GRENNIX G900 Robotic Pool Vacuum User Manual

GRENNIX G900 Robotic Pool Vacuum

Product Information

Model: G900

The Grennix G900 is a cordless robotic pool cleaner designed for easy and effective pool cleaning. It is suitable for all shapes of pools, including flat-bottomed inground pools and above ground pools. With its compact and lightweight design, the G900 delivers a more thorough and perfect cleaning result at an affordable price.

Features:

• Compact and lightweight design
• Suitable for all pool shapes
• Cordless operation
• Effective and deep cleaning
• Affordable price

Usage Instructions

Safety Instructions

Caution: When using the Grennix G900, do not enter the water or get close to the cleaner to prevent accidents. The operator must monitor on-site and give prompts and warnings. Our company will not be responsible for any liabilities caused if the operator fails to do so.

Installation Grennix G900

Follow the steps below to install the Grennix G900:

1. Turn off the cleaner before installation.
2. Place the cleaner gently on the water surface, bottom side down.
3. Wait for the cleaner to automatically sink to the pool bottom.

Charging

Before first use, make sure to charge the cleaner. Follow these instructions:

1. Turn off the cleaner before charging.
2. Place the cleaner on a flat surface and ensure the water spray cover does not touch the ground.
3. Observe the indicator on the charger:
   • Green light: Charger plugged into the power supply, not plugged into the product.
   • Red light: The cleaner is charging.
   • Red light to Green light: Cleaner finishes charging.

Entering the Pool

To enter the pool with the cleaner, follow these steps:

1. Turn the cleaner upside down and press the power switch. The cleaner will turn on with continuous regular beeping.
2. Put the cleaner on its bottom.
3. Grab the handle and gently place the cleaner on the water surface.
4. Wait for the cleaner to automatically sink to the pool bottom.

Getting out of the Pool

To remove the cleaner from the pool, follow these instructions:

1. Install the retrieval hook on the pick-up rod (not included in the package).
2. Use the retrieval hook to grab the handle and drag the cleaner out of the water (do not drag too fast).
3. Take the cleaner out after the water inside the device is completely drained.
4. Turn off the cleaner.
   • Note: After the device is out of water, if a short beep is heard every 3 seconds, turn off the device immediately. If a short, rush, and loud beep is heard, turn off the device and charge it immediately.

For more information, refer to the complete user manual or contact Grennix customer support at +1 800-279-9986.

Product Introduction

Model: Grennix G900
Features: Grennix G900 cordless robotic pool cleaner is well-designed for use in any situation without any hassle. Thanks to the compact and lightweight design, it is suitable for all shapes of pools. It can clean flat-bottomed inground pools and above ground pools. With an affordable price, it delivers a more effective, deeper and perfect cleaning result.

Thank you for choosing Grennix G900.
Please keep this manual in a safe place for future reference.
Read this manual carefully before use and follow the instructions.

Safety Instructions

1. Read this manual carefully and use Grennix G900 robotic pool vacuum accordingly. We are not liable for any loss or injury caused by improper use of the device.
2. G900 pool vacuum is only intended for use on flat-bottomed inground pools and above ground pools.
3. Before using G900, ensure the water depth of the pool is at least 50cm away from the top of it.
4. Keep humans and animals out of the pool while the device is working in it. Do not leave children unsupervised and near the pool while G900 is working.
5. Turn off G900 before cleaning the filter.
6. G900 comes with a built-in lithium battery. Do not disassemble the sealed compartment without authorization. Protect G900 pool vacuum from direct sunlight and strong impacts.
7. Be sure to charge G900 before first use.
8. During the idle period, charge G900 once a month to protect its battery.
9. Grennix G900 is suitable for pH [7.0-7.8], temperature [4-34 °C], chlorine [max. 4.0 ppm], sodium chloride [max. 5,000 ppm].

• is a Caution sign;
• is a Warning sign

Overview

Accessories

Specifications

1. Dimensions (L x W x H): 350 x 350 x212mm
2. Weight: 3.2 kg / 7.05 lb
3. Battery capacity: 2,600mAh
4. Battery life: 60-75mins
5. Motor power: 20W
6. Charging time: 2.3hours
7. Power adapter/Input voltage: 100-240V
8. Power adapter/Output voltage: 12.6V
9. Power adapter/Rated power: 19.8W
10. Operating temperature: 0 to 35℃
11. Storage temperature: -10 to 40℃
12. Filter density: 180μm
13. Water depth supported: 0.5-3m
14. Moving speed: 0.35m/s
15. Waterproof level: IP68
16. PH value supported: 7.0~7.8

Helpful tips

1. Turn off the cleaner after it gets out of water.
2. After the cleaner finishes cleaning, it is recommended to dry in the shade for 20 minutes before charging. Place the cleaner in the shade when charging. Do not cover the device with anything to prevent damage to the internal components caused by overheating.
3. When the battery is low, the device automatically moves to the pool edge and stops working. The buzzer generates a beep after the device is taken out.
4. After each use, rinse off residual pool water and internal debris in the device and place the device in a cool and dry place, and away from heat sources.
5. Clean or replace the filter if the cleaning effect is found to be weakened.
6. This device cannot climb. Put it into the water area which is away from steps.
7. For the best cleaning results, please make sure to clean the filter more than once during the robot working process.

Operation

When Grennix G900 is working, do not enter the water or get close to the cleaner to prevent accidents. The operator must monitor on site and give prompts and warnings. Our company won’t be responsible for the liabilities caused if the operator fails to do so.

Installation Grennix G900

1. Open the top lid: Place your thumb on the top lid near the clasp. Pull the lower end of the clasp away by 2 millimeters with other fingers. Lift the top lid with both hands together.
2. Open the filter basket: Gently lift the filter basket when grasping two handles of filter basket with both hands.
3. Install the filter screen: Press down the filter screen to make them fit when four posts of screen are aligned with the slots in the base.
4. Install the top lid: Lift the handle of the top lid and align the top lid with the upper and lower slots to install. At the end, press the top lid firmly after installation to make the top lid of cleaner and the base completely fit.

Charging

Be sure to charge the cleaner before first use. Turn off before charging. The water spray cover should not touch the ground when placing the cleaner.

Observe the indicator on the charger:

1. Green light: Charger plugged into the power supply, not plugged into the product.
2. Red light: The cleaner is charging.
3. From Red light to Green light: Cleaner finishes charging.
4. The water spray cover should not touch the ground when placing the cleaner.

Entering the pool

Be sure to charge the cleaner before first use.

1. Turn the cleaner upside down and press the power switch. The cleaner is turned on with continuous regular beeping.
2. Put the cleaner on its bottom.
3. Grab the handle and place the cleaner gently on the water surface.
4. Wait for the cleaner to automatically sink to the pool bottom.

Getting out of the pool

Install the retrieval hook on the pick-up rod (the rod is not included in the package). Be careful when using it. Make sure the device is turned off when it is not in use.

1. Use the retrieval hook to grab the handle and drag the cleaner out of the water (do not drag too fast).
2. Take the cleaner out after the water inside the device is drained completely.
3. Turn the cleaner off.

Note: After the device is out of water, if a short beep is heard every 3s, turn off the device immediately; if a short, rush and loud beep is heard, turn off the device and charge it immediately.

Cleaning

1. Gently force apart both sides of the buckle and slightly shake the cleaner to separate the stand from the upper part of the cleaner body. Lift the upper part of the body.
2. Remove the filter to expose the garbage.
3. Rinse the residual garbage on the filter.
4. Rinse the residual garbage on the bottom.

FAQs

In case of any problems other than those described above, please contact us to avoid unnecessary losses.

• Q: Why my G900 doesn’t work when it’s put into water?

1.  **A:** Please check whether the switch of G900 is in correct condition. When you release your hand after pressing the power-on button, if you still can hear the beep noise every second, it means the machine has been switched on. If the machine no longer make beep noise after you release your hand, it means the machine has been switched off, please press the power-on button firmly until the machine is switched on.
2. Check whether the battery level is too low (red lights flashes slowly and continue one minute).
3. Check whether G900 is stuck or trapped in the corner.

• Q: How to solve the problem that the speed of G900 be slow or stopped after working for a while?

1.  **A:** If G900’s speed gets slower or stopped while using, it maybe caused by overload of filter. Please clean out the garbage and put it back to the pool to continue cleaning without recharging.

• Q: What kind of telescopic pole do I need to install for the retrieval hook?

1.  **A:** G900 requires a universal connector pick-up pole that the diameter is of 1-1/4″, which is a universal size to fit standard size pool accessories.
2. There’s no pick-up pole in G900’s package.

• Q: What’s the optimum usage for G900?

1.  **A:** Perfect for in-ground pool and above-ground pool in flat ground.
2. Suitable for the pool that the slope gradient is less than 10°.
3. Suitable for the pool that the size is less than 645 square footage.

• Q: What kind of pool that G900 doesn’t support?

1.  **A:** G900 can’t climb walls or steps, can’t clean floating algae or very large leaves.
2.  Pool with wrinkles that exceed 10 millimeters or slope gradient exceeds 10° (Machine will be stuck).
3. Large pool that the size is over 645 square footage.

• Q: How many indicator lights that G900 has?

1.  **A:** Green light of charger: When the charger is plugged into power supply.
2.  **Red light of charger:** The product is in process of being charged.
3.  **Green light of charger:** Product charging completed.
4.  **Blue light of product base:** The machine is switched on successfully, start working.
5.  **Red light of product base:** The battery level is low.

• Q: What the cue voice of G900 indicates?

1.  **A:** Successful power-on: Beep with regular ticking.
2. Low battery level: Long beep.

• Q: Why there’s long beep while charging?

1.  **A:** This is the warning voice of power-on charging. Please turn off the machine before charging.

Cautions

1. It’s normal that G900’s speed gets slower or stopped within several minutes when it’s put into dirty pool. It maybe caused by overload of filter. Please clean out the garbage in the filter and reinstall the filter into G900, then put G900 back to the pool to continue work.
2. The charging port of product base is IP68 waterproof, which can be put into water directly.
3. Please keep all charging port dry before charging.

Warranty

This product has passed all safety tests and quality control, conducted by the technical department of factory.

Warranty Information

1. The warranty is covered for 12 months (only for motor and battery) from the date of original purchase.
2. This warranty is voided if the product has been altered, misused, or has beenrepaired by unauthorized personnels.
3. The warranty extends only to manufacturing defects and does not cover anydamage resulting from mishandling of the product by the owner.
4. The order number or record must be presented for any claim or repair duringthe warranty period.

Contact

Scan the QR code for more details.

• www.grennix.com
• support@grennix.com

Grennix Robotic Pool Cleaner

• Tel: +1 800-279-9986
• Website: www.grennix.com
• E-mail: support@grennix.com
• Work time: Mon-Fri, 09:00-18:00 (EST)
• Manufacturer: Shenzhen Tema Information Technology Co., Ltd.
• Address: 702, Tianshu Block, Tongchuang X Star Space, No.6099 Baoan Avenue, Xinhe Community, Fuhai Street, Baoan District, Shenzhen, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>