MCA furniture 40253 SX3 Nakuru Desk Installation Guide
- June 12, 2024
- MCA Furniture
Table of Contents
MCA furniture 40253 SX3 Nakuru Desk
Technical data
Item No.
| ET116G-2P4824
---|---
Column Stage|
2
Max. Load Capacity
| 50KG
Max. Speed|
25mm/s
Height Range
| 730-1230mm(with tabletop)
Tabletop Dimension|
1200x600x16mm Particle Board
Frequency
| 10%（Work continuously for 2 minutes, pause for 18 minutes）
Temperature|
0-40℃
Accessory list
Attention: The drawings below are for guidance only and they may differ slightly from the product and fittings received. Please contact customer service department if there are any missing tools or installation problems.
Tools Required
Component List
| No. | Part | Qty | No. | Part | Qty |
|---|
①
|
Front Tabletop
| 1|
②
|
Back Tabletop
| 1
③
|
Table Support Tube
| 2|
④
|
Column
| 2
⑤
|
Feet
| 2|
⑥
|
Beam Components
| 1
⑦
|
Baffle
| 1|
⑧
|
Power Plug
| 1
⑨
|
Cable Tie
| 4|
⑩
|
Switch Cord
| 1
⑪
|
Handset
| 1|
⑫
|
Table Connect Sheet Meta
| 2
Installation Diagram
STEP1
-
Set 3 Wooden Dowel Pins
-
Align the connecting sheet metal (12) of the two table plates with the holes as shown in the figure, press the two table plates, and then use a 5×5 allen key (C) to tighten the screws (G).
STEP2
- Tighten 4 screws(E)
- Cover the plugs 4 screws on left and right
- As shown in the figure, align the holes on the table and tighten the 12 screws(H) with a cross allen key C.
STEP3
STEP4
STEP5
STEP6
How to use handset
•
|
“▲”
| Adjust the desk upwards
---|---|---
•
|
“▼”
| Adjust the desk downwards
Operation
-
Button Lift Function
Press the “▲” or “▼” button to adjust the height of the desk. -
Reset Function
(1) When at the lowest position, long press the “▼” button for more than 5 seconds to enter the reset mode. The reset will be finished until the lift system rebound and stop after reaching the bottom.
(2) When the lifting system fails, release the button, long press the “▼” button, the reset will be finished until the lift system rebound and stop after reaching the bottom
Common fault treatment
The following tips will help you detected and eliminate the common fault and
error.
If the fault you met is not listed below, please contact with your supplier.
Only the manufacturer and professionals are capable for investigating and
correcting those fault and error.
Fault phenomenon
|
Method
---|---
No response while long pressing
- Check if all the cables be connected well down arrow after connected with a power supply
|
- Check if all the cables be connected well
- Contact your supplier or dealer
The desktop could not be lifted|
- Check if overloaded, max loading: 50kg
- Contact your supplier or dealer
Overwork (Duty cycle:Max 2 min on/ min OFF)|
- Restart it after suspend for 18 mins for the working time is too long
- Contact your supplier or dealer
Go down but not go up|
- Reset
- Contact your supplier or dealer
Downward sliding|
- Check if overloaded, max loading: 50kg;
- Contact your supplier or dealer
Attention
- Power supply: AC1 00V-240V,50/60HZ
- Service Environment: 0-40″C
- Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
- The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country’s environmental legislation, not the general household waste.
- Check carefully to ensure correct and complete assembly before using.
- Be familiar with all functions and program settings of the product before first use.
- Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences caused by this improper action will not be on manufacturers.
- Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
- Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment.
- Please make sure there is no hazard sources in your operating environment. e.g., do not litter the tools around. Always be careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
- Keep the original package of the equipment if necessary in case of the future use in transportation.
- If there appears damage of the power cord, please contact the manufacturer or a professional for replacement.
Waste disposal
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
The crossed-out bin means that this product includes electrical and electronic pieces that must not be disposed of in the regular domestic waste. Please dispose the Gaming desk separately at the recycling centre.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>