Marz Designs MARZ-TERR-00-SS Terra 00 Surface Sconce Installation Guide
- June 12, 2024
- Marz Designs
Table of Contents
- Attention!
- **DANGER: Lights must be installed by a qualified electrician.
- This luminaire is intended for mounting to a ceiling or wall:
- Terminal block shall conform to IEC 60998-2-1 or IEC 60998- 2-02 and must
- Terra 00 Surface
- Customer Support
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Marz Designs MARZ-TERR-00-SS Terra 00 Surface Sconce
Attention!
Please carefully read instructions before use.
PRODUCT
| Terra 00, Surface 240V
---|---
PRODUCT CODE:|
MARZ-TERR-00-SS
RATED VOLTAGE:
| 220-240VAC
FREQUENCY :|
50 HZ
FITTING :
| 1 lamp 4.5W LED
LAMP TYPE|
G 9
**DANGER: Lights must be installed by a qualified electrician.
Electric shock risk.**
- Turn off electrical power before beginning installation and use caution when installing.
- Please do not modify or adjust any fixture in a way that is not clearly stated or intended.
- Always ensure the power is off and the luminaire has cooled down before performing any maintenance to the fitting.
- To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
- To avoid electric shock, do not touch this item if your hands are wet.
- To clean, wipe with a soft damp cloth. Do not soak or immerse the luminaire in water or other liquids.
- Do not use if any breakage or distortion is found on the wiring or socket, or if the products have been wet.
- Marz Designs is not responsible for any damages caused by not following the provided instructions.
This luminaire is intended for mounting to a ceiling or wall:
- Carefully check luminaire and wiring for damage before use. Do not use the fixture if it is damaged.
- Ensure that local voltage and frequency match the marking.
- For indoor use only.
- Do not disassemble the structure of the fixture.
- Do not leave children alone with the product.
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer to avoid hazard.
- Please use reliable suspending and fixing devices to avoid danger.
- This is a Class I device and must be connected to a protective grounding.
- Terminal block and connection box is not included.
- Only qualified personnel may install this device. Please observe national installation regulations.
Terminal block shall conform to IEC 60998-2-1 or IEC 60998- 2-02 and must
comply with the following specifications:
- With screw or screw-less terminal
- Two terminal poles;
- Rated voltage: 250V
- Rated connecting capacity: 10 A; 3 x 0.75-1.5mm²
- During installation, ensure that the basic insulation of the supply lead does not touch the ceiling/wall cover. Use proper insulation so that the clearance and distance between the live parts and the ceiling/wall cover is more than 6.5mm between the basic insulation of the supply lead and 3.6mm between the ceiling/wall cover.
- Keep the terminal block inside the ceiling/wall cover or fixed to the ceiling/wall.
Terra 00 Surface
INSTRUCTIONS
- Drill 6 5 m m hole in surface using hole saw to allow for cable termination . Use Anchors ( not provided) to fix the Universal Mounting Plate (B) to Surface (A).
- Connect electrical leads from the supply to the leads from the Fixture . Ensure the wires are secure and no bare wire s are exposed , using an enclosed junction box.
- Install the Canopy ( C ) to the Surface ( A ) over he Universal Mounting Plate ( B ) and secure in place with screw head Caps (D) supplied.
- Slide Shade (E) over Fixture.
- Wind Lock Ring ( F ) on to Fixture to secure Shade (E) in place.
- Push the Light Globe ( G ) into the Fixture Socket.
- Screw the Glass Cover ( H ) on to the Fixture Socket . CAUTION : Align threads properly for a smooth rotation before twisting to avoid jamming. Do not over-tighten the globe.
NOTE
Make wire connections. For 240V attach NEUTRAL wire from fixed installation to the black cable marked with “ N ” . Attach LIVE wire from fixed installation to the white cable marked with “ L ” . Attach EARTHING wire from fixed installation to the yellow/green cable.
Customer Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>