Infinix X6835B Hot 30 Play Smartphone User Manual

June 12, 2024
Infinix

INFINIX-LOGO

Infinix X6835B Hot 30 Play Smartphone

Infinix-X6835B-Hot-30-Play-Smartphone-PRODUCT

Product Information

  • Product Name: Infinix X6835B
  • Model: M

Explosion Diagram Specification:

  1. FL(CTP+LCM)
  2. PS RUBBER
  3. PCBA COPPER A
  4. PCBA MB
  5. F CAM FRAME
  6. FPC SIDE KEY
  7. REC
  8. FM
  9. R CAM CON FOAM 16M
  10. R CAM CON FABRIC 8W
  11. LCM CONN RUBBER
  12. MAIN WATERPROOF FRAME
  13. MI HOUSING
  14. NFC
  15. R FLASH DECO
  16. R CAM RUBBER 8W
  17. R FLASH LENS
  18. R CAM LENS 8W
  19. SCREW L2.0
  20. SPK
  21. PCBA SUB
  22. F HSG ASM
  23. PCBA COPPER C
  24. PCBA COPPER B
  25. PCBA GRAPHITE FILM
  26. F CAM
  27. F CAM COPPER
  28. REC COPPER
  29. CARDHOLDER
  30. R CAM 16M
  31. R CAM 8W
  32. BAT CONN RUBBER
  33. MAIN WATERPROOF MYLAR
  34. MI RAD GRA
  35. SCREW L3.5
  36. R CAM DECO 16M
  37. BAT COVER ASM
  38. R CAM LENS 16M
  39. R CAM DECO 8W
  40. SUB CONN RUBBER
  41. MOTOR LINEA
  42. USB RUBBER
  43. EARPHONE RUBBER
  44. COAXIAL CABLE
  45. BAT

Product Usage Instructions

Know your phone:

  1. Front Camera
  2. Volume + key
  3. Volume – key
  4. Power key & side fingerprint sensor
  5. NFC

SIM/SD card installation:

  1. Power off mobile.
  2. Refer to the user manual for SIM / SD card installation.

Charging the phone:
You can charge your device using a charger or by connecting it to the computer using a USB cable (which comes with the phone). Use only the INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution:
Labeling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Explosion diagram specification

Infinix-X6835B-Hot-30-Play-Smartphone-FIG- \(1\)

1 FL(CTP+LCM) 2 F HSG ASM
3 PS RUBBER 4 PCBA COPPER C
5 PCBA COPPER A 6 PCBA COPPER B
7 PCBA MB 8 PCBA GRAPHITE FILM
9 F CAM FRAME 10 F CAM
11 FPC SIDE KEY 12 F CAM COPPER
13 REC 14 REC COPPER
15 FM 16 CARD HOLDER
17 R CAM CON FOAM 16M 18 R CAM 16M
19 R CAM CON FABRIC 8W 20 R CAM 8W
21 LCM CONN RUBBER 22 BAT CONN RUBBER
23 MAIN WATERPROOF FRAME 24 MAIN WATERPROOF MYLAR
25 MI HOUSING 26 MI RAD GRA
27 NFC 28 SCREW L3.5
29 R FLASH DECO 30 R CAM DECO 16M
31 R CAM RUBBER 8W 32 BAT COVER ASM
33 R FLASH LENS 34 R CAM LENS 16M
35 R CAM LENS 8W 36 R CAM DECO 8W
37 SCREW L2.0 38 SUB CONN RUBBER
39 SPK 40 MOTOR LINEA
41 PCBA SUB 42 USB RUBBER
43 EARPHONE RUBBER 44 BAT
--- --- --- ---
45 COAXIAL CABLE  

Know your phone

Infinix-X6835B-Hot-30-Play-Smartphone-FIG- \(2\)

  1. Front camera
  2. Volume + key
  3. Volume – key
  4. Power key & side fingerprint sensor
  5. NFC

SIM/SD card installation

  1. Power off
  2. Refer to the following picture for SIM / SD card installationX6835B

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone). Use only INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty

FCC Caution

Labeling requirements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful
  • This device must accept any interference received, including interference that may cause undesired operation.

Information to user
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6835B (FCC ID:2AIZN- X6835B) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.20W/kg and when properly worn on the body is 0.67W/kg.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna

For DTS patents, see http://patents.dts.com Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

Operating System: AndroidTM Android is a trademark of Google LLC.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals