NATUREL ZIL80LEDC 80cm Mirror Instruction Manual
- June 12, 2024
- Naturel
Table of Contents
NATUREL ZIL80LEDC 80cm Mirror
Dimension
General Information, Purpose of Use
Before the first use, the consumer is obliged to read the instructions to ensure secure and problem-free use of the product. It is a stationary LED light determined to illuminate inner spaces like for example bathrooms, hallways, etc. The light is constructed as a mirror with a light source located behind the mirror. The mirror can be used as a decorative lighting. Some models with larger amount of individual LED diodes provide sufficient lighting and they can be used for illuminating the room. LED mirrors are illuminated by high-performance LED strips characterized by low energy consumption and clear luminosity. Lifespan of LED diodes is up to 50.000 hours.
Safety Instructions
For any kind of handling, maintenance or assembly it is necessary to follow
basic safety requirements resulting from the specific activity.
Please follow the next safety instructions in this manual.
Instructions marked by this sign are determined to prevent any risk or injury
by general danger.
Instructions marked by this sign are determined to prevent any risk or injury
by electric current.
Connecting to electricity network requires qualified electrician.
Requirements for connecting the bathroom mirror:
– The mirror shall be located according to valid security regulations.
– The mirror shall be connected to the mains in the network 1NPE 230V 50Hz
TN-S.
– Front fuse max: 10A and residual-current device (RCD) 30mA
Handling
The light is packed in cardboard and covered by wrap and protected by polystyrene layer and MDF desk. Due to its weight and large sizes, handling with the light should be done carefully. The light is equipped with mirror which is very fragile and easily breakable. In case of handling with angular mirrors, let the protective plastic edges remain attached to the mirror and take them off after the installation is done.
Installation
The light is determined to be attached to wall or another suitable inner
surface.
The light can be installed in the area around the basin or around the shower
or bath but it cannot be placed in zones 0+1+2 (see the pictures in the
paragraph Instructions for Assembly – installation on wall). Connecting to
electricity network requires a qualified electrician and must be done
according to the regulation 50 Sb/78. Connect the supply cable (at the back
side of the mirror) to the existing mains in the wiring box placed preferably
behind the mirror. If there is already a supply cable in the wall, it is
possible to connect it with the mirror cable on the back side of the mirror by
the terminal box (article number ZP 01 – not included in the package). It is
highly recommended that the installation is accomplished by two persons.
Maintenance
The mirror is basically maintenance-free. Outer side of the mirror requires
washing by classic detergents for washing windows. Do not use any aggressive
detergent (especially those containing chlorine and its derivatives) which can
cause oxidation of the mirror. Inner side of the mirror does not require any
specific maintenance. In case of damaging the protective cover, it is
necessary to have it replaced in producer’s service centre.
Warning! Turn the mirror off and turn off the electricity supply mains before
operating the mirror. Electric equipment of the mirror is maintenance-free,
only in case of light source failure it is necessary to replace it. Contact
the producer or seller for any repairs. Installation of electrical device
requires qualified electrician and it should be done in accordance with
regulations. If the supply cable is damaged, it must be replaced by the new
cable provided by the producer or their service technician.
Warranty Period
There is a warranty period in accordance with the Civil Code. The producer provides the warranty period of 24 months beginning from the date of purchase. Any other handling with the product than this recommended in the manual is forbidden.
Technical Specification
Power supply 230 V AC 50 Hz, L+N+PE
Front fuse 10 A max RCD (Fi) 30 mA.
Input 5-50 Watt
Appliance class I.
Weight Max 20 kg
Light source LED strip, cool white / warm white
Light source life up to 50 thousand hours.
Ballast 1 – 2 x ballast for 12 V DC SELF
IP Code IP 44
The mirror consists of aluminium frame comprising various profiles according
to the type, of a size 20-50 x 20-50 mm. Mirror of various shapes and sizes
(width and height: 400 – 1500 mm, thickness of glass: 5 mm) is stuck on the
frame. There is an access to the power supply from the back side of the mirror
through the metal cover with stainless steel screws. Variants of the product
are based on size, shape of the mirror (rectangular, square, oval, round with
sharp edges, round edges, etc.), aluminium frame and different LED lighting
(warm white / cool white). Electric connection remains the same. The LED
strips are glued to the luminaire with a thermally conductive adhesive. It is
not necessary to change the light source, due to its long life. For inspection
purposes or at the end of the LED luminaire‘s lifetime, the light source can
be disconnected by removing the metal cover and then detached from the light
source holder. End users cannot change the light sources due to permanent
damage to the product.
Light source in this type of mirror is irreplaceable, after the lifespan is
over, the whole mirror needs to be exchanged.
Electric Diagram
Products of article numbers: ZIL80LEDC
Products of article numbers: ZIL80LEDSEC (with a switch for on/off and
changing the colours warm/cool white):
Instructions For Assembly
The light is determined to be attached to wall or another suitable inner
surface.
The light can be installed in the area around the basin or around the shower
or bath but it cannot be placed in zones 0+1+2 (see the pictures in the
paragraph Instructions for Assembly – installation on wall). Connecting to
electricity network requires a qualified electrician and must be done
according to the regulation 50 Sb/78. Connect the supply cable (at the back
side of the mirror) to the existing mains in the wiring box placed preferably
behind the mirror. If there is already a supply cable in the wall, it is
possible to connect it with the mirror cable on the back side of the mirror by
the terminal box (article number ZP 01 – not included in the package). It is
highly recommended that the installation is accomplished by two persons.
For the assembly use a pair of wall plugs and screws which are included in the
package. These are determined for brickwork with a standard plaster thickness.
For other types of wall use appropriate attachment components.
Follow the instructions for assembly.
Do not install in the zones 0+1+2
-
Firstly, prepare the final position of the mirror. The optimal way for choosing the right position is to place the mirror on the required place on the wall and see if that suits you.
-
With help of the other person mark the upper edge of aluminium frame on the wall. Do not mark the edge of the mirror! (Aluminium frame of some mirror models is of a different size than glass of the mirror!). Draw a small horizontal line. See the picture below.
-
60 mm under the line draw another line and using the water-level draw this line in a size of the mirror width. Doing this you measured the height of the holes for screws (their horizontal position).
Mark the centre which you can measure by the sink or tap. -
Now it is important to know the screw pitch, their vertical position. (NIMCO offers a wide range of models and types of mirrors of different size.
This general manual does not indicate the pitch for each model. It is then important to measure it.) The pitch is measured directly on the mirror. On the back side of the mirror there are holes in the aluminium frame for vertical or horizontal attachment. (Warning! It is possible to attach the mirror horizontally or vertically.). Choose the correct holes according to your choice. These are the round holes. Measure their pitch, the distance of their centre lines (x).
See the picture below
-
You measured the pitch of the holes for screws. Now you mark them as the intersection points on the horizontal line on the wall that you already drew. Every intersection point is ½ of the measured pitch distant from the marked centre (½ X). Check one more time if the total distance between intersection points on the wall (Y) corresponds with pitch of the holes on the mirror (X).
-
Drill the holes to the marked intersection points. Use the correct drill and attachment components according to the type of wall material! If the base is suitable (it is the standard brick wall with standard plaster thickness) you can use wall plugs and screws included in the package.
Put the wall plugs in the drilled holes and use the screws whereas their head and shank stick out (max 5 mm of the visible shank).
-
Connect the connecting cable with the mains cable or junction box. It is recommended to work in a pair! For connecting the cables, you can use the terminal box of article number ZP01 (in the picture) or any other terminal box with the suitable IP for bathroom furnishing. Before you start connecting the cables, make sure there is no electric power in the supply cable! Connect the cable of the mirror to the electric power supply to conductors L, N and PE. Terminal box is not included in the package. Use only recommended supply voltage 230 V AC, 50 Hz, L+N+PE with front fuse max. 16 A.
-
Now you can hang the mirror. The holes in the frame of the mirror goes on the screws and hang the mirror slowly few millimetres down. The mirror is now installed!
For the models marked ZIL80LEDC
The mirror is not equipped with any control. It is turned on/off through the
switch of the light located in the house. Two-button switch is recommended for
individual choice of lighting in the bathroom.
For models marked ZIL80LEDSEC
The mirror is equipped with a control – touch switch. It is turned on/off by
touching the centre of the sensor. It is possible to set the color of lighting
with these models (color temperature or chromaticity) by holding your finger
on the sensor. Color temperature ranges from 2700K (warm white) to 6000K (cool
white) or the other way around. Color temperature is automatically saved to
the memory. When turning on the mirror next time, the saved color temperature
will be used.
EU Certificate Of Conformity
Certificate of conformity is issued for this product according to the
authorized regulations.
The content of the issued ES certificate of conformity
Description of the product: Bathroom light with illuminated mirror
Name of the product: LED cosmetic mirror for bathrooms
Models of the product: ZIL80LEDC / ZIL80LEDSEC
The product is in accordance with the following regulations:
– Government Regulation no. 117/2016 Sb. on electromagnetic compatibility of
the product while being supplied to market
– Government Regulation no. 118/2016 Sb. on conformity of electric devices
determined for the use within the voltage while being supplied to market
and harmonized regulations:
ČSN EN 60598-1-ed.6 (360600) Lights – Part 1: General requirements and tests.
ČSN EN 60598-1-ed.6:2015/Revision1 (360600) Lights – Part 1: General
requirements and tests.
ČSN EN 60598-2-1 (360600) Lights – Part 2: Special requirements – Section 1:
Stationary lights.
Last two digits of the year when the CE mark was placed on the product: 17
The product is marked by
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>