BROAN NuTone BKR60 Bath Fan Replacement Motor Kit Instruction Manual
- June 12, 2024
- Broan NuTone
Table of Contents
- BROAN NuTone BKR60 Bath Fan Replacement Motor Kit
- Product Information: BKR60 Bath Fan Replacement Motor, Wheel
- Product Usage Instructions
- BKR60 Bath Fan Replacement Motor, Wheel and Cover Kit
- PACKAGE CONTENTS
- TOOLS NEEDED (not included)
- Installation Instruction
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BROAN NuTone BKR60 Bath Fan Replacement Motor Kit
Product Information: BKR60 Bath Fan Replacement Motor, Wheel
and Cover Kit
The BKR60 Bath Fan Replacement Motor, Wheel and Cover Kit is a replacement kit for bath fans. It includes a fan cover grille, motor and wheel assembly, motor plate, and scroll band (for select fan models). The kit is designed to replace the existing components of a bath fan to ensure proper functioning.
For customer support and product registration, U.S. customers can visit
www.broan-nutone.com/en-us/home/customer-service/product-registration
or call Broan-NuTone Technical Support at
1-800-558-1711. Canadian customers can
visit
www.broan-nutone.com/en-ca/home/customer-service/product-registration
or call Broan-NuTone Technical Support at
1-800-567-3855.
Product Usage Instructions
- Switch off the power at the service panel and lock the service disconnecting means to prevent accidental power switching.
- Always wear safety gloves and glasses when working with the product.
- Remove the old fan cover by following the provided instructions.
- If applicable, bend the plastic scroll band into a crescent shape and place the ends of the scroll band behind the double tabs. Align the center slot of the scroll band on the single tab in the fan housing. Skip this step if your fan housing does not have double tabs.
- Snap the new motor and wheel assembly into the fan housing and plug in the motor. Insert the tabs on the motor plate into the slots on the fan housing. Pivot the assembly up and snap the third motor plate tab into the fan housing (motor plate A) or push up until touching the wiring box and secure with a screw (motor plate B).
- Ensure that the motor power cord is routed as shown to prevent electrical shock caused by wire damage. Attach the new cover by squeezing one spring and inserting it into the fan slot. Repeat with the other spring. Push the cover up against the ceiling or wall.
Note: The tools needed for installation, such as a screwdriver, are not included in the package.
BKR60 Bath Fan Replacement Motor, Wheel and Cover Kit
WARNING
Switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally.
CAUTION
Always wear safety gloves and glasses.
For U.S. customers, register your product at:
www.broan-nutone.com/en-us/home/customer-service/product-
registration
Broan-NuTone Technical Support (U.S.A.):
1-800-558-1711
For Canadian customers, register your product at:
www.broan-nutone.com/en-ca/home/customer-service/product-
registration
Broan-NuTone Technical Support (Canada): 1-800-567-3855
PACKAGE CONTENTS
TOOLS NEEDED (not included)
Tape Measure
Screwdriver
(for select fan models only)
Scan this QR code to access the
installation video.
Installation Instruction
Remove motor and wheel assembly from existing fan. Refer to installation video for ease of removing motor and wheel assembly.
- FAN HOUSING DIMENSIONS : 7½” x 7¼”
- DIMENSIONS : 7½ po x 7¼ po
- FAN HOUSING DIMENSIONS: 8″ x 7¼” OR 8 ¹/??” x 7 ³/?
Choose the motor plate according to housing dimensions. Compare to your existing motor plate to ensure the right fi t.
| Fan Housing dimensions (in) Dimensions du | Motor plate to use Plaque |
|---|---|
| 7 ½ x 7 ¼ | A |
| 8 x 7 ¼ | B |
| 8 ¹/ x 7 ³/ | B |
Motor plate
Motor plate
Attach the new motor plate to the new motor and wheel assembly. (Motor plate A shown, same procedure for motor plate B).
Place the new motor plate onto the motor, lining up the motor posts.
Securely fasten using the 2 nuts and wrench included.
WARNING
The motor power cord must be routed as shown to prevent electrical shock
caused by wire damage.
Skip this step if you have a 7 ½” x 7 ¼” fan housing -or- a 8” x 7 ¼” fan
housing with an existing metal scroll band.
This step is for select fan models only with a 8” x 7 ¼” fan housing that do
not have an existing metal scroll band.
Bend plastic scroll band (pictured in grey) into a crescent shape. Place ends
of scroll band behind the double tabs. Align the center slot of the scroll
band on the single tab in the fan housing. If your fan housing does not have
double tabs, skip this step.
Snap new motor and wheel assembly into the fan housing and plug in motor.
Insert 2 tabs on the motor plate into the 2 slots on the fan housing. Pivot
the assembly up and snap the third motor plate tab into the fan housing (motor
plate A) -or- push up until touching the wiring box, then secure with screw
(motor plate B).
Motor plate
Motor plate
Attach new cover by squeezing one spring and insert into fan slot. Repeat with the other spring. Push cover up against the ceiling or wall.
Broan-NuTone LLC, 926 West State Street, Hartford, Wisconsin, USA 53027 www .broan-nutone.com 800-558-1711 Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville. Québec, Canada J2C 7W9 www.broan- nutone.ca 800-567-3855
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>