Infracomfort JW Series High Power Infrared Radiant Heater Owner’s Manual

Infracomfort JW Series High Power Infrared Radiant Heater

Product Information

• Product Name: High Power Infrared Radiant Heater
• Model: JW Series
• Features:
• Comfortable: No wind, light or odor will be caused during the running of this product, so the indoor air is clean without floating dust.
• Energy-saving: High heat generation and excellent heat distribution, use less energy than traditional heating methods.
• Reliable: The indoor temperature can be adjusted freely, free of the limitation of heating season.
• Working Condition:
  • Ambient temperature: -30 ~ +40
  • Rated Voltage: 220-240V~
  • Rated frequency: 50Hz/60Hz
  • Relative humidity: less than 95%

Product Usage Instructions

1. Read all instructions carefully before setting up and operating this unit.
2. Ensure safety precautions are followed to avoid accidents or personal injury.
3. Avoid inserting any metal or foreign objects inside the radiant heater.
4. Avoid splashing water into the radiant heater.
5. Connect the adjusting bracket to the sliding bracket for installation.
6. Fix the adjusting bracket into the wall using expansion screws.
7. Make sure to install two adjusting brackets and lock them tightly using butterfly hand screws.
8. Use the manual key or remote controller to turn on/off the heater and adjust the heating level.
9. Use the fast hot button to activate or deactivate the rapid heating function.

READ AND SAVE THESE INSTRUCTIONS
Read all instructions carefully before setting up and operating this unit. This manual is designed to provide you with important information needed to setup, operate, maintain for your radiant heaters. Failure to follow these instructions may damage and/or impair its operation and void the warranty.

SAFETY PRECAUTIONS

This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
WARNING: In order to avoid overheating, do not cover the heater.

1. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
2. The heater must not be located immediately below a socket outlet.
3. Do not use the same socket together with other appliances, in case of current overload. Make sure the plug and socket good contact.
4. Please pull plugs out when power off. Do not pull wires by hands.
5. Please stop power immediately once heaters failure or wires arc broken. Users can not repair heaters by themselves. Please contact authorized servicer for maintenance if heaters failure.
6. Radiant heater cannot be placed directly below the power outlet.
7. Radiant heater surface temperature is high, must be installed higher than 22 meters above ground.
8. Radiant heater surface cannot be covered and cannot hang objects on equipment.
9. The distance between back of radiant heater and roof should be larger than 150mm，cannot place objects within 1000mm distance in front of radiant heater, the side should be kept at least 200mm away from the surrounding space.
10. Must cut off power and wait till equipment surface cool before cleaning, flushed by water is prohibited.
11. Users cannot repair the radiant heater，if equipment failure and need maintenance, please contact authorized servicer.
12. Do not install and use radiant heaters on areas occur with flammable, explosive, easy to shock.
13. Please do not insert any metal or foreign objects to inside of radiant heater, to avoid accident or personal injury.
14. Radiant heater panel surface with high temperature, the surface temperature can reach to >50℃~386℃，touch is forbidden，beware of scalding accident.
15. Do not splash water into radiant heater to avoid accidents.

FOREWORD
Thank you for your trust and support in choosing the Infrared Heater, please read the instructions carefully before operating product.

INFRARED HEATER THEORY

Far-infrared radiant heaters are produced by unique design and manufacturing technique. Using a specially coated aluminum panel, the heat generated by the heating element is transferred radiantly to people and objects with maximum efficiency. The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture etc., like sunshine. Infrared heating will not lead to air movement, making the air cleaner, as dust and particles are not disturbed and circulated. Traditional convection heating relies on air movement to distribute the heat. The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to the warmth felt from the sun.

PERFORMANCE FEATURES

• Comfortable:
  No wind, light or odor will be caused during the running of this product, so the indoor air is clean without floating dust.

• Energy-saving:
  High heat generation and excellent heat distribution, use less energy than traditional heating methods.

• Reliable:
  The indoor temperature can be adjusted freely, free of the limitation of heating season.

• Physical therapy:

  • The heat radiant can change body microcirculation, cell organization under skin producing resonance, clearing the barrier of microcirculation, adjusting and balancing nervous system, promoting metabolism, increasing body physical power.
  • It is very good for people’s health.
  • Far-infrared radiant heaters are produced by unique design and manufacturing technique.
  • Using a specially coated aluminum panel, the heat generated by the heating element is transferred radiantly to people and objects with maximum efficiency.
  • The heat radiated from the panel surface, is absorbed by people, walls, floors, and furniture et cetera, like sunshine.
  • Infrared heating will not lead to air movement, making the air cleaner, as dust and particles are not disturbed and circulated.
  • Traditional convection heating relies on air movement to distribute the heat.
  • The air remains less humid, and gives you a sense of fresh, comfortable, warmth-similar to the warmth felt from the sun.

WORKING CONDITION

• Ambient temperature: -30℃ ~ +40℃
• Rated Voltage: 220-240V~
• Rated frequency: 50Hz/60Hz
• Relative humidity: less than 95%

INSTALLATION REQUIREMENTS

1. Qualified installer:
   The installation must be carried out by trained personnel.

2. Installation conditions:

3. Supply voltage fluctuation range should be within ± 10%,If not, please revise before installation.

4. If there is a serious security risk in users’ electricity environment, the installation should be refused, until eliminate the security risks.

5. Electricity lines should be equipped with earth leakage protection devices and master switch.

6. Ground wire should be connected to the grounding device on the building, if not, please consult to professional installer, please do not put ground wire to gas pipe, water pipe, lightning rod or telephone grounding wire.
   Model No.| Power(W)| Rated Current(A)| Voltage(V)| Cable length(mm)
   ---|---|---|---|---
   JH-10W| 1000| 4.3| 220-240| 2000
   JH-18W| 1800| 7.8| 220-240| 2000
   JH-24W| 2400| 10.4| 220-240| 2000
   JH-32W| 3200| 13.9| 220-240| 500

INSTALLATION INSTRUCTION

• Step 1: Remove packing of both ends of heater.
• Step 2: Connect adjusting bracket to sliding bracket.
• Step 3: Installation of sliding bracket & heater, as arrow points.
• Step 4: Fix adjusting bracket into the wall by expansion screws.
• Step 5: Installation of two adjusting brackets; make sure lock brackets tight by butterfly hand screw.

INSTALLATION DIAGRAM

DISPLAY INTERFACE

• Manual Key
  Press Manual Key button to turn on/off the heater, and set the heating level. Long press Manual Key to pair the Wi-Fi network(details as chapter 11).

• Indoor temperature sensor
  Using it to collect indoor temperature.

MANUAL FOR REMOTE CONTROLLER

1. ON/OFF button
   Press ON/OFF button to turn on/off heater.

2. Clock button
   Remote is powered on(as show in picture 2-1), present time is 00:00, time setting as follow:

3. Press clock button, the hour will flash(as show in picture 2-2), press up or down button to change hour setting.

4. Press clock button, the minute will flash(as show in pictures 2-3), press up or down button to change hour setting.

5. Press clock button, the second will flash(as show in picture 2-4), press up or down button to change hour setting.

6. Press clock button again, the second stop flashing and the setting is finished.

7. Heat button
   Press level button to adjust the power when the heater is on(as show in picture 3-1).

8. Fast hot button
   Press fast hot button to turn on/off fast hot function.
   Fast hot function is to let the heater run at full power for a certain time, to achieve the purpose of rapid heating.

9. Timer on button

10. Press timer on button, it will show ON–:–(as show in picture 5-1).

11. Press up or down to change hour(as show in picture 5-2).

12. Press time on button again, hour stop shining and minute begin to shine, press up or down to change minute(as show in picture 5-3).

13. Press time on button again, timer on function finished. It will show the present time 16;30 and on. Time on setting finished(as show in picture 5-4).

14. Timer off

15. Press timer off button, it will show off–:–(as show in picture 6-1).

16. Press up or down to change hour(as show in picture 6-2).

17. Press time off button again, hour stop shining and minute begin to shine, press up or down to change minute(as show in picture 6-3).

18. Press time off button again, timer off function finished. It will show the present time 16;30 and off. Timer off setting finished(as show in picture 6-4).

CONNECT TO NETWORK

1. Download Tuya Smart App
   Download Tuya Smart App from your smartphone (Google Play Store / App Store / AppGallery, etc.) or by scanning the following code. Or download Tuya Smart App from https://smartapp.tuya.com/tuyasmart

2. Register / Log in
   Register an account via mobile number or email address. Log in with existing account if an account has already been set.

3. Home management

4. Click “Start your smart life” to “Add family”

5. Manually set a family name at “Add family”. Set location at the map interface and change the location by coordinate point.

6. Click “Add Room” to add another room. By click “Done” to finish the room setting. And click “…” to proceed room management as needed. Click “Home Management” to add family. One account can simultaneously control several families by selecting available devices at the family management page.
   Click a family name to get into the “Family Settings” page and change the name, location and members as needed.

7. Add Devices
   Keep pressing Manual Key over 8 seconds after power on, till heater has beep sounds and icon of Wi-Fi flashing (twice per second).
   Click “add device” or “+” on the screen, find “Small Home Appliance”—“Heater”
   Press “Confirm indicator rapidly blink” and select a Wi-Fi signal nearby and enter Wi-Fi password to confirm the connection. Once the device added successfully, press “Done” to finish this procedure. If failed, you need to re-add or search for help.

8. Using App to control heater
   Once it’s connected, you can use the App to control the heater.

INSPECTION ITEMS AFTER INSTALLATION

Items to be checked| Situation caused by improperly i Items to be checked installation
---|---
Is installation stable?| The equipment may fall off or shake.
Is heat insulation adequate?| Damage objects close to equipment.
Does power voltage same as voltage shown on product nameplate?| Equipment failure.
Does wire connection correct?| Equipment failure.
Does electricity ground connected safely?| There is electricity leakage risk.

ATTENTION
Due to thermal expansion and contraction, the heater would make noise when turning on or off. It’s a normal phenomenon, and won’t make bad affection.

INSPECTION ITEMS FOR COMMISSIONING

1. Do not connect power until installation is complete.
2. All wires connection are correct and firm.
3. All scattered objects must be removed from radiant heater body.
4. Connect power and check heater is operating correctly.

PACKING LIST

SPECIFICATIONS

Model No.| Dimension(mm)| Package size(mm)| Net weight(kg)| Gross weight(kg)
---|---|---|---|---
JH-10W| 75518967| 820250150| 4.4| 5.5
JH-18W| 115518967| 1220250150| 6.9| 8.1
JH-24W| 165518967| 1720250150| 9.5| 11.3
JH-32W| 215518967| 2220250150| 12.3| 14.3

References

• Tuya Smart

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>