dexpro Feisty Compact High Speed Hand Dryer Instruction Manual
- June 12, 2024
- dexpro
Table of Contents
dexpro Feisty Compact High Speed Hand Dryer Instruction Manual
SAFETY WARNINGS
Before installing, be sure to read this installation manual and retain for future reference.
The electrical installation must be carried out by a qualified electrician in accordance with the latest edition of the IEE wiring regulations. Turn off the power at the main switch before inst
The dryer must not be installed on a flammable surface. Do not damage any parts of the electrical connections.
Electrical connection should be made to the fixed wiring of the property via a double pole switched fused spur. This product must be earthed.
Do not stall the dryer over a washbasin. If the power cord is damaged, it must be repaired by qualified personnel to avoid any type of risk
This dryer can be used by children aged 8 years and above. People with reduced physical, sensory or mental abilities or lack of experience and knowledge, if they have been given supervision and appropriate training regarding the use of the dryer in a safe manner, can use it with no restriction. Children should not play with the apparatus. Cleaning and maintenance performed by the owner should not be done without the children having supervision.
During use, temperatures above 158°F [70°C] may develop in the parts near the hot air nozzle Do not touch cover the dryer during use or when finished using it.
General safety information
WARNING: Installation of this product much be carried out by a qualified electrician and in accordance with the latest edition of the IEE wiring regulations.
WARNING: Isolate the power supply before any electrical work or wiring of the product.
DANGER This product must be earthed. Failure to properly earth the unit could result in electrical shock and / or death.
–NOTE: Do not install dryer over washbasin —
PACKING LIST
SPECIFICATION
Voltage: 220V-240V 50/60Hz,4A/1000W ONLY be used on same voltage as
product rated label marked.
Stand-by Power: Less than 2.0W
Air Temperature: 40°C[104°F](Distance from nozzle=100MM[4″],Room
Temp.=25°C[77°F])
BEFORE INSTALLATION
Installation must be carried out by a qualified electrician and in accordance with the latest edition of the IEE wiring regulations.
Electrical connection should be made to the fixed wiring of the property via a double pole switched fused spur.
INSTALLATION
- Isolate the power supply before any electrical work or wiring of the product.
- Place template against wall at desired height(see mounting height recommendations) and mark locations of 4 mounting holes Dia. 8mm(5/16″).
- Remove hand dryer back transportation only purpose screw.
- Remove and retain 2 side security hex cover screws and cover.
- Mount the hand dryer base on the wall.
- If the hand dryer is supplied in hardwired: a. Connect the live wire(Coloured Brown, Red, or Black) to the terminal block marked “L”. b. Connect the neutral wire(Coloured Black, Blue) to the terminal block marked “N”. c. Connect the ground wire (Coloured Green or Yellow) to the terminal block marked “E”.
- Before replacing cover, there is a customized option to run the dryer heater on (1000W) or heater off(600W). The switch is clearly marked.
- Default setting is 12-15CM from nozzle. If it needs and please adjust its range.
- Replace cover. Do not over-tighten screws.
- Connect the hand dryer plug to the power supply socket if needed then turn on power.
OPERATION
No-touch operation. There is a blue LED light to guide user to the air flow. Shake excess water from hands. Place hands under the outlet to start operation Rub hands lightly and rapidly. Stops automatically after hands are removed
Operation without touching, place your hands under the exit to activate the
device.
There is a blue LED light to guide the user towards the air flow.
After several seconds without detecting hands, the equip- ment stops automatically
ADJUSTMENTS
It is possible to turn on/off hot air with a switch located inside the unit
(see section 7 in “Insta- llation”).
It is possible to adjust the detection distance by means of the potentiometer located inside the unit (see section 8 in “Installation”).
MAINTENANCE
- Periodic cleaning of the unit is recommended.
- Remove cover and clean dryer dust lint.
- Wipe the cover with a damp cloth and mild cleaning solution. Do not soak.
- Never use abrasives to clean the cover.
DIAGNOSTICS & REMEDIES
| SYMPTOM | CORRECTIVE ACTION |
|---|---|
| Hand dryer fails to start | Ensure the breaker supplying the dryer is |
operational. Ifitis, disconnect the power and remove the hand dryer cover.
Check all the wire connection to sure they are well fixed. Turn on power and
if it does not work then replace circuit board Turn motor blower several times
by hand to see it is blocked.
Hand dryer turns onloff erratically or not sensitive enough| Ensure that there
is no obstruction on or in front of the infrared sensor zone. Clean any dirty
off the sensor lens. Try adjusting the sensitivity potentiometer on program
board I not still not work, replace circuit board and sensor board
Not hot air| Check if the heat element switch is power on. Check if the heat
element was broken. If yes, replace a new one.
Hand dryer makes ticking noise| Check the motor brush worn condition. Replace
them or a new motor.
WARRANTY
This hand dryer has a 1 year warranty from the date of purchase for any manufacturing defect. It covers replacement of defective parts, except when caused by improper use.
Before taking any action in the event of a fault, contact our customer service team who will assist you. The products serial number and proof of purchase must be provided. In the event of a faulty product, deXpro will replace faulty parts or atits sole discretion replace the product.
Labour costs and consequential losses are excluded.
MAINTENANCE
Periodic cleaning of the unit is recommended. Remove cover and clean dryer dust lint.
Cleaning stainless steel
Stainless steel is highly resistant to rust, but there are some very strict
cleaning and maintenance rules to be followed to prevent damage to its
appearance
General cleaning tips
Apply neutral detergents formulated for these purposes (non-ionic surfactants
and citric acid) Apply the detergent with soft cloth. Be careful with abrasive
cloths. They may scratch the surface Rinse with water until all the detergent
has gone Residue from hygiene products, liquid soap, shampoos, bath gel, etc,
can also damage surfaces Rinse the surface with plenty of water after use.
Limescale stains can be prevented by drying the surface with a soft cloth
after use.
Specific cleaning tips
Limescale from mains water: Apply a solution of one part vinegar and three parts water directly to the stains and leave to work for a few minutes. Then rub with a soft cloth or damp sponge. Then give ita final wash with plenty of water and neutral soap to ensure it is thoroughly rinsed. Unacceptable practices (loss of guarantee)
- Do not apply detergents with abrasive products or which contain: Hydrochloride acid Sodium hypocrite (bleach) Formic acid.
- Do not use abrasive utensils like metal sourcing pads or abrasive sponges.
- Do not spray the detergent on the surface, because the liquid can get into the openings or cracks in them and cause damage.
- Do not use anti-limescale and descaling cleaning products. They are not suitable for cleaning satin less steel.
- Do not use silver cleaners, contain chlorides that attach stainless steel.
Warning. Important to avoid (loss of guarantee)
Bleach and descalers are often applied to bathroom equipment and left to work
for a time. This leads to the release of gases that contain chloride, which
together with the water in the surface cause chlorides to run down the surface
of the stainless steel. This rusts both internal and external surfaces.
DIAGRAM BY STANDARD CIRCUIT BOARD
Power [Hardwired or Plug into Socket]
ONLY be used on same voltage as product rated label marked.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>