perle CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter Module User Manual

: June 12, 2024
: perle

Table of Contents

perle CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter
Product Information
Product Usage Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

perle CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter

Module

Product Information

The CM-100MM Managed Fast Ethernet is a feature-rich fiber-to-fiber media converter module designed by Perle. It enables transparent fiber extension of 100Base-FX multimode fiber to 100Base-FX multimode or 100Base-LX/EX/ZX/BX single-mode fiber. The module can be installed in a high-density Perle Media Converter Chassis.

Perle’s advanced features ensure end-to-end fiber link transparency, allowing for efficient troubleshooting and reduced on-site maintenance. The module can be configured and monitored using a Media Converter Management Module in the chassis. It comes with a lifetime warranty and free worldwide technical support. For medium to large-scale deployment of media converters, Perle recommends using the PerleVIEW Device Management software, a multi-user, Windows server-based application that simplifies configuration, administration, monitoring, and troubleshooting. Perle offers an extensive range of CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter Modules to meet various fiber conversion requirements, whether it’s extending multimode to multimode or multimode to single mode.

Product Usage Instructions

Configuration Mode selection: Select whether the module should use the onboard DIP switches or enable the management module in the chassis to manage.
Module Information: View information such as chassis slot number, media converter model and serial, user-configurable module name, user-configurable fiber port name, hardware revision number, and firmware version number.
Module DIP switch settings: View hardware DIP switch settings.
Port Control: Enable or disable individual fiber ports on the module.
Fiber Port Status: View the status of fiber ports, including port enabled (Yes/No), connector type (SC, LC, ST), link status (Up/Down), far-end fault (OK, Failed), and fiber loopback mode (On/Off).
Module Control: Perform actions such as resetting the card to factory default, executing PHY-specific commands (write/read config, read DIP switches), updating firmware, and enabling/disabling fiber loopback mode.
Backup and Restore: Easily replace modules by saving a copy of the media converter configuration and automatically restoring it to the new module when detected in the slot.
Link PassThrough: Enable or disable Link\ PassThrough, which reflects the state of the receiver on one 100Base-X interface to the other 100Base-X fiber transmitter. This\ minimizes data loss during faults and aids in troubleshooting.
Far-End Fault (FEF): Indicates the presence of faults on the 100Base-FX fiber interface and facilitates troubleshooting.

100Base-FX to 100Base-X Fiber Mode Conversion

100Base-FX to 100Base-X Fiber to Fiber MediaConverter Module
Multimode to multimode or multimode to single mode
Extend multimode fiber to 120km ( or more through chaining )
Choice in SC, LC and ST fiber connector models
Signal regeneration prevents signal degradation
Advanced Features:
Link Pass-Through
, Far-EndFault, loopback for each fiber connection
High-density applications with Perle Media Converter
Chassis
Manage via SNMP, CLI – Telnet/SSH, Internet browser, or
PerleVIEW Centralized Management Package with an
MCR-MGT Media Converter Management Module

Installed in a high density Perle Media Converter Chassis , Perle’s feature- rich CM-100MM Fast EthernetFiber to Fiber Managed Media Converter Module enables transparent fiber extension of 100Base-FXmultimode fiber to 100Base-FX multimode or 100Base-LX/EX/ZX/BX single mode fiber.
Perle’s advanced features make the end-to-end fiber link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. When used with a Media Converter ManagementModule in the chassis, configuration and monitoring of the fiber ports can be performed. In addition, a lifetime warranty and free worldwide technical support make Perle’s CM-100MM Fast Ethernet Fiber toFiber Managed Media Converter Modules the smart choice for IT professionals.

For those environments requiring a medium to large-scale deployment of media converters, a centralized platform that simplifies the configuration, administration, monitoring, and troubleshooting of this gear is recommended. PerleVIEW Device Management software is a multi-user, Windows server-based application that delivers this level of Enterprise-grade solution.

Whether you need to extend multimode to multimode or multimode to single mode, Perle has an extensive range of CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter Modules to meet your fiber conversion requirement.

CM-100MM Fiber to Fiber Features: 100Base-FX to 100Base-X

Configuration Mode selection
Select whether the module is to use the on-board DIP switches or enable the management module in the chassis to manage

Module Information
- Chassis Slot number that the module is in
- Media converter model and serial
- User configurable module name
- User-configurable fiber port name
- Hardware revision number
- Firmware version number
Module DIP switch settings
- View hardware DIP switch settings
Port Control
- Enable or disable individual fiber ports on the module
Fiber Port Status
- Port Enabled (Yes/No)
- Connector type (SC, LC, ST)
- Link Status (Up/Down)
- Far End Fault (OK, Failed)
- Fiber Loopback mode (On/Off)
Module Control
- Reset card
- Reset to factory default
- Phy-specific commands such write/read config, read dip switches
- Update firmware
- Fiber Loopback mode. (On/Off)
- Upload/download configuration.
Backup and Restore
- Provides fast and easy module replacement. The management module will always save acopy of the media converter configuration and will restore this configuration automatically to the media module when it is detected in the slot.
Link Pass-Through
- When enabled, the state of the receiver on one 100Base-X interface is reflected on the other 100Base-X fiber transmitter.
- If disabled, the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.
- Using Link Pass-Through with Far-End Fault minimizes data loss when a fault occurs.If a fault occurs, the end devices have the indication of a failure available to make troubleshooting easier.
Far-End Fault (FEF)
- When enabled, the media converter transmits the Far-End Fault Indication over thefiber connection whenever a receive failure is detected. The media converter continuously monitors the fiber connection and clears the Far-End Fault Indication-condition when a valid signal is received.
- When disabled, Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-X fiber connection.
- The action the media converter takes on receiving a Far-End Fault Indication is dependent on the Link Pass Through switch setting.
Pause (IEEE802.3xy)
- Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter is transparent to Pause frames.
Signal Regeneration
- Signal Regeneration maintains signal integrity and allows for maximum fiber-to-fiber connections without degradation.
Cascading3
- Media Converters can be cascaded. Two or more Media Converters can be chained ina link to achieve even greater distances.
VLAN
- The Media Converter is transparent to VLAN-tagged packets.
Remote Loopback
- The Media Converter can perform a loopback on each 100Base-X fiber interface.

Indicators

Power / TST
- This green LED is turned on when power is applied to the media converter. Otherwise, it is off. The LED will blink slowly when in Loopback test mode.
Fiber link 1 /Receive activity (LK1)
- This green LED is operational only when power is applied. The LED is on when the100Base-X link is on and flashes with a 50% duty cycle when data is received.
Fiber link 2 on/ Receive activity (LK2)
- This green LED is operational only when power is applied. The LED is on when the100Base-X link is on and flashes with a 50% duty cycle when data is received.
Switches: On-Board (If Auto/Switch strap is set to Switch)
Link Pass Through
- Enabled (Default) – When the state of the receiver is changed on one of the 100Base-X interfaces it is reflected on the other 100Base-X fiber transmitter.
  When a Far-End Fault Indication is received on the fiber interface the 100Base-TXtransmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on.
- If disabled, the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface.
Far-End Fault (FEF)
- Enabled (Default)\ – The media converter transmits the Far-End Fault Indication over the fiber connection whenever a receive failure is detected. The media converter continuously monitors the fiber connection and clears the Far-End Fault Indication-condition when a valid signal is received.
- When Disabled, Far-End Fault Indications are not transmitted regardless of the condition of the received signal on the 100Base-X fiber connection.
Remote Loopback #1
- The media converter can perform a loopback on the link #1 fiber interface. Disabled (Default – Up)
- Enabled – The 100Base-X receiver is looped to the 100Base-X transmitter. Link #2’sfiber transmitter is taken off the interface.
Remote Loopback #2
- The media converter can perform a loopback on the link #2 fiber interface. Disabled (Default – Up)
- Enabled – The 100Base-X receiver is looped to the 100Base-X transmitter. Link #1’sfiber transmitter is taken off the interface.
Configuration Mode (Strap)
- Auto (default) enable management module to overwrite hardware switch settings
  Switch – Use onboard DIP switches
Cables
Fiber Optic Cable
- Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
- Single Mode: 9/125 micron (ITU-T 625)
Packet Transmission Characteristics
Bit Error Rate(BER)
- <10
Environmental Specifications
Operating Temperature
- 0 C to 50 C (32 F to 122 F)
Storage Temperature
- minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity
- 5% to 90% non-condensing
StorageHumidity
- 5% to 95% non-condensing
operating altitude
- Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR).
- 11.9
Maximum Power Consumption(watts)
- 3.5
MTBF (Hours) 484,202
- (Calculation model based on MIL-HDBK-217-FN2 @ 30 °C)
Mechanical – Hot Swapping Card
Edge Connecter
- 32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground andpower
Card insertion and removal
- Captive thumbscrews enable fast insertion and removal. Can be further tightened witha screwdriver.
Product Weight
Weight
- 0.15 kg, 0.33 lbs

Packaging

shipping weight
- 0.33 kg, .73 lbs
shipping dimensions
- 203 x 38 x 152 mm, 8 x 1.5 x 6 inches
Regulatory Approvals
Emissions
- FCC Part 15 Class A, EN55022 Class A
- CISPR 22 Class A
- CISPR 32:2015/EN 55032:2015 (Class A)
- CISPR 24:2010/EN 55024:2010
- EN61000-3-2
Immunity
- EN55024
Safety
- UL/EN/IEC 62368-1
- CAN/CSA C22.2 No. 62368-1
- UL 60950-1
- IEC 60950-1(ed 2); am1, am2
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
- CE
Laser Safety
- EN 60825-1:2007
- Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.
Environmental
- Reach, RoHS and WEEE Compliant
Other
- ECCN: 5A991
- HTSUS Number: 8517.62.0020
- Perle Limited Lifetime Warranty

High-Density Fiber Distribution from Fiber Switch Equipment at Corporate Headquarters

In this enterprise campus application, up to 18 Perle CM-100MM Multimode to Single mode MediaConverters are installed in the MCR1900 Media Converter Chassis. The 19th slot in the chassis is filled the MCR-MGT Management Module. All media converts in the chassis are managed by SNMP, Telnetor an internet browser interface. A remote fiber-enabled Ethernet switch is connected directly to the central MCR1900 Chassis. Another S-100MM Fiber to Fiber Media Converter is connected to a remote office switch. In all cases, multimode or single-mode fiber can be used. Fiber links can be extended upto 120km using single-mode fiber. perle-CM-100MM-Fast-Ethernet-Fiber-to-Fiber-Managed-Media-
Converter-Module-fig-1

Managed Ethernet over Fiber Links

Manage your multimode to single mode or multimode to multimode link with an MCR200 chassis housing a media converter and management module. Ideal for use in managed networks with low-density fiber applications, this Managed Media Converter is connected across a fiber link to a remotemedia converter. The copper or fiber link on the managed standalone unit can provide vital information and status to network management tools such as SNMP. perle-CM-
100MM-Fast-Ethernet-Fiber-to-Fiber-Managed-Media-Converter-Module-
fig-2

Fast Ethernet Multimode Switch to Multimode Switch

Extend the network distance between two Multimode Fiber Switches Two Fiber to Fiber Media Converters can extend the distance between Fiber Switches across a fiber link up to 120km in length. perle-CM-100MM-Fast-Ethernet-Fiber-to-
Fiber-Managed-Media-Converter-Module-fig-3

Single Mode / Single Fiber

Connect fiber ports over a single fiber strand ( also referred to as “Bi- Directional” BiDi ) When Single Strand fiber is used, a pair of Single Fiber Media Converters is needed for the fiber-to-fiber conversion. Perle Single Fiber Media Converters are also referred to as “Up/Down” models. For example the CM-100MM-S1SC20U (“Up”) and CM-100MM-S1SC20D (“Down”), shown below, must be used in pairs. An “Up” must be matched with a “Down” peer to deal with transmit and receive frequencies separately. perle-CM-100MM-Fast-Ethernet-
Fiber-to-Fiber-Managed-Media-Converter-Module-fig-4

CM-100MM-S1SC20UCM-100MM-S1SC20D
The majority of installations for single-mode fiber media converters are of the “dual connector” or “dual fiber” type where one fiber connection is used for transmit, the other for receive. These are physically “crossed” to match up the Transmit/Receive links.
However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized. WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDM technology relies on the fact that optical fibers can carry many wavelengths of light simultaneously without interaction between each wavelength. Thus, a single fiber can carry many separate wavelength signals or channels simultaneously.
So remember, if Single Strand fiber is used, you will need an “Up” Media Converter on one side and a “Down” Media Converter on the other for fiber-to- fiber conversion.
Perle offers a wide variety of Single Fiber (“Up/Down”) Media Converters to connect 10BaseT, Fast Ethernet and Gigabit to single fiber. Whether you need Managed or Unmanaged, Standalone or Modular Chassis Based, 20km or 120km, Perle has the right model to meet your fiber conversion requirement.

Select a Model to obtain a Part Number – CM-100MM Fast Ethernet Fiber to Fiber Managed Media Converter Module

Power

|
---|---|---|---|---|---|---
| | | | Budget| Wavelength| Fiber| Operating
Model| Port| Connector| Type| Min| Max| Min| Max| (dBm)| (nm)| Type| Distance

CM-100MM- M2ST2

| ****

Port 1

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

| | | | | | | | | | | (1.2 mi)
| ****

Port 2

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

| | | | | | | | | | | (1.2 mi)

CM-100MM- M2SC2

| ****

Port 1

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

| | | | | | | | | | | (1.2 mi)
| ****

Port 2

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

| | | | | | | | | | | (1.2 mi)
CM-100MM- M2LC2| Port 1| Dual LC| 100BASE-FX| -20.0| -12.0| -30.0| -14.0| 10.0*| 1310| MMF| 2 km

(1.2 mi)

---|---|---|---|---|---|---|---|---|---|---|---
| ****

Port 2

| ****

Dual LC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-30.0

| ****

-14.0

| ****

10.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

CM-100MM- S2ST20

| ****

Port 1

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual ST

| ****

100BASE-LX

| ****

-18.0

| ****

-7.0

| ****

-32.0

| ****

-3.0

| ****

14.0

| ****

1310

| ****

SMF

| ****

20 km

(12.4 mi)

CM-100MM- S2SC20

| ****

Port 1

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual SC

| ****

100BASE-LX

| ****

-18.0

| ****

-7.0

| ****

-32.0

| ****

-3.0

| ****

14.0

| ****

1310

| ****

SMF

| ****

20 km

(12.4 mi)

CM-100MM- S2LC20

| ****

Port 1

| ****

Dual LC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-30.0

| ****

-14.0

| ****

10.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual LC

| ****

100BASE-LX

| ****

-15.0

| ****

0.0

| ****

-34.0

| ****

-5.0

| ****

19.0

| ****

1310

| ****

SMF

| ****

20 km

(12.4 mi)

CM-100MM- S2ST40

| ****

Port 1

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual ST

| ****

100BASE-EX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1310

| ****

SMF

| ****

40 km

(25 mi)

CM-100MM- S2SC40

| ****

Port 1

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual SC

| ****

100BASE-EX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1310

| ****

SMF

| ****

40 km

(25 mi)

CM-100MM- S2LC40

| ****

Port 1

| ****

Dual LC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-30.0

| ****

-14.0

| ****

10.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual LC

| ****

100BASE-EX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1310

| ****

SMF

| ****

40 km

(25 mi)

CM-100MM- S2ST80

| ****

Port 1

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual ST

| ****

100BASE-ZX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1550

| ****

SMF

| ****

80 km

(50 mi)

CM-100MM- S2SC80

| ****

Port 1

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual SC

| ****

100BASE-ZX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1550

| ****

SMF

| ****

80 km

(50 mi)

CM-100MM- S2LC80

| ****

Port 1

| ****

Dual LC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-30.0

| ****

-14.0

| ****

10.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual LC

| ****

100BASE-ZX

| ****

-5.0

| ****

0.0

| ****

-34.0

| ****

-3.0

| ****

29.0

| ****

1550

| ****

SMF

| ****

80 km

(50 mi)

CM-100MM- S2ST120

| ****

Port 1

| ****

Dual ST

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual ST

| ****

100BASE-ZX

| ****

0.0

| ****

5.0

| ****

-35.0

| ****

-3.0

| ****

35.0

| ****

1550

| ****

SMF

| ****

120 km

(75 mi)

CM-100MM- S2SC120

| ****

Port 1

| ****

Dual SC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-31.0

| ****

-14.0

| ****

11.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

| ****

Port 2

| ****

Dual SC

| ****

100BASE-ZX

| ****

0.0

| ****

5.0

| ****

-35.0

| ****

-3.0

| ****

35.0

| ****

1550

| ****

SMF

| ****

120 km

(75 mi)

CM-100MM- S2LC120

| ****

Port 1

| ****

Dual LC

| ****

100BASE-FX

| ****

-20.0

| ****

-12.0

| ****

-30.0

| ****

-14.0

| ****

10.0*

| ****

1310

| ****

MMF

| ****

2 km

(1.2 mi)

Single Fiber Models ( Recommended use in pairs )

Power

|
---|---|---|---|---|---|---
| | | | Budget| Wavelength| Fiber| Operating
Model| Port| Connector| Type| Min| Max| Min| Max| (dBm)| (nm)| Type| Distance

CM-100MM- S1ST20U

|

Port 1

|

Dual ST

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single ST

|

100BASE-BX

|

-14.0

|

-8.0

|

-32.0

|

-3.0

|

18.0

|

1310/1550

|

SMF

|

20 km

| | | | | | | | | | | (12.4 mi)

CM-100MM- S1ST20D

|

Port 1

|

Dual ST

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single ST

|

100BASE-BX

|

-14.0

|

-8.0

|

-32.0

|

-3.0

|

18.0

|

1550/1310

|

SMF

|

20 km

| | | | | | | | | | | (12.4 mi)

CM-100MM- S1SC20U

|

Port 1

|

Dual SC

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single SC

|

100BASE-BX

|

-14.0

|

-8.0

|

-32.0

|

-3.0

|

18.0

|

1310/1550

|

SMF

|

20 km

| | | | | | | | | | | (12.4 mi)

CM-100MM- S1SC20D

|

Port 1

|

Dual SC

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single SC

|

100BASE-BX

|

-14.0

|

-8.0

|

-32.0

|

-3.0

|

18.0

|

1550/1310

|

SMF

|

20 km

| | | | | | | | | | | (12.4 mi)

CM-100MM- S1SC40U

|

Port 1

|

Dual SC

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single SC

|

100BASE-BX

|

-8.0

|

-3.0

|

-33.0

|

-3.0

|

25.0

|

1310/1550

|

SMF

|

40 km

| | | | | | | | | | | (25 mi)

CM-100MM- S1SC40D

|

Port 1

|

Dual SC

|

100BASE-FX

|

-20.0

|

-12.0

|

-31.0

|

-14.0

|

11.0*

|

1310

|

MMF

|

2 km

| | | | | | | | | | | (1.2 mi)
|

Port 2

|

Single SC

|

100BASE-BX

|

-8.0

|

-3.0

|

-33.0

|

-3.0

|

25.0

|

1550/1310

|

SMF

|

40 km

| | | | | | | | | | | (25 mi)

The minimum fiber cable distance for all converters listed is 2 meters. *Based on use with 62.5/125 micron multimode fiber.

Product Image|

Description

| Power Cord| Product Number
---|---|---|---
| CM-100MM-M2ST2 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles]. Managed or unmanaged operation| None| 05062010
Product Image|

Description

| Power Cord| Product Number
---|---|---|---
| CM-100MM-M2SC2 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles]. Managed or unmanaged operation| None| 05062000
| CM-100MM-M2LC2 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles] to 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles]. Managed or unmanaged operation| None| 05062020
| CM-100MM-S2ST20 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-LX 1310nm single mode (ST) [20 km/12.4 miles]. Managed or unmanaged operation| None| 05062040
| CM-100MM-S2SC20 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-LX 1310nm single mode (SC) [20 km/12.4 miles]. Managed or unmanaged operation| None| 05062030
| CM-100MM-S2LC20 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles] to 100Base-LX 1310nm single mode (LC) [20 km/12.4 miles]. Managed or unmanaged operation| None| 05062050
| CM-100MM-S2ST40 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-EX 1310nm single mode (ST) [40 km/24.9 miles]. Managed or unmanaged operation| None| 05062070
Product Image|

Description

| Power Cord| Product Number
---|---|---|---

| CM-100MM-S2SC40 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-EX 1310nm single mode (SC) [40 km/24.9 miles]. Managed or unmanaged operation| None| 05062060

| CM-100MM-S2LC40 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles] to 100Base-EX 1310nm single mode (LC) [40 km/24.9 miles]. Managed or unmanaged operation| None| 05062080

| CM-100MM-S2ST80 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (ST) [80 km/49.7 miles]. Managed or unmanaged operation| None| 05062100

| CM-100MM-S2SC80 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (SC) [80 km/49.7 miles]. Managed or unmanaged operation| None| 05062090

| CM-100MM-S2LC80 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (LC) [80 km/49.7 miles]. Managed or unmanaged operation| None| 05062110

| CM-100MM-S2ST120 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (ST) [120 km/74.6 miles]. Managed or unmanaged operation| None| 05062130
Product Image|

Description

| Power Cord| Product Number
---|---|---|---

| CM-100MM-S2SC120 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (SC) [120 km/74.6 miles]. Managed or unmanaged operation| None| 05062120

| CM-100MM-S2LC120 – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (LC) [2 km/1.2 miles] to 100Base-ZX 1550nm single mode (LC) [120 km/74.6 miles]. Managed or unmanaged operation| None| 05062140

| CM-100MM-S1ST20U – Fast Ethernet Fiber to Fiber Media Converter. Managed Module 100BASE-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-BX 1310nm TX / 1550nm RX single strand fiber, single mode (ST) [20 km/12.4 miles]. Managed or unm| | 05062590

| CM-100MM-S1ST20D – Fast Ethernet Fiber to Fiber Media Converter. Managed Module 100BASE-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-BX 1550nm TX / 1310nm RX single strand fiber, single mode (ST) [20 km/12.4 miles]. Managed or unm| | 05062600

| CM-100MM-S1SC20U – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-BX 1310nm TX / 1550nm RX single strand fiber, single mode (SC) [20 km/12.4 miles]. Managed or unm| None| 05062150

| CM-100MM-S1SC20D – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-BX 1550nm TX / 1310nm RX single strand fiber, single mode (SC) [20 km/12.4 miles]. Managed or unm| None| 05062160
Product Image|

Description

| Power Cord| Product Number
---|---|---|---
| CM-100MM-S1SC40U – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-BX 1310nm TX / 1550nm RX single strand fiber, single mode (SC) [40 km/24.9 miles]. Managed or unm| None| 05062170
| CM-100MM-S1SC40D – Fast Ethernet Fiber to Fiber Media Converter Managed Module, 100Base-FX 1310nm multimode (SC) [2 km/1.2 miles] to 100Base-BX 1550nm TX / 1310nm RX single strand fiber, single mode (SC) [40 km/24.9 miles]. Managed or unm| None| 05062180