Swiss Madison TT-5 12 Inch Rough-In Two-Piece Toilet Installation Guide
- June 12, 2024
- Swiss Madison
Table of Contents
**Swiss Madison TT-5 12 Inch Rough-In Two-Piece Toilet Installation Guide
**
PRIOR TO INSTALLATION
- Inspect toilet to ensure no damages have occurred while in shipping.
- Please compare parts with package list. If anyone is damage or missing, please contact us. We will replace new one for you.
- Observe all plumbing and building codes in accordance with your state and local requirements.
- All dimensions are nominal! Be sure to measure your toilet prior to installatton.
- The step-by-step guidelines in the installation instructions are a general reference.Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional.
- Read installation and maintenance installation thoroughly before installing. Be sure to use proper tools and always wear proper personal safety accessories for your protection.
- Two people are recommended to handle and install this product as it is fragile.
- Fill valve has been factory-tightened to design specifications. If re-tightening is required, use a wrench a tighten one turn past finger tight.
- Make sure the supply pressure is a minimum of 35 psi (2.5kg/cm³), the toilet will not function properly without minimum water pressure
PRODUCT SIZE
PARTS LIST
-
Bowl
-
Tank
-
Flush Lever
-
Fill Valve (Pre-installation)
-
Flush Valve (Pre-installation)
-
Tank To Bowl Gasket
-
Tank-To-Bowl Screws And Nuts
-
Slow Close Seat (include screws and nuts)
-
Wax Ring
-
Bolt Caps (2)
-
Bowl-To-Floor Screws And Nuts
Before You Start
Turn Off Water Supply
Flush to remove water from tank; sponge remaining water from bowl before removing toilet.
Clean Flange
Recommended fitting type for back-to-back installations.
BACK-TO-BACK INSTALLATION
Depending upon your plumbing and venting conditions, the flow from the toilet
in a back-to-back installation may create a vacuum on the system and draw
water from the opposing bowl. The National Standards Plumbing Code prohibits
the use of a cross fitting for drainage as throw over is possible. The code
does approve a directional “Y” style fitting with proper venting to direct the
water downward and away from the other toilet.
NOTE: 1/4″ EZ-BOLTS INCLUDED. IF 5/16″ BOLTS ARE REQUIRED, PURCHASE SEPARATELY.
Press firmly
Apply weight evenly. Do not move after placement. Water tight seal may break.
Hand tighten only. Do not over tighten.
Install tank bolts in bottom of tank as shown.
Tighten handles alternately until the tank contacts the front and back of the bowl achieving china-to-china contact.
NOTE: To ease installation, push down on the top of the tank while
tightening handles
A Connect water supply line. (Sold separately) Hand tighten nut.
B Turn on water supply.
WARNING: Overtightening of water supply line nuts could result in breakage and potential flooding. If the connection leaks after hand tightening, replace the supply line. Do not use any type of sealant on the water supply connection. Use of plumber’s putty, pipe dope, or any other type of sealant will void the warranty
SINGLE FLUSH
Adjust water level to level indicated on tank by turning water level
adjustment knob to move float cup up or down.
TOILET SEAT INSTALLATION
UNSCEW THE NUTS.
INSERT SCREW INTO THE PLATE.
SLIDE THE PLATE WITH SCREW TO MOUNTING TRACK.
INSERT THE SCREW TO THE HOLE OF SEAT ON THE BOWL.
ADJUST SEAT TO ALIGN TO THE BOWL.
TIGHTEN NUTS ALTERNATELY UNTIL THE TANK CONTACTS THE FRONT AND BACK OF THE
BOWL ACHIEVING CHINA-TO-CHINA CONTACT.
WARNING:
- The load capacity for magnet holder and hook is approximately 3 lbs. Please avoid hiting and scratching the protective layer on the surface.
- If you require technical support or in the unlikely event that your purchase is faulty please EMAIL US for immediate assistance. Faulty product claims made within the 2 year warranty period will be replaced free of charge.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>