Solidny H100 Desk Mount with Gas Spring User Manual
- June 12, 2024
- Solidny
Table of Contents
Solidny H100 Desk Mount with Gas Spring
Introduction
Display size: 22″ – 35″
Max load : 2 – 12 kg
VESA: 75×75, 100×100 mm
Severe personal injury and property damage can result from improper installation or assembly Read the following warning carefully before beginning.
- Products must be installed by professional or installer.
- If you do not understand the instructions or have any concerns or questions, please contact a qualified local installer.
- Do not install or assemble if the product or hardware is damaged or missing, IF you require replacement parts, please contact you local distributor for assistance.
- This product fits most 22″-35″ LCD / monitor; maximum weight of LCD/ monitor: 12 kg.
- Installer-friendly and straight forward.
- For safe installation, the desk you are mounting to must support minimum 3 times the weight of the total load (the mount, the monitor and all accessories weight).
- Do not use this product for other than the original designed.
- This product contain moving parts, please use with caution.
- When installing monitor, please do not damage electrical wiring or power source.
- Installation and routing of monitor cables on the monitor bracket must comply with electro-technical regulations.
- Importantly, mains- and data-cables must be secured against twisting and squeezing or shearing.
- The manufacturer will bear no responsibility to the desk of mounting, or incidental or consequential damages arising there of.
- The manufacturer disclaims any liability for the modifications, improper installation, or installation over the specified weight range. The manufacturer will not be liable for any damages arising out of the use of , or inability to use, the product.
- This product is designed for indoor used only, use of this product outdoor could lead to product frailer and severe personal injury.
- This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned. In order to ensure the performance of gas spring, full direction adjustment of the product arm is recommended several times per month.
- All images are for reference only. As product in kind prevail.
We reserve the right to modify or alter instructions. No modification or alteration without formal notice.
What’s in the Box
Table edge Installation
Grommet Installation
Arm Installation
Cable routing
Display Installation
Torque adjustment
- If display can be hovered at any height after display installed. No adjustment needed.
- If display lift up automatically after display installed, adjust the following: One man hand press down the screen, the other wind set screw at the bottom of upper arm at joint to ‘ – ‘ direction to reduce torque by using F, 5mm. Allen key as shown in Fig-1 and 2 until display can be hovered at any point of positions.
- If display sit at the lowest position after installation, repeat #2 procedures but winding set screws to ‘ + ‘ direction to increase torque as Fig-1 and 2 until display can be hovered at any point of positions.
Setting tilt angles
Directional usage guide
Display rotation
Warning
Distributors
|
ERGOSOLID SARL
36 rue du Louvre
75001 Paris, France
Tel. (+33)7 72 15 51 60
www.ergosolid.fr
---|---
|
Ergosolld Italia S.R.L
Via Giosue Carducci
32 – 20123 Milano, Italia
Tel. +39 02 5656 8661
www.ergosolid.it
|
Ergosolid sp. k.
ul. Boya i:elenskiego 15
35-105 Rzesz6w, Poland
tel. +48 17 785 23 71
www.ergosolid.pl
Customer Support
Fiber Novelty
ul. Boya Zelenskiego 15
35-105 Rzesz6w, Poland
tel. +48 17 787 60 70
www.fibernovelty.pl
Kunshan Hongjie Electronics Co., Ltd.
1050, FuChunJiangRoad, Economic Development Zone
Kunshan City, Jiangsu Province. China. 215333
Mail : info@nbavmount.com
Website : www.new-nb.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>