Lenco MES-415 Portable DVD User Manual

Model: MES -415

USER MANUAL PORTABLE DVD

Dear Customer, thank you for purchasing this Portable DVD player. When opening the box for the first time, please check whether all the accessories are present. Before connecting parts and power, please carefully read the user manual and always keep these instructions close by your Portable DVD player.

Safety Instructions

• Before using this product, read and follow all warnings and instructions.
• This device is not intended for use by people (including children) with physical, sensory, or mental disabilities, or a lack of experience and knowledge unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety;
• This product is intended for household use only and not for commercial or industrial use.
• Do not expose to dripping or splashing.
• No naked flame sources, such as lighted candles, should be placed on or near the product.
• Ventilation should not be impeded by covering ventilation openings with items such as newspapers, tablecloths, curtains, and the like.
• Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
• Do not place objects filled with liquids, such as vases on or near the product.
• Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust, or vibration.
• Do not keep or store this product in wet conditions for a long period.
• Do not clean this product with water or other liquids.
• Do not block or cover the slots and holes in the product.
• Do not push foreign objects into the slots or holes in the product.
• Do not attempt to open this product yourself. There are no user-serviceable parts inside.

Warning

• Never remove the casing of this device.
• Never place this device on other electrical equipment.

Notice

• If at any time in the future you should need to dispose of this product please note that: All batteries and accumulators need to be removed from this product (Removal of Waste Batteries and Accumulators).
• Always bring your product to a professional to remove the built-in battery.

Power supply adaptor
Manufacturer: Shenzhen Mass Power Electronics Limited Model number: EFF0900150E1BA Use only the power supply listed in the user instructions
WARNING Do not ingest the battery, Chemical Burn Hazard (The remote control supplied with) This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
To prevent possible hearing damage, do not listen at high volume levels for long periods.

Box content:

1 x Remote control including battery
1 x Car Adaptor
2 x Headphone
2 x Car mounting bracket
Note: If some parts are missing please contact your dealer as soon as possible

Identification of Controls

Main Unit
MASTER TFT SCREEN

SLAVER TFT SCREEN

1. SD/MMC
2. POWER ON/OFF
3. HEADPHONE OUT JACKS
4. VIDEO/AUDIO OUT
5. VIDEO/AUDIO IN
6. USB
7. DC  OUT
8. DC IN 9-12V
9. ENTER
10. UP/DOWN/LEFT/RIGHT/VOL-/VOL+
11. SOURCE| 12. UP/DOWN
13. MODE
Slaver TFT menu setting.
14. LEFT/ VOL-/RIGHT / VOL+
15. BACK LIGHT Slaver TFT backlight
switch
16. POWER ON/OFF
17. AV IN
18. HEADPHONE OUT JACKS
19. DC IN
---|---

Remote control unit

1. SOURCE
   DVD/CARD/USB/AV IN.

2. MUTE
   Disable Audio output.

3. 0-9 NUMBER BUTTON
   Selects numbered items in a menu.

4. DISPLAY
   To display the playtime and status information.

5. 10+ BUTTON
   In order to select a track 10 or greater, first press 10+, For example; select track 12, first press 10+, and then press the number 2 button.

6. MENU/PBC
   Return to DVD root menu(DVD). PBC on/off switch (VCD).

7. AUDIO
   DVD: Press AUDIO repeatedly during playback to hear a different audio language or audio track, if available. CD/VCD: Press AUDIO repeatedly during playback to hear a different audio channel ( Left, Right, Mix, Stereo).

8. PLAY/PAUSE
   Press PLAY/PAUSE once to pause playback, pressing PLAY/ PAUSE a second time will resume the playback.

9. STOP
   When this button is pressed once, the unit records the stopped point, from where playback will resume if PLAY( )is pressed afterward. But if the STOP button is pressed again instead of the PLAY( ) button, there will be no resume function.

10. MODE
    Set LCD parameter(adjust brightness, contrast, and saturation).

11. VOL+

12. Forward Skip
    Go to next chapter/ track.

13. Reverse Skip
    Go to previous chapter/ track to the beginning.

14. BUTTON
    Press BUTTON allow skipping ahead at 5-level speed(X2->X4-> X8->X16->X32->PLAY), and press PLAY button return to normal playback.

15. BUTTON
    Press BUTTON allow skipping back at 5-level speed(X2->X4-> X8->X16->X32->PLAY), press PLAY button return to normal playback.

16. STEP
    Step the motion in DVD mode.

17. SEARCH
    Go to the time point, title, or chapter you want in DVD Mode.

18. SUBTITLE
    Press SUBTITLE repeatedly during playback to hear different subtitle languages.

19. ANGLE
    DVD: Press ANGLE will change the view angle, on DVDs that support this feature.

20. TITLE
    Return to the DVD title menu

21. ENTER
    Confirms menu selection..

22. SETUP
    Accesses or removes setup menu.

23. VOL-
    Adjust volume

24. REPEAT
    Press REPEAT during playback to select a desired repeat mode. DVD: you can play select repeat chapter/title/off. CD/VCD: you can select repeat single/all/off. MP3: you can select repeat single/folder/off.

25. SLOW
    Press the Slow button repeatedly to enter slow playback, and cycle between different speeds. The speeds are 1/2,1/4,1/8,1/16, and normal.

26. PROGRAM
    DVD/VCD: The program function enables you to store your favorite tracks from the disc. Press the PROGRAM button, then PROGRAM MENU will appear on the screen, now you can use the number key to direct input the titles, chapters, or tracks number and select the PLAY option. To resume normal playback, press PROGRAM and select the clear program option on the program menu, press PROGRAM again to exit the program menu.

27. ZOOM
    DVD/VCD: Use ZOOM to enlarge or shrink the video image. 1. Press ZOOM during playback or still playback to activate the Zoom function. The square frame appears briefly at the right bottom of the picture. 2. Each press of the ZOOM button changes the TV screen in the following sequence: 2X size – 3X size – 4X size -. 1/2 size – 1/3 size – 1/4size-normal size

JPEG: Use ZOOM to enlarge or shrink the picture.

1. Press ‘ZOOM’.
2. Use “ to enlarge, or “ ” to shorten the picture. Use the▲ ▼ ◀► buttons to move through the zoomed picture.

Setup Menu Setting

General Setup Page
Press SETUP button to get the setup menu. Use direction buttons ▲ ▼ ◀►to select the preferred item. After finishing settings, press SETUP again to the normal display. The following menu items can be changed: GENERAL: selects the GENERAL PAGE menu. AUDIO: selects the AUDIO PAGE menu. VIDEO: selects the VIDEO PAGE menu. PREFERENCE: selects the PREFERENCE PAGE menu.
General Setup Page
TV DISPLAY: selects the aspect ratio of the playback picture.
4:3 PANSCAN: if you have a normal TV and want both sides of the picture to be trimmed or formatted to fit your TV screen.
4:3 LETTERBOX: if you have a normal TV. In this case, a wide picture with black bands on the upper and lower portions of the TV screen will be displayed.
16:9:wide screen display.
TFT DISPLAY: Selects the TFT display to 16:9 or 4:3.
Angle Mark
Displays current angle setting information on the right-hand corner of the TFT screen if available on the disc.
OSD Language
You can select your own preferred language settings.
Closed Captions
Closed captions are data that are hidden in the video signal of some discs. Before you select this function, please ensure that the disc contains closed captions information and that your TV set also has this function.
Screen Saver
This function is used to turning the screen saver On or Off.
Last Memory
If this function is switched to ON, the DVD will resume play on the last known position, when the unit was stopped, powered down or dvd was reinserted.
AUTO STANDBY
This function is used to put the device in standby mode.
Audio Setup Page
Audio Setup Page
Downmix
This option allows you to set the stereo analog output of your DVD Player.
→LT/RT : Select this option if your DVD Player is connected to a Dolby Pro Logic decoder.
→Stereo: Select this option when output delivers sound from only the two front speakers.
Dolby Digital
The options included in Dolby Digital Setup are: ‘Dual Mono’ and ‘Dynamic ‘.
Dual Mono
→Stereo: Left mono sound will send output signals to the Left speaker and the Right mono sound will send output signals to the Right speaker.
→I-Mono: Left mono sound will send output signals to the Left speaker and Right speaker.
→R-Mono: Right mono sound will send output signals to the Left speaker and Right speaker.
→Mix Mono: Left and Right mixed mono sound will send output signals to Left and Right speakers.
Dynamic
Dynamic range compression.
Video Setup Page

Brightness, Contrastliue, Saturation: setting the video quality.
Preference Page

TV Type
Select the color system that corresponds to your TV when AV outputs. This DVD Player is compatible with both NTSC and PAL.
Preference Page
PAL – Select this if the connected TV is a PAL system. it will change the video signal of an
NTSC disc and output in PAL format. NTSC-Select this if the connected TV is an NTSC system. it will change the video signal of a PAL disc and output in NTSC format. Auto: Chang the video signal output automatically according to the playing disk format.
Audio: Selects a language for audio (if available).
Subtitle: Selects a language for the subtitle (if available).
Disc Menu: Selects a language for the disc menu (if available).
Default: Back to the factory setting.

Slaver TFT Menu Setting

Picture Page

Bright
Adjust screen Bright Setting.
Contrast
Adjust the screen Contrast Setting.
Colour
Adjust screen Color Setting.
LANG
Adjust Menu OSD Language
SCREEN
Adjust screen 16:9 or 4:3
RESET
Reset to default setting.

Parameters and specifications

Electronical parameters

System

Note: Design and specifications are subject to change prior notice.
Mounting the DVD in a Car
Use the supplied mounting kit to install the DVD players on the back of the vehicle’s headrests.

1. Align the angled support’s bolt to the screw hole on the back of the DVD unit. Turn the bolt clockwise and secure the support.

2. Lift the headrest off its leg supports. Align the horizontal support with the headrest leg slots and ensure the horizontal support rests securely on the top of the car seat. Reattach the headrest.

Remark: If the legs of the headrest are too thick for the opening of the horizontal support bar of the bracket, please unscrew the 4 screws of the support bar of the bracket to adjust the opening. In case the screws are too short, use the longer screws (provided in the gift box).

3. Grip the DVD firmly with both hands and slot the angled support firmly into the support bar. It will click. Ensure the entire unit is secure.

4. Adjust the angle of the DVD unit, then secure it by tightening the bolt on the right.

5. To remove the DVD from the horizontal support bar, support the DVD unit with one hand. With the other hand, firmly squeeze the release buttons on either side of the angled support and pull.
   • This unit should never be used by the vehicle’s driver or left unsecured in the vehicle while driving.
   • If this unit is being used in your vehicle, be sure that it is secured or held safely, and does nqobstruct any safety device, including air bags or seat belts.
   • All passengers should wear seat belts when using this unit in a moving vehicle.
   • If in doubt, please contact your vehicle manufacturer for further advice.

Guarantee

Lenco offers service and warranty in accordance with European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.
Important note: It is not possible to send products that need repairs to Lenco directly.
Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the instructions, specifications, and pictures in this documentation may
differ slightly from your particular situation. All items described in this guide are for illustration purposes only and may not apply to a particular situation. No legal right
or entitlements may be obtained from the description made in this manual.

Disposal of the Old Device

**** This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose of them in accordance with any applicable local laws of the requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in the treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

CE Marking

**** Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive (2014/35/EU) issued by the Commission of the European Community.

Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential requirements.
The declaration of conformity may be consulted via techdoc@lenco.com

Service

For more information and helpdesk support, please visit www.lenco.com Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, The Netherlands.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>