Rowenta RR7987 Robot Vacuum Cleaner User Guide
- June 12, 2024
- Rowenta
Table of Contents
Rowenta RR7987 Robot Vacuum Cleaner User Guide
Please read carefully the “Safety and use instructions” booklet before first use.
For more information.
Your robot may encounter some difficulties on carpets: with fringes, too thick, with long piles, too light (ex: bathroom carpet)
- Power / Start Pause
- LDS (Laser Distance Sensor)
- Recharge / Spot cleaning
- WIFI indicator LED
- Reset button
- Button for taking out dust box and water tank
- Dust box and water tank
- Air outlet
- Collision bumper
- Follow wall sensor
- Dust box and water tank
- Water outlet adapter
- Filter
- Dust bin opening button
- Water inlet
- Water inlet cap
- Buckle
- Dust box and water tank separation button
- Pleated filter
- Foam filter
- Pre-filter
- Anti-drop sensor
- Side brush
- Wheel
- Water outlet
- Charging electrode
- Caster
- Rolling brush
- Rolling brush cover
- Lock
- Water outlet
- Removal button
- Slot
- Washable mop
Remove the bottom cover and connect the docking station with the adapter, and pay attention to arranging adapter connection wires to avoid being wound during sweep. Put the bottom cover back.
To place the docking station, make sure there is an empty area of 0.5m on the side and 1.5m in front of the docking station. Do not install the docking station near stairs. The cable must be tight. Always place the docking station on hard floor. Do not place the docking station on carpet.
Connect the adapter to a wall socket. The docking station lights when the robot is not plugged in. Remove the protective strip on the bumper to ensure proper operation of the device.
Please fully charge the robot before using it for the first time. To do so, place the robot on the docking station and align it to the charging terminal. When the robot is correctly plugged, the docking station light will switch off. When the white indicators on the robot are normally set on, the robot is fully charged (4-5 hours).
In order to extend the battery lifespan, always keep the robot charging on the docking station while not using it.
When not using the vacuum cleaner for a long time, please fully charge the battery, switch off the robot and store the robot in a cool dry place.
When the white indicator is flashing slowly, the device is waiting for
connection.
When the white indicator is flashing rapidly, the device is connecting WIFI.
When the white indicator is normally set on, the device is connected !
Wipe robot sensors with a dry, soft cloth including:
- Wall sensor on the right side of the robot
- Four anti-drop sensors on the bottom of the robot
- Infrared anti-collision sensor in front of the robot on the bumper
Please also wipe charging electrodes and the window of the charging dock regularly
To clean the dust box and water tank, open the robot cover, press the release
button and remove the dust box and water tank.
Press the open button of the dust box and empty the dust box. Tap the dust box
to knock off excess dirt.
Take out the foam filter and pleated filter. Clean the filters with the
cleaning tool.
Users can also wash the filters for deep cleaning.
Press the release button of dust box to separate the dust box from the water
tank.
Flush the water tank, dust box and filter module thoroughly with water.
Let the water tank, dust box and filter module naturally dry for the next use.
Put the pre-filter, foam filter and pleated filter back, and put the filter
module back into the dust box.
Reinstall the water tank and dust box, and then install the module back to the
machine.
To clean the central brush, turn the robot OFF and turn the robot upside down. Press down the locker to take out the protective cover. And take out the central brush upwards. Clean the central brush with the cleaning tool.
To replace the central brush after having cleaned it, put one end of the central brush into the corresponding hole first. Then press the brush cover and fix it with the locker
To clean side brush, remove it by unscrewing it and use a cleaning brush to clean the side brush and the entanglements in the slot of the side brush. Clean side brushes once a month.
Replace side brushes every 6 months. Throw away the old brushes and replace them with new ones. Screw the new brushes on the robot.
To clean the wheels, clean the front, left and right wheels once a month. The wheel shaft may be entangled by hair, cloth strips, etc. so please clean it in time !
Every 6 months replace the pleated filter and the foam with new ones to maintain optimal performances.
Do not throw the robot in the bin. Always wear gloves and protection. Remove the 5 screws. Remove the bottom cover. Take off the battery. Unplug the battery connector.
The languages NL, PT, RO, BG, CS, SK, UK, EL, SR, HR, HU and SL are included in the safety instructions.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>