Ailofy AILSPR RGBIC Light Strip User Guide
- June 12, 2024
- Ailofy
Table of Contents
QUICK START GUIDE
SPECIFICATION
Model: AILSPR
Wireless connection: 802.11b/g/n;
1-14@2.4GHz; WPA/WPA2+20dBm
Adapter input: AC 110V-250V 50Hz/60Hz
Operating temperature: -4 ℉-122 ℉(-20 ℃-50 ℃)
Length: 16.4ft
Wattage: 24watts
Rated input: DC 12V
Life expectancy: 25,000 hours
Installation
Controller Installation
- Use an alcohol wipe to clean the surface of the sticking area.
- Remove the adhesive on the controller and stick it on the clean place.
Tip: Make sure the controller is glued firmly and the button on the side can
be used normally.
Light Strip Installation
- Use an alcohol wipe to clean the surface of the sticking area.
- Connect the light strip to the controller, then remove the adhesive backing on the light strip and stick it on the installation surface.
In the case of not connecting the power supply, the light strip can be cut to the required length at the cut line mark.
When the light strip needs to be installed at 90°, please fold the light strip
into a loop and fix it with clips.
Tip: Do not bend the light strip directly.
When powered on, the light strip flashes blue, if not, press and hold the side button for 7 seconds until the controller flashes blue and yellow.
Status Indicator
| Flashing blue & yellow | Solid blue |
|---|---|
| In pairing mode | Light strip on |
| Flashing blue | Off |
| Connecting to cloud or offline | Light strip off |
Connect
-
Download the Ailey app from your app store and sign up for a new account.
-
Follow the instructions in the Ailey app to setup.
-
Open the Ailey app and tap the + sign on the top right corner of the My Home tab. Tap Add Device and then select Ailey Light Strip Pro.
Connecting To Your Voice Assistant
Alexa
- Open the Ailey App, enter your Account settings, tap Smart Integrations.
- Tap Alexa to bind your Ailey account.
- When binding successfully, you can control your Ailey lights via Alexa.
Google Home
- Open the Gouge Home App, log in your account.
- Tap Set up device.
- Tap Works with google.
- Search the Ailey device listing and log in with our Ailey account.
- Wait a few more seconds, and you’re done.
Precautions
- Do not let the light strips get tangled together to avoid heating the light strips.
- It is forbidden to bend the position of the LED lamp, which may damage the product.
- Keep the device powered off during installation.
- If the power cord is damaged, please do not disassemble and repair it without permission.
- The product only be supported to use indoor.
FCC Warning
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
NEED HELP?
Service Email: support@ailofy.com
Service URL: www.ailofy.com