Avigilon ES-HD-IPM Outdoor HD Enclosure PoE Module Instruction Manual

Avigilon ES-HD-IPM Outdoor HD Enclosure PoE Module

Product Information

The Outdoor HD Enclosure PoE Module (ES-HD-IPM) is a device that utilizes POE (Power over Ethernet) and Hi-POE technology to provide power to all connected devices through the Ethernet cable. This ensures efficient and flexible network system operation, as well as user-friendly installation and cost- effectiveness.

Product Features

• Utilizes POE and Hi-POE technology
• Power supply through Ethernet cable
• Optimal efficiency and flexibility of the network system
• User-friendly installation
• Low costs

Product Specifications

• Model: ES-HD-IPM
• Power Source: Ethernet cable
• Compatibility: Compatible with various devices
• Installation: Outdoor

Product Usage Instructions

Before installing and using the Outdoor HD Enclosure PoE Module, please read the following instructions carefully:

1. Ensure that you have read and understood the safety rules mentioned in the user manual.
2. Prepare the product for use by safely disposing of the packaging material.
3. Assemble and install the module according to the instructions provided in the user manual.
4. Configure the module to meet your specific requirements. Refer to the configuration section of the user manual for detailed instructions.

Please note that any modifications to the product or improper use may void the warranty and can cause damage. Always refer to the user manual for guidance and contact customer support if you have any questions or concerns.

About this manual
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.

Typographical conventions

DANGER!
Explosion hazard. Read carefully to avoid the danger of an explosion.

DANGER!
High-level hazard. Risk of electric shock. Disconnect the power supply before proceeding with any operation, unless indicated otherwise.

WARNING!
Medium-level hazard. This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed.

INFO
Description of system specifications. We recommend reading this part carefully in order to understand the subsequent stages.

Notes on copyright and information on trademarks
The quoted names of products or companies are trademarks or registered trademarks.

Safety rules

The manufacturer declines all responsibility for any damage caused by the improper use of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care, the manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.

• The device must be installed only and exclusively by qualified technical personnel.
• Before any technical work on the appliance, disconnect the power supply.
• Do not use power supply cables that seem worn or old.
• Never, under any circumstances, make any changes or connections that are not shown in this handbook. Improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
• Use only original spare parts. Non-original spare parts could cause fire, electrical discharge, or other hazards.
• Before proceeding with installation check the supplied material to make sure it corresponds to the order specification by examining the identification labels (4.2 Product markings, page 4).
• Power supply to the product must be exclusively provided by the PoE cable (Power over Ethernet).
• This device was designed to be permanently installed on a building or on a suitable structure.
• When installing the device, comply with all the national standards.
• Any device which could be installed inside the product must comply with the current safety standards.
• If the installation is NEMA TYPE 4X, the installer must replace the cable glands of the product with NEMA TYPE 4X cable glands.
• For all connections, use cables that are able to withstand temperatures of at least 75°C (167°F).
• The product is designed to house only cameras that are properly certified.

Identification

Product description and type designation
The ES-HD-IPM module exploits in an optimal way the POE and Hi-POE technology, using the power supplied by the Ethernet cable as the sole source of power for all the devices connected, thus ensuring the maximum efficiency and flexibility of the network system as well as user-friendly installation and low costs. The innovative IPM (Intelligent Power Management) system enables extremely quick and easy installation with the use of a single Ethernet connecting cable. The analog system, with previously installed camera housings, can be retrofitted on IPM system simply by changing the slide and the internal electronics. This enables the digital conversion, speeding up the installation and thereby minimizing costs and environmental impact.

Product markings
See the label attached to the product.

Preparing the product for use

Any change that is not expressly approved by the manufacturer will invalidate the guarantee.

Unpacking and contents

Unpacking

• When the product is delivered, make sure that the package is intact and that there are no signs that it has been dropped or scratched.
• If there are obvious signs of damage, contact the supplier immediately.
• Keep the packaging in case you need to send the product for repairs.

Contents
Check the contents to make sure they correspond with the list of materials as below:

• IPM module
• RJ45 cable
• Instructions manual

Safely disposing of packaging material
The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used. When returning a faulty product we recommend using the original packaging for shipping.

Assembling and installing

The assembly and installation must be performed only by skilled personnel.

Installation

Preparing the Housing
To retrofit the ES-HD-IPM module to Avigilon HD enclosures, the existing control board, slide and heater (if equipped) must first be removed.

1. Remove all electrical connections from the circuit board (02)
2. Remove the fixing screws and the circuit board.
3. Loosen the screws fastening the internal supply slide (01).
4. Move the internal slide by sliding it until the holes coincide with the slide locking screws.
5. Remove the internal slide.
6. The locking screws will be reused to secure the IPM module, do not discard these.
7. For ES-HD-HWS or ES-HD-HWS-LG housings, remove the heater plate (03) by unscrewing the two fixing screws.

Completing the External Installation
Refer to the housing manual for details on installing the cable glands, mounting the brackets and adjusting the air intake valves.

How to install the camera

It is possible to install only PoE type cameras.

• Mount the camera using the supplied screws (01) and spacers (02).

• Apply at least one spacer to guarantee electrical isolation between the slide and the camera.

• Position the camera lens close to the glass to avoid visual interference or optical reflections.

• Connect the camera to the J2 connector (PoE OUT) with the supplied cable (03).

• Refit the slide in its housing and fix the previously loosened screws.

PoE cable connection
Connect the PoE cable from the Power Injector to the J1 connector.

Before powering the device, you must set the maximum power consumption of the housing operating on dip switch SW1 (7 Configuration, page 8).

Connection of the blower for ES-HD-CWS and ES-HD-CWS-LG
Connect the fan cable to the J4 connector.

Configuration

Before powering the device, you must set the maximum power consumption of the housing operating on dip switch SW1.

ABSORBED POWER CONFIGURATION

SW1| Maximum power
OFF| PoE class 3 (13W max)
ON| Hi-PoE class 4 (25W max)

According to the absorbed power, the system can supply the options described in the table.

ES-HD-IPM : AVAILABLE MODELS AND FEATURES

Operating temperature| Injector| Camera| Heating| Fan with double air filter
-10°C / +60°C (14°F / 140°F)| PoE classe 3 (13W)| PoE max. class 2 (7W)| –| ✓
Hi-PoE class 4 (25W)| PoE max. class 3 (13W)| –| ✓
-10°C / +50°C (14°F / 122 F°)| PoE classe 3 (13W)| PoE max. class 2 (7W)| –| –
Hi-PoE class 4 (25W)| PoE max. class 3 (13W)| –| –
-30°C / +50°C

(-22°F / +122°F)

| Hi-PoE class 4 (25W)| PoE max. class 3 (13W)| ✓| –
Hi-PoE class 4 (25W)| PoE max. class 3 (13W)| ✓| –

Switching on

The automatic pre-heating (de-ice) process could be started whenever the device is switched on and the air temperature is below 0°C. This process is used to ensure that the device works properly even at low temperatures. The duration ranges between 60 and 120 minutes, depending on conditions.

During the lighting phase the device reads the status of the dip switch and automatically detects all the connected options for the correct energy management of the housing. The 6 LEDs shown in the figure allow to check the product’s operating status.

Refer to the table to identify the operating status.

OPERATING STATUS

LED| LED

Status

| Apparatus Status
LD1 (Po-

wer)

| Off| The device is not powered
On| The device is correctly powered
LD2

(Camera)

| Off| The camera is not connected or Cold Start is active
On| The camera is correctly powered
1 flashing| The camera has a low identifi- cation resistance
2 flashings| The camera has a high identi-

fication resistance

5 flashings| The camera has an excessive energy consumption
9 flashings| The camera requires more energy than the available
LD3 (Not used)
LD4 (He-

ater)

| Off| Heating is not available or po-

wer available is not sufficient

1 flashing| Heating is inactive
On| Heating is active
LD5 (Not used)
LD6

(Cold Start)

| Off| Heating is not available
1 flashing| The pre-heating procedure is inactive
On| The pre-heating procedure is underway

Cleaning

Window and plastic cover cleaning (PC)
Avoid ethyl alcohol, solvents, hydrogenated hydrocarbons, strong acid, and alkalis. Such products may irreparably damage the surface.

Surface dirt should be rinsed away with water and then the window cleaned with a neutral soap diluted with water, or specific products for spectacle lens cleaning. These should be applied with a soft cloth.

Disposal of waste materials

This symbol mark and recycling system are applied only to EU countries and not applied to countries in other areas of the world.

Your product is designed and manufactured with high-quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local Community waste collection or Recycling center. In the European Union, there are separate collection systems for used electrical and electronic products.

Technical data

Mechanical

• Unit weight: 0.6 kg (1.32 lb)

Electrical

• Power absorbed in input: PoE Class 3 (13W) or Hi-PoE class 4 (25W) selectable from dip switch
• Available power for the camera (PoE IN class 3): PoE class 2 (7W)
• Available power for the camera (Hi-PoE IN class 4): PoE class 3 (13W) with Ton -10°C ±2°C “cold start” function
• Data line: 10/100Base-T
• Heating: 8W, electronically controlled, Ton 20°C±2°C (68°F±4°F), Toff 23°C±2°C (73.4°F±4°F)
• Fan with thermostat for camera cooling for versions with double air filter: Ton 35°C±2°C (95°F±4°F), Toff 32°C±2°C (89.6°F±4°F)
• Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus

© — 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted with respect to any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or its licensors.

AVIGILON, CAPTURE IT WITH CLARITY, HDSM, HIGH DEFINITION STREAM MANAGEMENT (HDSM), THE BEST EVIDENCE and LIGHTCATCHER are unregistered and/or registered trademarks of Avigilon Corporation in Canada and other jurisdictions worldwide. Other product names mentioned herein may be the unregistered and/or registered trademarks of their respective owners. ™ and ® are not used in association with each trademark in this document.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>