Crystalfontz CFA800480E3 5 Touchscreen EVE Development Kit User Guide
- June 12, 2024
- Crystalfontz
Table of Contents
Crystalfontz CFA800480E3 5 Touchscreen EVE Development Kit
Product Information
| Product Name | Crystalfontz CFA800480E3-050SW-KIT |
|---|---|
| Quick Start Guide | [Link to |
Quick Start Guide](https://www.crystalfontz.com/product/cfa800480e3050swkit)
Kit Contents| Display module, Breakout board, flat flex cable
Additional Requirements| A 5V power supply (such as your computer), USB cable
(such as
WRUSB27)
Further Information| Visit the Crystalfontz
website for full
product datasheets and programming
examples.
Contact Information| Crystalfontz America, Inc.
12412 East Saltese Avenue Spokane Valley, WA 99216-0357
Phone: 888-206-9720
Fax: 509-892-1203
Email: support@crystalfontz.com
URL: www.crystalfontz.com
Product Usage Instructions
- Step 1: Connect the display module to the Breakout board using the flat flex cable, as shown below. The blue cable end should face upwards on both the display and breakout board.
- Open connector. It flips up, it does not slide.
- Slide in FFC.
- Rotate lockdown to secure FFC.
- Step 2: The Seeeduino should already be connected to the Breakout board using jumper cables. If any cables have become disconnected, reconnect them according to the provided diagram.
- Step 3: Ensure the voltage selection switch on the Seeeduino is set at 3.3V.
- Step 4: Make sure the boards are physically separated to avoid short circuits. Connect the Seeeduino to a 5V power supply using the included USB cable. The power supply can be a computer, bench supply, plug-pack style power supply, or similar.
- Step 5: The display should now be lit and display a demonstration program.
Kit Contents
- 1x Crystalfontz CFA800480E3-050SW display module
- 1x Crystalfontz CFA10098 Breakout board
- 1x Seeed Studio’s Seeeduino development board (pre-programmed)
- 1x Crystalfontz WRFFCY50 flat flex cable
- 9x Crystalfontz individual WRJMPY40 female-female jumper cables
Also required: A 5v power supply (such as your computer) and a USB cable (such as WRUSB27)
Quick Start
-
Step 1 –
Connect the display module to the Breakout board using the flat flex cable, as shown below. The blue cable end is faced upwards on both the display and breakout board. -
Step 2 –
The Seeeduino is supplied pre-connected to the Breakout board using jumper cables. If any of the cables have accidentally become disconnected, reconnect as per the following diagram. -
Step 3 –
Make sure the voltage selection switch on the Seeeduino is set at 3.3V. -
Step 4 –
Ensure the boards are physically separated to avoid short circuits.
Connect the Seeeduino to a 5V power supply using the included USB cable.
The 5V power supply can be a computer, bench supply, a plug-pack style power supply, or similar. -
Step 5 –
The display should now be lit, and displaying a demonstration program.
Further Information
See the Crystalfontz website for further information including full product
datasheets and programming examples:
https://www.crystalfontz.com/product/cfa800480e3050swkit
We’re here to help! Email your questions to
support@crystalfontz.com or post at
forum.crystalfontz.com
We’d love to hear about your project! Tag us on Facebook, Instagram, LinkedIn,
Twitter, or YouTube, or send us a link to your project on the web!
Crystalfontz America, Inc.
12412 East Saltese Avenue
Spokane Valley, WA 99216-0357
Phone : 888-206-9720
Fax : 509-892-1203
Email : support@crystalfontz.com
URL : www.crystalfontz.com
References
- Crystalfontz LCD Forum
- Crystalfontz LCDs, OLEDs, ePaper & TFT Displays
- Crystalfontz LCDs, OLEDs, ePaper & TFT Displays
- 5" Touchscreen EVE Development Kit from Crystalfontz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>