protection fiber port that can support a fiber failure switchover of less than50 milliseconds. The PoE+ media converter supplies power to the camera, and has power protectionfrom an Uninterruptible Power Supply (UPS) battery back-up. In the event of a fiber cut and a loss ofpower, the camera continues to send data on the protection link.

Gigabit Fiber to the Desktop / VoIP ( Voice over IP ) Phones

Connect 10/100/1000 workstations and VoIP Phones to a Gigabit Backbone
Extend the reach to your workstation and VoIP phones using fiber media converters. For VoIP phonesthat require 30-100 Watts power, such as those containing dual radios, the Perle S-1110HP PoE MediaConverter is the ideal solution.

Fiber is run from an existing data closet to an area with access to power. The Hi-PoE Media Convertercan be powered by 57vDC or standard 100 to 240 AC power. The media converter is attached to thepower supply and the fiber cable. Copper (UTP or STP cable) Ethernet can be extended another 100meters to the IP Phone. The Hi-PoE Media Converter is converting the data from fiber to copper,adding power and transmitting it to the IP Phone.

Redundant Dual-Fiber Uplink

Assured Fiber Uplink Connectivity for your critical equipment
When extending the reach of your critical Ethernet equipment using fiber media converters, a dual fiberport media converter with Fiber Redundancy capability provides a fast switch-over of link traffic fromone fiber connection to the other converters.

Two modes of operation are possible.;

1. Redundant Fiber
   : When the primary link fails, the media converter redirects traffic to the other fiberport within 50ms.

2. Redundant Primary
: When the primary link fails, the media converter redirects traffic to thesecondary fiber port within 50ms. Upon restoration of the primary fiber link, traffic is automaticallyredirected back to the primary fiber.

Single Mode / Single Fiber
Connect copper ports over a single fiber strand ( also referred to as “Bi- Directional” BiDi )
When Single Strand fiber is used, a pair of Single Fiber Media Converters is needed for the copper to fiber conversion. Perle Single Fiber Media Converters are also referred to as “Up/Down” models. For example the S-1110HP-SC05 U (“Up”) and S-1110HP-SC05 D (“Down”), shown below, must be used in pairs. An “ Up” must be matched with a “ Down” peer to deal with transmit and receive frequencies separately.

S-1110HP-SC05U
S-1110HP-SC05D
The majority of installations for single mode fiber media converters are of the “dual connector” or “dualfiber” type where one fiber connection is used for transmit, the other for receive. These are physically“crossed” to match up the Transmit/Receive links.

However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized.WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDMtechnology relies on the fact that optical fibers can carry many wavelengths of light simultaneouslywithout interaction between each wavelength. Thus, a single fiber can carry many separate wavelengthsignals or channels simultaneously.

So remember, if Single Strand fiber is used, you will need an “ Up ” Media Converter on one side and a“ Down ” Media Converter on the other for copper to fiber conversion.

Accessories

Copyright © 1996 – 2022 Perle. All Rights Reserved

Read More About This Manual & Download PDF:

References

• S-1110HP-SFP Fiber Media Converters with Hi-PoE PSE (up to 100W)
• Environmental Policy | Fiber & Serial to Ethernet | Perle
• Contact Us | Reliable Device Networking Hardware | Perle
• Media Converters | Link Fiber and Copper Networks | Perle
• S-1110HP-SFP Fiber Media Converters with Hi-PoE PSE (up to 100W)
• S-1110HP-SFP-XT Fiber Media Converters w/ Hi-PoE PSE (up to 100W)
• Cisco SFP Support Technical Note | Perle
• Link Pass-Through | Ethernet to Fiber Tech Note | Perle
• Power Over Ethernet (PoE) Background | Technical Note | Perle

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>