MARZ DESIGNS MARZ-TERR-1-SS Terra 1 Wall Light Installation Guide
- June 12, 2024
- Marz Designs
Table of Contents
INSTALLATION GUIDE, 240V
Terra 1 Surface
FRAGILE FINISHES PLEASE WEAR GLOVES DURING
INSTALL
MARZ-TERR-1-SS Terra 1 Wall Light
Attention!
Please carefully read instructions before use
| PRODUCT: | Terra 1, Surface 240V |
|---|---|
| PRODUCT CODE: | MARZ-TERR-1-SS |
| RATED VOLTAGE: | 220-240VAC |
| FREQUENCY: | 50 HZ |
| FITTING: | 1 lamp 4.5W LED |
| LAMP TYPE: | G9 |
DANGER: Lights must be installed by a qualified electrician. Electric shock risk.
- Turn off electrical power before beginning installation and use caution when installing.
- Please do not modify or adjust any fixture in a way that is not clearly stated or intended.
- Always ensure the power is off and the luminaire has cooled down before performing any maintenance to the fitting.
- To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
- To avoid electric shock, do not touch this item if your hands are wet.
- To clean, wipe with a soft damp cloth. Do not soak or immerse the luminaire in water or other liquids.
- Do not use if any breakage or distortion is found on the wiring or socket, or if the products have been wet.
- Marz Designs is not responsible for any damages caused by not following the provided instructions.
This luminaire is intended for mounting to a ceiling or wall:
- Carefully check luminaire and wiring for damage before use. Do not use the fixture if it is damaged.
- Ensure that local voltage and frequency match the marking.
- For indoor use only.
- Do not disassemble the structure of the fixture.
- Do not leave children alone with the product.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer to avoid hazard.
- Please use reliable suspending and fixing devices to avoid danger.
- This is a Class I device and must be connected to a protective grounding.
- Terminal block and connection box is not included.
- Only qualified personnel may install this device. Please observe national installation regulations.
Terminal block shall conform
to IEC 60998-2-1 or IEC 609982-02 and must comply with the following
specifications:
- With screw or screw-less terminal
- Two terminal poles;
- Rated voltage: 250V
- Rated connecting capacity: 10 A; 3 x 0.75-1.5mm²
- During installation, ensure that the basic insulation of the supply lead does not touch the ceiling/wall cover. Use proper insulation so that the clearance and distance between the live parts and the ceiling/wall cover is more than 6.5mm between the basic insulation of the supply lead and 3.6mm between the ceiling/wall cover.
- Keep the terminal block inside the ceiling/wall cover or fixed to the ceiling/wall.
NOTE
Make wire connections.
For 240V attach NEUTRAL wire from fixed installation to the black cable marked
with “N”. Attach LIVE wire from fixed installation to the white cable marked
with “L”. Attach EARTHING wire from fixed installation to the yellow/green
cable.
INSTRUCTIONS
- Drill 32mm hole in surface using holesaw to allow for cable termination.
- Connect electrical leads from the supply to the leads from the Fixture. Ensure the wires are secure and no bare wires are exposed, using an enclosed junction box.
- Use countersunk screws (not provided) to fix the Fixture (B) to Surface (A).
- Slide Ceramic Shade (C) over Fixture (B).
- Push the Light Globe (D) into the Fixture Socket.
- Screw the Glass cover (E) onto the Fixture Socket using the Glass cover (E) to hold the ceramic shade in place. CAUTION: Align threads properly for a smooth rotation before twisting to avoid jamming. Do not overtighten the globe.
www.marzdesigns.com
Revision A
DOI: 03/08/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>