XCHO TC-028 Remote Dog Training Collar User Manual
- June 12, 2024
- XCHO
Table of Contents
XCHO TC-028 Remote Dog Training Collar
PRODUCT INFORMATION
TC-028
Explanation of Attention Words and Symbols Used in This Guide
- WARNING: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
- WARNING: indicates a hazardous situation which, if not avoided, could result in death or serious injury.
- CAUTION: used With the safety alert symbol, indicates a hazardous situation which. if not avoided, could result in minor or moderate injury.
- CAUTION: without the safety alert symbol, is used to address practices not related to personal injury,
- NOTICE: is used to address practices not related to personal injury.
- PROHIBITED: indicates that the operation is prohibited.
Safety Instructions
WARNING: It is forbidden to be used on aggressive dogs. A aggressive dog may cause serious injury or even death to the owner or others. If you are not sure whether this product is suitable for your dog. please consult a professional dog trainer.
Children are prohibited from playing with this product. Keep collar away from children.
CAUTION
- Please make sure your dog is healthy before using the product. If you are unsure about this, please consult your veterinarian.
- When the collar is turned on, the human body should not directly touch the E-Shock contact Of the product.
- If rash or sore is found at the contact location of E-Shock probe, please stop using this product until the skin recovers.
- Collar wearing time should not exceed 12 hours per day, and please adjust the wearing position every 1-2 hours.
- This product is suitable for dogs over weighing more than 8 pounds and the age of 6 months.
- It is forbidden to use this product as a matching collar for pet leashes.
CAUTION
- It is important to check the E-Shock contact probe area of the dog’s neck every day for Rashes&Sores.
- The long hair around the dog’s throat can be properly shortened, but it is not recommended to be completely shaved.
- Remove the collar before vigorous play with the dog.
What’s in the Box
- Training Remote 1
- Training Receiver (Collar) 1
- Test Unit & Probe Driver 1
- Long and Short E-Shock Probes 2 pair
- Probe Protective Cover 2 Pair
- USB Charging Cable 1
- User Manual 1
In the 2-pair package, items No. 2, 4, 5, will have one more piece.
Learn About Your Traine
-
Dog Channel
-
Key Board
-
Beep
-
E-ShOCk Boost
-
E-Shock
-
Vibration
-
color display
-
E-Shock Level
-
Vibration Level
-
USB Charging
-
Hand trap Hole
-
Buckle
-
Slider Buckle
-
Adjustable Strap
-
USB Charging
-
Power ON&OFF/ Pairing Key
-
E-Shock Probe
-
LED Indicater
-
Probe Mount
-
Test Light
-
Test Contact
Start Using Collar
-
Charge the Collar First
- Use the type-c USB cable to charge the product.
- It can be charged in both off-state and on-state.
-
Turn on The Devices
- Collar: Long press the Power Key for two seconds to power on, long press for two seconds to power Off.
- Remote: The remote control does not have an onloff key, and it automatically enters the standby state when itis not working.
-
Operation &Test The Collar Features
Before using the product officially, please test whether the basic functions of the product can work normally.- Dog Channel
- lock Keyboard
- Adjust E-Shock Level O means turning off the E-Shock function
- If the level is above 50. the red prompt exclamation mark will light up.
- Adjust Vibration Level
-
Wearing The Collar
-
Determine the length of the collar that fits the dog’s neck
-
Re-thread the extra strap into the slide buckle
-
Wear the collar around the dog’s neck in a personally comfortable way. Make Sure the device is just in front Of the dog’s throat
-
Please ensure to fit the product snugly, yet loose enough to allow one finger to fit between the strap and your dog’s neck. NOTE : Proper use of the slide buckle can prevent the collar from becoming loose around your pet’s neck.
-
Start Training
How to Train
Some Training Guides
Pet Treats:
If you’re attempting to teach your dog a behavior, make Sure your dog
understands what you want before introducing E-Shock stimulation. You can do
this using your dog’s favorite treats. When Training Begins: You can begin
basic obedience training without the training collar as soon as you bring your
puppy home.
Stopping Unwanted Behavior :
The level of stimulation should be enough to interrupt your dog and give you
the ability to redirect your dog’s attention to another behavior. It’s best if
the behavior you redirect your dog to is “incompatible” with the unwanted
behavior. NOTE: using praise or treats immediately after the correct response
is great for encouraging your dog to repeat the desired behavior.
C ollar Conditioning :
You don’t want your dog to only associate wearing the training collar with
being corrected. While your dog is wearing the collar, make sure to spend
ample time playing and letting your dog be a dog.
Timing :
For static training to work properly, timing is very important. You should
apply the static stimulation immediately (within 2 seconds) of an undesirable
behavior. This will help your dog make the association between the undesirable
behavior and the static stimulation. If your dog seems nervous, scared or
confused after applying a static stimulation, stop using the stimulation and
make sure your dog has learned an appropriate behavior that will remove the
static stimulation and/or earn him a reward. For more training techniques,
please refer to professional books or consult a pet trainer.
Find the Best E-Shock Level for Your Pet
Important : Always start at the lowest level and work your way up. The Remote Trainer has 99 E-Shock levels. This allows you to choose the E-Shock level that is best for your pet.
We recommend training with beep and vibration, or the lower levels Of E-Shock when needed. In most cases E- Shock levels 1—50 will be adequate for your training needs. Once you have placed the training collar on your pet, it is time to find the “RECOGNITION LEVEL”. The “recognition level” is the stimulation level that your dog begins to notice. It should not make your pet uncomfortable.
Follow the steps below to find your pet’s recognition level:
- Choose level 1, and press E-Shock button continuously for 1 to 2 seconds. A slight change in your pet’s behavior, such as looking around in curiosity, scratching at his collar, or flicking his ears, indicates the Recognition Level that is best for him.
- If your pet shows no reaction, repeat this several times before moving to high E-Shock level.
- Choose level 2 and press E-Shock button continuously for 1 to 2 seconds.
- If your pet shows no reaction, repeat this level several times before moving up to the next level.
- Move up through the E-Shock levels until your pet reliably responds to the shock.
- If your pet continues to show no response at Level 16, check the fit of the training collar. You might also want to test it on your hand at a lower level to ensure the collar is working.
How to Pairing
- When the receiver is turned off, press and hold the power button for more than 4 seconds, the blue light in the middle starts to flash, and the receiver enters the pairing state. The pairing state will last for 15 seconds.
- Select the dog channel to be paired. Dog Channel
- Press any key of sound, vibration, and E-shock to pair with the receiver. If the pairing is successful, the receiver will emit
Replace Probe
- Select Probes & Covers
- Mount Probes & Unmount Probes
Charging
- Use the type-c USB cable to charge the product.
- It can be charged in both off-state and on-state.
Regarding the well-being of your dog
About “Collar Sores”
The milliamps generated from the receiver of training collars simply cannot generate enough heat necessary to do tissue damage. The real problem comes from inappropriate wear of the collar receiver to the skin.
Pressure necrosis, or what many in the industry call “collar sores”, can happen if the receiver is not being worn properly. They also occur if the collar is kept on the dog for too long of a period Of time. There are two reasons:
- Improper fit
- Improper wear time
Please pay attention to your dog’s neck when you begin using a training collar. A few times throughout the day take a peek and see how the skin looks. Make sure the fit is correct and notice if there is the beginning signs of redness. If so, move the receiver to the opposite side Of the neck or take the collar off for a bit to increase airflow and circulation to the skin.
- The Receiver collar is not a regular collar and not recommended to put on a leash to walk your dog. (Doing so during pulling may hurt the dog due to protruding electrodes on the Receiver.)
- Do not put the collar on for over 12 hours, it may cause rashes or discomfort to your dog’s skin.
- Using the shock contact silicone sleeve can effectively protect the skin.
- Check the condition of the dog’s skin frequently and adjust the position of the receiver.
Other Precautions
- DO not operate the devices under temperature Of 1040F(400C) and above, doing so in such high temperature will decrease the performance of the batteries.
- Do not use the set in places with strong electromagnetic interference. This will greatly compromise the performance Of the product. Avoid dropping the devices on hard surface or inflict excessive force on them.
- When not in use, Turn off the products, and store the set in a cool dry place.
- If the Receiver has gotten dirty, wipe it clean with a damp cloth.
- The receiver has a high level of waterproof function. Do not submerge the Receiver into water for long period of time, even though it is waterproof.
- The remote control is not waterproof, and cannot come into contact with water and other liquids. If the Remote fell into water, pick it up quickly and dry it with cloth as much as you can and let it out to dry. It should resume function normally once the moisture is dried out.
- The Static stimulation is not a pleasant experience for any dogs. Punishment is harsh way to train a dog. Always, the praise could encourage your dog for good behavior.
Troubleshooting
If the product is abnormal during use, you can do the following:
Terms of Use & Limitation of Liability
Terms of Use
Your use of this product means that you accept all terms, conditions and statements in this manual.
Correct Use
This product is designed for pets that need training. Proper use includes reviewing the entire User Manual included with the product and any specific “Caution” statements.
Prohibition of illegal or Prohibited Use
This product is only suitable for pets. This training device is not intended to harm or provoke pets. Using this product not in accordance with the instruction manual may violate local laws.
Scope Of Responsibility
The manufacturer is not responsible for any related damages, direct, indirect, punitive, non-major, and other indirect losses caused by incorrect use or abuse of this product. The buyer bears all risks and responsibilities Of using this product.
Modification of Terms and Conditions
The manufacturer reserves the right to change the terms, conditions and notices related to this product.
Certification Statements
This device complies with Part 15 Of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates usesand can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
The company declares under its own responsibility that this product complies with the basic requirements of CE (2014/30/EU) and RoHS (2011/65/EU). Without the approval of our company or the distributor, unauthorized changes or modifications to the equipment may violate the CE regulations, may cause the user to lose the right to operate the equipment, and invalidate the warranty.
Recycling Information &Battery Disposal
Please observe the regulations for electronic and electrical devices to be disposed of in the respective country. In some countries or regions this device must be recycled. If this device is no longer required, it must not be disposed Ofwith normal municipal waste. Separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. For more recycling information, please refer to local regulations.
Specifications
- Product name :Remote dog training collar
- Product model : T C-028
- Material: ABS plastic, nylon, stainless steel
- Battery capacity: remote control 300 mAh; receiver 300mAh
- Charging voltage: DC5V/1A
- Charging time: 1-1.5 hours
- Charging port: Type-C USB
- Wireless power: 0.0316mWÆ-15DBnP
- Remote control frequency: 33M FS
- Operating temperature: -IOC-40’C(32-104F),
- Standby time: 60 days for remote control; 15 days for
- Product wight: remote 45g; receiver+strap 65g
- Product size: remote 145mm•36rnm•12mm; receiver 68mm • 37mm*31mm
Scope of application:
All kinds of dogs. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harrnful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, vfiich can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to vålich the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Designed and Manufactured in China
Version: I .O
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>