ZPROV8040LED Mirror With Heated Film And Naturel Project Sensor Instruction Manual

ZPROV8040LED Mirror With Heated Film And Naturel Project Sensor

Product Information

Installation Manual: EN, DE, FR, IT

Dimensions:

• Width: 800mm
• Height: 780mm
• Depth: 400mm

Weight: 93mm

Technical Specifications:

• Power Supply: 230V
• Input: N/A
• Electrical Class: N/A
• Light Source: LED
• Light Source Service Life: N/A
• Ballast Protection: N/A

The light source of this luminaire is non-replaceable, the whole luminaire must be replaced at the end of its service life!

Product Usage Instructions

Safety Instructions

• Any handling, maintenance or installation must comply with the basic safety requirements imposed by the activity.
• Follow any other safety instructions in the installation manual.
• The instructions marked as “primarily to prevent general danger or personal injury” should be followed.
• The instructions marked as “primarily to prevent electric danger or personal injury from electrical hazards” should be followed.
• Connection to the mains must only be carried out by a person with an electrical qualification.
• Bathroom mirror connection conditions:
  • The mirror must be installed in accordance with the applicable safety regulations.
  • The product may be connected to a fixed supply in a 1NPE 230V 50Hz TN-S network.
  • Pre-wired protection max: 10A and current protector RCD 30 mA.

Handling

The luminaire is supplied packed in a carton and covered with foil protected by polystyrene lining. Due to its extra weight and large size, please handle the luminaire very carefully. The luminaire is equipped with a mirror which is very fragile and can easily break. For square mirrors, leave the plastic protective corner covers on during handling and remove them after installation.

Maintenance

Warranty Period: The product is covered by warranty within the meaning of the Civil Code. The manufacturer provides a warranty of 24 months from the product purchase. Any handling and operations other than those recommended in this manual are prohibited.

Use

The sensor has memory. When the mirror is switched off and then switched on, the last set color and light intensity is used.

Light Color Options:

• Warm Light: 3000 K
• Day Light: 4000 K
• Cold Light: 6000 K

Note: The intensity of the light can be adjusted within 0.5 seconds.

Installation

1. First, prepare the mirror location. The easiest way to select the correct position of the mirror is to directly place the mirror in the desired location on the wall and check if the position suits you.
2. Install the mirror outside the 0+1+2 zone.
3. Zone Bathtub side view: 225 cm

DIMENSION

General Information, Purpose of Use

Before first use, the user is required to properly consult this Installation Manual to ensure safe and trouble-free use of the product. This is a statio- nary LED luminaire designed to illuminate indoor areas such as bathrooms, corridors, etc. The luminaire is designed as a mirror with the light source located behind the mirror. The mirror is thus particularly suitable for use as decorative lighting. LED mirrors are mirrors illuminated by powerful LED strips with low power consumption and bright luminosity. The lifetime of the LEDs is up to 50,000 hours.

Safety Instructions

Any handling, maintenance or installation must comply with the basic safety requirements imposed by the activity.
Follow any other safety instructions in this manual.

• The instructions so marked are primarily to prevent general danger or personal injury.
• The instructions so marked are primarily to Electric danger or personal injury from electrical hazards.
• Connection to the mains must only be carried out by a person with an electrical qualification.
• Bathroom mirror connection conditions:
  • The mirror must be installed in accordance with the applicable safety regulations.
  • The product may be connected to a fixed supply in a 1NPE 230V 50Hz TN-S network.
  • Pre-wired protection max: 10A and current protector RCD 30 mA.

Handling

The luminaire is supplied packed in a carton and covered with foil protected by polystyrene lining. Due to its extra weight and large size, please handle the luminaire very carefully. The luminaire is equipped with a mirror which is very fragile and can easily break. For square mirrors, leave the plastic protective corner covers on during handling and remove them after installation.

Installation

The luminaire is intended primarily for mounting on a wall or other surface designed for indoor use.
The luminaire can be installed in the washbasin area and in areas with a bathtub or shower outside the 0+1+2 zone (see pictures in the Assembly Instructions). The electrical installation must be carried out by a person with an electrical qualification. The connection is carried out by: a) moving supply b) connecting the supply cable (at the back of the mirror) to the existing wiring in the wiring box preferably located behind the mirror. If there is already a connection cable on the wall, it can be connected via the terminal box to the connection cable on the back of the mirror.

Maintenance

Warranty Period

The product is covered by warranty within the meaning of the Civil Code. The manufacturer provides warranty of 24 months from the product pur-chase. Any handling and operations other than those recommended in this manual are prohibited.

Technical Specifications

• Power supply 230 V AC 50 Hz, L+N
• Pre-wired protection 10 A max RCD (Fi) 30 mA.
• Input 5-50 Watt
• Electrical class I.
• Light source LED strip, warm light / daylight / cold light
• Light source service life up to 50 k hours
• Ballast 1–2 x electronic ballast for 12 V DC SELF
• Protection IP 44

The light source of this luminaire is non-replaceable, the whole luminaire must be replaced at the end of its service life!

Electric Diagram

Products: ZPROV8040LED

Assembly Instructions

The luminaire can be installed in the washbasin area and in areas with a bathtub or shower outside the 0+1+2 zone (see pictures in the Assembly Instructions). The electrical installation must be carried out by a person with an electrical qualification. The connection is carried out by: a) moving supply b) connecting the supply cable (at the back of the mirror) to the existing wiring in the wiring box preferably located behind the mirror. If there is already a connection cable on the wall, it can be connected via the terminal box to the connection cable on the back of the mirror.

For assembly use a dowel and a screw (not included).

First, prepare the mirror location. The easiest way to select the correct position of the mirror is to directly place the mirror in the desired location on the wall and check if the position suits you.

Connect the mirror‘s connecting cable to the socket or cut the plug and connect the mirror‘s connecting cable to the mains cable or electrical box. You can use a connection terminal block with IP protection for bathroom equipment to connect the cables. Make sure there is no electricity in the supply cable before starting the connection!!! Connect the power cable of the luminaire to the power supply on conductors L and N. The terminal block is not included in the product. Use only the recommended supply voltage 230 V AC, 50 Hz, L and N with pre-set fuse of max. 16 A.

Use

The sensor has memory. When the mirror is switched off and then switched on, the last set colour and light intensity is used.

EU Declaration of Conformity

The product is covered by a declaration of conformity according to the relevant applicable regulations.
Product description: Bathroom luminaire with illuminated mirror surface

Name: LED bathroom mirror
Model: ZPROV8040LED

The product complies with the requirements of these regulations:

Government Decree No. 117/2016 Coll., on conformity assessment of products in terms of electromagnetic compatibility in delivering them to the market
Government Decree No. 118/2016 Coll., on conformity assessment of electrical equipment designed for use within certain voltage limits in delivering them to the market and harmonised standards:

ČSN EN 60598-1-ed.6 (360600) Luminaires – Part 1: General Requirements and Tests.
ČSN EN 60598-1-ed.6:2015/Oprava1 (360600) Luminaires – Part 1: General Requirements and Tests.
ČSN EN 60598-2- 1 (360600) Luminaires – Part 2: Special Requirements – Section 1: Stationary Luminaires.
The last two digits of the year in which the CE marking was affixed: 20
The device bears the mark of conformity:

SIKO KOUPELNY a.s.
Skorkovská 1310, 198 00 Praha 9
IČ: 26065801
CZECH REPUBLIC

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>