MONOGRAM ZDOD240NSS Outdoor or Indoor Refrigerator

Product Information

The Design Guide Outdoor/Indoor Refrigerator is a high-quality refrigerator designed for both indoor and outdoor use. It is manufactured by Monogram, a trusted brand known for its reliable and innovative appliances. This refrigerator comes with a 3-prong (grounding) plug to ensure electrical safety. It requires a grounded 3-prong wall outlet with a voltage rating that matches the rating plate. The recommended electrical supply is 115 Volt AC, 60 Hz, with a 15- or 20-amp fuse to prevent overloading and fire hazards. For safety purposes, the power cord should not be cut or modified in any way. The refrigerator should always be plugged into its own individual electrical outlet to ensure proper performance.

Product Usage Instructions

1. Before starting the installation process, read the entire user manual carefully to ensure proper installation and usage of the refrigerator.
2. If you have received a damaged refrigerator, contact your dealer or builder immediately for assistance.
3. Ensure that flammable materials and vapors are kept away from the refrigerator to prevent fire or explosion hazards.
4. During the installation process, keep small parts away from children under 3 years of age to reduce the risk of choking.
5. Connect the refrigerator to a grounded 3-prong outlet. Do not remove the ground prong or use adapters or extension cords.
6. If installing the refrigerator in an outdoor location, it must be connected to a power source with Ground Fault Circuit Interrupt(GFCI) protection. Local codes may require a separate circuit. If unsure about the GFCI protection, consult a professional electrician for verification.
7. Ensure that the wall outlet and circuit are properly grounded. If encountering a 2-prong wall outlet, have it replaced with a grounded 3-prong outlet. Do not use adapters.
8. Always grip the plug firmly and pull it straight out from the outlet when unplugging the refrigerator. Do not pull on the power cord.
9. If the supply cord is damaged, discontinue use and have it replaced by a qualified service professional using an authorized service part from the manufacturer.
10. When moving the refrigerator, be careful not to roll over or damage the power cord.

For any further assistance or inquiries regarding Monogram products, visit monogram.com or call the customer service numbers provided in the user manual.

Safety Information

Before You Begin
Read these instructions completely and carefully.

• IMPORTANT:   Save these instructions for local inspector’s use. Observe all governing codes and ordinances.
• Note to Installer : Be sure to leave these instructions with the Consumer.
• Note to Consumer:   Keep these instructions with your Owner’s Manual for future reference. If you received a damaged refrigerator, you should immediately contact your dealer or builder.
• Skill Level:   Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information.
• Explosion Hazard: Keep flammable materials and vapors away from refrigerator. Failure to do so can result in fire, explosion, or death.

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product.

For Monogram local service in your area, call 800.444.1845 or visit monogram.com.
For Monogram service in Canada, call 888.880.3030
For Monogram Parts and Accessories, call 800.444.1845 or visit monogram.com.
For Monogram Parts and Accessories in Canada, call 888.880.3030 or visit monogram.ca.

Connecting Electricity

Electrical Shock Hazard.

• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.

THIS PRODUCT MUST BE CONNECTED TO A POWER SOURCE WITH GROUND FAULT CIRCUIT INTERRUPT (GFCI) PROTECTION WHEN INSTALLED IN AN OUTDOOR LOCATION. LOCAL CODES MAY REQUIRE A SEPARATE CIRCUIT. IF YOU ARE UNCERTAIN ABOUT THE GFCI PROTECTION ON THE POWER SOURCE TO WHICH YOU ARE CONNECTING THIS APPLIANCE, PLEASE CONTACT A PROFESSIONAL ELECTRICIAN FOR VERIFICATION.

Failure to follow these instructions can result in death, fire, or electrical shock.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
• Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Do not use an adapter.
• The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
• A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded electrical supply is required. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
• Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.
• Immediately discontinue use of a damaged supply cord. If the supply cord is damaged it must be replaced by a qualified service professional with an authorized service part from the manufacturer.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

Important Information

Key Ejecting Lock

( NOTE : Two keys are included.)
To prevent a child from being entrapped, keep the key out of reach of children and away from the appliance. .Keep the keys out of reach of children and away from the refrigerator in a safe and secure place. The key for the spring- loaded lock is automatically ejected. The key will not remain in the lock while the door is opened or closed.

NOTICE:  Before closing the door, make sure the lock pin does not protrude beyond the top of the door, to prevent potential damage to the cover or cabinetry.

Caring for Your Stainless Steel

• Before installation or first use, we strongly advise you polish the stainless steel exterior and handle with a stainless steel cleaner that is approved per the Outside Cleaning instructions of the Owner’s Manual. To preserve and protect the fine finish, we strongly advise that you apply stainless steel cleaner monthly.

• All stainless steel can be damaged by the following substances. Care must be taken not to allow these substances to come in contact with your Outdoor/ Indoor Refrigerator. If any of these do get on your unit, wash and clean the unit immediately (see the Care and Cleaning section in the Owner’s Manual).

• Battery Acid

• Pool Chemicals (such as Chlorine and Bromine)

• Lawn Fertilizer

• Ice Melting Salts

• Creosote

• Iodine

• Pickling Juice

• Urine

The following naturally occurring materials can cause damage to the stainless steel finish. If any of these substances do get on your unit, wash and clean the unit immediately (see the Care and Cleaning section in the Owner’s Manual).

• Bird Droppings
• Tree Sap
• Sea Water

Tools Required

• Heavy-duty work gloves

• 2 Phillips screwdriver (for built-in installations only)

• Adjustable wrench

Parts Supplied

• Two keys

Design Guide

The Installation Space

Choose the location:

• * This product has been designed as a free-standing unit; however, if desired, it may also be built-in.

  • These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door.

• Do not operate these products where the temperature will go below 45°F (7°C) or above 120°F (49°C).

• Unit must be installed on a structurally sound and level surface strong enough to support a fully loaded refrigerator, or approx. 250 lbs.

The cutout depth should be 24″
The cutout dimensions shown allow for a full door swing and access to the pull-out racks when installed in standard 24″ deep cabinets.

• The Outdoor/Indoor Refrigerator can be used freestanding.
• If installing between frameless cabinets, a 1/2″ wide filler strip or side panel may be required on the hinge side. The filler strip will act as a spacer between the case and adjacent cabinet door swing. The width of the opening must include the filler panels.

NOTE:  In a standard 24″ opening, the door will protrude 1-1/2″ forward of the surrounding cabinets.

Additional Specifications

A 120 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall as shown. Electrical must be located on rear wall as shown.

THIS PRODUCT MUST BE CONNECTED TO A POWER SOURCE WITH GROUND FAULT CIRCUIT INTERRUPTER (GFCI) PROTECTION WHEN INSTALLED IN AN OUTDOOR LOCATION. LOCAL CODES MAY REQUIRE A SEPARATE CIRCUIT.

 | Description| Outdoor

ZDOD240

Dimensions

---|---|---
A| Height (Level leg down) includes hinge| 34 3/16” (868.4 mm)
B| Width (Including door)| 23 5/8” (599 mm)
C| Width without door| 23 7/16” (596 mm)
D| Handle Depth Range unless Custom Handle| 2 1/8”, 2 5/8”

(54, 66.7 mm)

E| Depth including Door (& custom panels) without Handle| 23 3/4” (601.7 mm)
F| Depth without door| 21 13/16” (554.4 mm)
G| Toe Kick Height (floor to bottom of door)| 4″ (102 mm)
H| Level Leg Max Adjustment| 1″ (25 mm)
I| Decorative Toe Kick Part Dimension| 23-7/16″ W x 3-1/8” H (596 W x 79 H mm)
J| Single Standard Opening| 23 3/4″ (603 mm)
K| Single Flush Inset Opening| 25″ (635 mm)
L| Dual Standard Opening| Not Applicable
M| Dual Flush Inset Opening| Not Applicable
N| Maximum Cabinet Opening Height| 35″ (889 mm)
O| Minimum Cabinet Opening Height| 34.5″ (876 mm)
P| Standard Cabinet Opening Depth| 24″ (610 mm)
Q| Gap between drawers| Not Applicable
R| Depth with door open 90 or drawer fully open| 45 9/16″ (1157 mm)
S| Height with top cover (Level leg down)| 35 7/8″ (911.4 mm)

Design Guide

Product Clearances and Location Requirements
The Outdoor/Indoor Refrigerator is factory set for a 110° door swing.

When installed in a corner:

• Allow 5-1/4″ min. clearance on the hinge side for the 90° door swing and to allow racks to slide out.
• Allow 15″ minimum clearance on the hinge side for a full 110° door swing.
• Test the door swing. Carefully open and close the door. Adjust if the door makes contact with the cabinetry.

THE INSTALLATION SPACE
For a flush installation
The Flush cutout depth should be 25″ Install a 2 1/4″ wide filler strip on the hinge side. The filler strip will act as a spacer between the door case andadjacent cabinets and will act as a spacer between the door case and adjacent cabinets and will prevent inter- ference with the cabinet door swing. Recess the filler strip 1 5/8″ back from the front face of the refrigerator, or even with the front edge of the product case (behind the gasket). The width of the opening must be 25″ (including thw 1 1/4″ filler strip).

Preparation for Built-In Under-Counter Installations Only
The top canopy may be removed when installing under a countertop

• Remove the three screws from the back of the top canopy (A).

• Using heavy-duty work gloves, lift up on the top canopy back (B) and slide it forward until it unlatches from the unit (C).

• Lift the top canopy up and off of the unit.
  NOTE: Keep the top canopy and screws for future freestanding installations.
  NOTE: When installing the unit in a free-standing configuration, the top canopy must be left in place.

• If replacing the top canopy make sure the three latches in the front slide into the front lip of the canopy before pushing the canopy to the rear of the unit. Under side edges of the stainless steel canopy top may be sharp. Wear heavy-duty work gloves when moving the top.

CAUTION:  Under side edges of the stainless steel canopy top may be sharp. Wear heavy-duty work gloves when moving the top.

Installation Instructions

Step 1 Remove Packaging

• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape, and protective plastic coverings.

WARNING : Small objects are a choking hazard for children. Remove and discard any parts not used.

Step 2 Level

• Use an adjustable wrench to turn and raise or lower the leveling legs.
• Measure the floor-to-countertop height inside the opening. Adjust leveling legs until the product is approximately 1/8″ less than countertop height.

INSTALLATION TIP:
Measure floor to underside of the countertop inside the opening.

• If the room floor is higher than the floor inside the opening, adjust the rear leveling legs to approximately 1/8″ less than the opening height. Screw front leveling legs all the way in to shorten the height at the front. This will allow you to slightly tip the unit into the opening. Once the unit is in the correct position, the front legs can be adjusted to level the product.

Step 3 Connect Power

• If the refrigerator is used outdoors, plug the power cord into a GFCI receptacle.
• Check to make sure power is on by opening the door to see if interior light turns on.
• The interior fan runs at all times except when the door is open. See the the Owner’s Manual for further explanation.

Step 4 Slide Product into the Cutout

NOTICE:  Do not push against the door with your knees. Do not push or lift the unit by the door handle. Damage may occur!

• Open the door and gently push the unit back into the opening with your hands against the sides. Be careful not to entangle power cord.
• In a standard 24″ opening, the door will protrude 1-1/2″ forward of the surrounding cabinets.
• Check again to be sure the unit is level.
• If the unit is installed under a countertop, adjust the leveling legs until the unit is resting firmly against the bottom of the countertop.
• If alignment with adjacent cabinetry is an issue, use a shim to secure the unit against the underside of the countertop.
• Test the door swing. Carefully open and close the door. The door should not rub or catch on adjacent cabinetry. Notify the installer if the door makes contact with cabinetry.

Step 5 Set Temperature Controls

• The temperature controls are preset. Refer to the Owner’s Manual for more information. Allow 12–24 hours for temperature to stabilize.

NOTE : The Outdoor/Indoor Refrigerator operates very quietly. You may not notice the unit running, and when first installed, the fans and motor may not come on immediately—this is normal. If the display is lit and the light is working, the unit is operating.

Staining Wood Drawer Fronts

The drawer fronts are unfinished cherry wood. During use, oil from hands may accumulate and stain the wood.

• * The drawer fronts may be stained and sealed to match adjacent cabinetry.

  • Apply the stain and sealer according to the manufacturer’s instructions. To avoid unpleasant odor, keep the door open to ventilate and allow the stain/ sealer to dry completely before using the product.

NOTE: While performing installations described in this book, safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor at Monogram. Therefore, materials, appearance and specifications are subject to change without notice.

31-51542-7
01-20 GEA
Monogram.com
Printed in Serbia

References

• Monogram Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>