McALPINE SCA-RE Scale Defender Starter Kit Instruction Manual

McALPINE SCA-RE Scale Defender Starter Kit Instruction Manual

Warranty

In the unlikely event that you should experience any defect in the materials or workmanship of this product within ONE ‘year of purchase, the purchaser’s sole remedy shall be the replacement {at the manufacturers discretion) of all or any part of the product that is defective. All working parts, O-rings and valves are guaranteed for a period of ONE year from purchase provided that our advice concerning care has been observed. This is provided that the product has been used for normal domestic purposes in the UK and that the care, Installation and maintenance instructions have been observed. ‘The warranty extends to the original purchaser only. You should retain copy of your dated involve as proof of purchase to validate any claims under this guarantee.

Free lifetime guarantee registration: www.mialpineplumbing.com/sdregistration

Guarantee coves free replacement of ilk parts {excluding cartridges}

Replacing the dosing cartridges

‘The dosing filter capacity is a maximum of 40,000 liters an should be replaced when exhausted to maintain the effectiveness of protection. Inside the dosing filter 15 a small red ball, When the ball I at the bottom of the dosing falter . the filter should be replaced. We recommend checking the filter every month o so.

The pre-filter can be checked and leaned periodically, or upon changing the dosing cartridge to ensure the flow rate through the system Is opt reduced. This may vary depending upon your water conditions.

Replacing the dosing filter (H)

1. Tithe malls stopcock off before the Scale Defender, and tum off the the Full Bore solation/lever valve after the Scale Defender (I installed). Open taper drain off at the tows polar of the bulk ding and drain as much cold water as possible.

2. Place container underneath the filter housing (F), An screw the filter housing () clockwise (image 74) and welt for the residual water to drain away.

3. Unscrew the filter housing completely and pulp it down from the grey filter head (L)

4. Remove the used dosing cartridge (H) and clean the inside of the yellow housing required. 4 5. Place the new dosing cartridge inside the yellow housing {L}

5. Chacko the refilter mesh (G} Clean it first when dirty. ringed.

6. Screw the filter housing (L) tightly (by hand) back Into the grey dosing filter head (Sea towage T0) use some: WRAS Approved Water Potable lubricant if required.

7. Slowly open the stopcocks (with allocher taps in the house switched off) and check all eonnactians carefully for leaks around the installation. If possible, return to the installation after a longer period to double check for slower least,

8. Flush the filter system though now by opening tap in the dwelling.

Waking although this is 2 safe product tousle, some powder way get onto your hands if the dosing fitter {H) breaks. Always wash your hands with asap and ‘water. Should the dosing powder Eatonton your eyes rinse with wallet. If the nitration persists, please consult your Gf: f you accidentally ingest the dosing ponder through your mouth,

Troubleshooting Potential Reasons

‘The wades flow is reduced:

• The pre-filer mesh might need leaning, this s needs dining regular intervals depending on the quantity of particles in the water.

I cannot notice the effects of the system:

• If the filter system is new you should expect it totaled a few days to work fully.
• The dosing cartridge is empty (check the red ball indicator) and should be replaced.
• The dosing system is faulty unlikely) causing the Incorrect low dosage to be applied, the dosing filter should be replaced,

Debris is coming from the water supply:

• The pre-liter mesh s damaged allowing debris to enter and should be replaced.
• The size of the debris is smaller than the pre-fitter aging (but not harmful for your system).
• The dosing fitter is dislodging existing built up corrosion from the water system. This will reduce and then passim fewer sky.

Important Technical Data

• Minimum operating pressure : a3bar
• Minimum water temperature: 1c 100% safe for drinking water under BSEN 2212 and NEN-EN 1212 regulations
• Maximum operating pressure : 100 b23
• Maximum water temp. (feed): 40 C

If these temperatures or pressures are exceeded, even for short periods, damage can retool, I these instances pressure reducing valve should be installed before he system. Do no? instils the system in d vocation where it facer.

This product is approved and manufactured In accordance ‘with recognized European Standards, all materials used comply with the international standards for drinking wastes {British Standard BS EN1212 and European NEN-EN 1212). Please ensure that your system is kitted in accordance with Local Water Byelaws. The dosing system head contains non return valve to prevent back foil into the cold supply. ‘The system should only be fitted to 8 microbiologically Sofie water source.

These installation guidelines have been prepared for your direction and you must exercise due care at afl times. We do not accept responsibility fotproblems that may occur through improper installation. Whilst assembling the filter system take care not to accidentally loosen any factory fixed assemblies.

Installation Preparation

Scale Defender should only be installed by a competent person, and In accordance with these installation Instructions. All parts should be removed from their packaging and inspected for completeness and transport damage prior to Installation. If you have not installed this product you should read through these instructions before commenting.

The system should be Installed directly after the existing cold water stopcock. We strongly recommend installing a Full Bore isolation or Lever valve immediately after the system inane accessible position to alto maintenance and easy replacement of cartridges. Ensure the Incoming main is isolated prior to installation, care should be taken to drain 8 much residual water before commencing with install

Before installing the system t s essential that you thoroughly flush through the supply pipes in order to remade any remaining solder, swarf or impurities from your system. Failure to carry but this simple procedure could cause problems or damage to the workings of the system and invalidate the warrantee.

You should ensure that this product will both fit into the depth and area of the mounting position available and will reach the required inlet and outlet positions before installation. You should allow at least 50 mm of space below the system 1o allow this to be changed easily. Loosely position the system to check f any alteration to the existing pipework required, if this is the case do this now.,

The system must be mounted vertically a3 Shawn Installation layout example.

Installation

1. Create break in the cold water pipe afar the stopcock, the length of this break will change according to the layout of the installation you have chosen. Ensue the end section of the pipes are clean and free from burs. We suggest you place 2 bucket or similar under the break 10 catch any residuals walker in the system that coiid not be previously drained.
2. Screwabrass connector (D)o the Inlet f the system head (R ensuring t use the seal ) to make » watertight seal, please take care to note the flow direction on the head (F.8. 5crewa brass connector (D) to the outlet of the head {F) ensuring 10 use the seal (£} to make a watertight seal. Please take care to note the flow direction on the dosing head (F).
3. Place the dosing cartridge (H)into the housing (). now screw a housing () Into head (F} Nb. may be factory assembled.
4. Push the O-Ring {G) an top of the housing (L) and put the O-Ring (G) on Lop of the housing (th now screw 2 housing (Winton the head (F. Nb. Parts from 485 may be factory assembled.
5. IF connecting to 22 mm pipe: place the compression ‘nuts {8) then olives (C) over the pipe. Insert the pipe into the beads connecter (O now whitest holding connector {0 tighten compression nut {B) n this instance part (A}is not used.
6. If connecting to 2 1Smm pipe: place the compression nuts {8) then 22 x 15 reducers {A} aver the 15mm pipe. laser the pipe into the brass connector (D) now whilst holding connector (D) tighten compression nut {B. In this instance part (<) not used. Note the 22 % 15mm olive / reducers (Wail separate ion two when tightened to make a ‘watertight seal but can only be used office at which point the angled face of (9 & A will mate.
7. Once you have visually checked the installation of the Riel system and all connections, slowly open the stopcock {with all other taps in the house switched off) and check al) connections carefully for leaks around the installation. possible, fretum to the installation after a longer period to double check for slower leaks. Ensure the area 2round the ‘system is left accessible in order that the cartridge can be. changed periodically.

Themes may be 90 degree cornices tar version for small spokes. Farts must be provided by the installer.

How the system works
The Scale Defender water system is designed to reduce the damage that sediment can Couse 10 household taps and appliances. This level of dosage complies with the British Standard B5 EN 2212 and EC drinking water standard {NENEN 1212). The dosing cartridge adds food grade sodium phosphate to theincaming water supply at a maximum concentration of § parts per million, these additives coat the scale within the wastes making it more difficult for the scale to attach itself Lo surfaces.

Wins the scale is not physically comoved, this gives the water working properties similar to that of softens water improving. the effectiveness of detergents and preventing scale baited up. treading to improvements in heating system efficiency.

Other benefits include reduction of scale effects on showerheads, glasses, sanitary fitting’s and hosting elements in washing machines and boilers.

Scale Defender does not affect your natural ingestion of calcium via your water supply.

‘The installation should be periodically checked for damage. the property is left unattended for a prolonged period, we recommend isolating the water supply. When returning, Seale Defender shouted be flushed through s recommended by your water supplier.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>