ADJ ENCORE LP5IP RGBL LED Par User Manual

ADJ ENCORE LP5IP RGBL LED Par

©2023 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their respective companies.
ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

DOCUMENT VERSION

• Due to additional product features and/or enhancements, an updated version of this document may be available online.
• Please check www.adj.com for the latest revision/update of this manual before beginning installation and/or programming.

Date| Document Version| Software Version| DMX Channels| Notes
---|---|---|---|---
03/03/2022| 1.0| 1.03| 4 / 7 / 8 / 10 / 13 / 16

Channels

| Initial Release
05/04/2022| 1.1| N/C| No Change| Updated Specifications
10/03/2022| 1.2| N/C| No Change| Updated Dimensions
03/13/2023| 1.3| 1.04| No Change| Updated DMX Traits, Specifications
05/19/2023| 1.4| N/C| No Change| Removed Fan Modes from Menu & DMX Traits

• Europe Energy Saving Notice
• Energy Saving Matters (EuP 2009/125/EC)
• Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!

INTRODUCTION

Unpacking: Thank you for purchasing the Encore LP5IP by ADJ Products, LLC. Every Encore LP5IP has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fi xture for any damage and be sure all accessories necessary to operate the unit have arrived intact. In the event that damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without fi rst contacting customer support.
Introduction: The ADJ Encore LP5IP is a DMX intelligent, heavy duty Par. To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit for future reference.
Customer Support: Contact ADJ Service for any product related service and support needs. Also visit forums.adj.com with questions, comments or suggestions.

• Parts: To purchase parts online visit:
• http://parts.adj.com (US)
• http://www.adjparts.eu (EU)
• ADJ SERVICE USA – Monday – Friday 8:00am to 4:30pm PST
• Voice: 800-322-6337 | Fax: 323-582-2941 | support@adj.com
• ADJ SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
• Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | support@adj.eu

ADJ PRODUCTS LLC USA

• 6122 S. Eastern Ave. Los Angeles, CA. 90040
• 323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

• Junostraat 2 6468 EW Kerkrade, The Netherlands
• +31 (0)45 546 85 00 | Fax +31 45 546 85 99
• www.americandj.eu | info@americandj.eu

ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000 +52 728-282-7070

CAUTION! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service, please contact ADJ Products, LLC.
Do not discard the shipping cartoon in the trash. Please recycle when ever possible.

LIMITED WARRANTY (USA ONLY)

• A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specifi c warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
• B. For warranty service, you must obtain a Return Authorization number (RA#) before sending the product back—please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All shipping charges must be prepaid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package and packaging material. No accessories should be shipped with the product. If any accessories are shipped with the product, ADJ Products, LLC shall incur no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
• C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is modifi ed in any manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because it was not properly maintained as set forth in the product instructions, guidelines and/or user manual.
• D. This is not a service contract, and this warranty does not include maintenance, cleaning, or periodic checkup. During the period specifi ed above, ADJ Products, LLC will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August 15, 2012, and bear identifying marks to that effect.
• E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured.
• F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by ADJ Products, LLC in connection with this product, including warranties of merchantability or fi tness, are limited in duration to the warranty period set forth above. And all warranties, whether expressed or implied, including warranties of merchantability or fi tness, are limited in duration to the warranty period set forth above. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall ADJ Product, LLC be liable for any loss and/or damage, direct and/or consequential arising out of the use of, and/or inability to use this product.
• G. This warranty is the only written warranty applicable to ADJ Products, LLC products, and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS

• Non-LED Lighting Products = 1-Year (365 Days) (Including Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands, Power/Data Distribution, etc. excluding LED and lamps)
• Laser Products = 1-Year (365 Days) (excluding laser diodes which have a 6-Month Limited Warranty)
• LED Products = 2-Year (730 Days) (excluding batteries which have a 180 Day Limited Warranty)
• NOTE: 2-Year (730 Days) Limited Warranty ONLY applies to product purchased within the United States. StarTec Series = 1-Year (365 Days) (excluding batteries which have a 180 Day Limited Warranty)
• ADJ DMX Controllers = 2 Year (730 Days)
• American Audio Products = 1 Year (365 Days)

WARRANTY REGISTRATION
The Encore LP5IP carries a 2 year limited warranty. Please fi ll out the enclosed warranty card to validate your purchase. All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain an R.A. number by contacting our customer support team on our customer support number. All packages returned to the service department not displaying an R.A. number on the outside of the package will be returned to the shipper.

FEATURES

The ADJ Encore LP5IP is a versatile, heavy duty Par with five (5) 20W Quad LEDs (4-IN-1: Red, Green, Blue & Lime), a 10-degree beam angle, and all metal construction. It is IP65 outdoor rated to protect against, rain, snow and dust for temporary outdoor events. It offers flicker free operation for TV and film and linear white color temperature control from 2700K – 6500K.

INCLUDED ITEMS

• Power Cord (x1)
• Dual Side Frost Filter (x1)

IP65 RATED

The International Protection (IP) rating system is commonly expressed as “IP” (Ingress Protection) followed by two numbers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies Protection) indicates the extent of protection against particles entering the fixture, and the second digit (Water Protection) indicates the extent of protection against water entering the fixture. An IP65 rated lighting fixture is designed and tested to protect against the ingress of dust (6), and low-pressure water jets from any direction (5).
NOTE: THIS FIXTURE IS INTENDED FOR TEMPORARY OUTDOOR USE ONLY!
Maritime/Coastal Environment Installations: A coastal environment is seaside adjacent, and caustic to electronics through exposure to atomized salt-water and humidity, whereas maritime is anywhere within 5-miles of a coastal environment.

NOT suitable for maritime/coastal environment installations. Installing this fixture in a maritime/coastal environment may cause corrosion and/or excessive wear to the interior and/or exterior components of the fixture. Damages and/or performance issues resulting from installation in a maritime/coastal environment will void the manufactures warranty, and will NOT be subject to any warranty claims and/or repairs.

Maritime installations require additional preparation, and additional service intervals may be needed given the maritime use. In general, IP ratings presuppose freshwater conditions VS maritime conditions, which are typically more “caustic” to IP fixtures (both internally and externally). A duty-cycle may also be needed when units are not in use. During times of high humidity and colder temperatures, condensation may occur internally so the fixture may require a duty-cycle to bring it up to running temperature, allowing any accumulation of moisture to be expelled via the vent valve. Recommendations can change based on installation environmental circumstances. A waterproof dome or similar device is recommended for use in permanent outdoor installations. When using a dome, refer to manufacturer recommendations for duty-cycle.

NOTE: NOT ALL FEATURES LISTED ARE AVAILABLE ON ALL FIXTURES; THE FOLLOWING INSTRUCTIONS MAY NOT APPLY. CONTACT SUPPORT FOR ADDITIONAL DETAILS.

Exterior Maintenance: Inspect the exterior every 30-days. The unit must be powered off/disconnected. Inspect optics to determine if the lens is obstructed, then clean optics and chassis accordingly. Based on initial finding, schedule maintenance accordingly, keeping in mind that exterior maintenance will be required. Even if the luminaires are NOT in use, maintenance will still be needed given its location (exterior use). The use of a durable type of wax on the chassis is recommended since it will help prevent contaminant build up. Inspect both power and data lines for any signs of contaminants or corrosion. Periodically reapplying di-electric grease, especially in coastal environments. If any signs of corrosion/contaminants are present, clean thoroughly, and/or replace connectors, then reapply di-electric grease. Typically, this should be done annually, or any time an opportunity presents itself. As a preventive measure, annual replacement of both vent valves is recommended. The vent valve membrane can become contaminated and/or clogged causing improper venting of humidity within the luminaire. Inspect all mounting hardware as a precaution.

Interior Maintenance: Inspect the interior every 30-days. The unit must be powered off/disconnected.

• Inspect zoom/focus mechanism, clean optics, lubricate linear bearings (Krytox oil) as needed, inspect belts for wear
• Inspect all rotating effect wheels, manually rotate them, note any resistance
• Inspect all remaining rotating belts for any wear
• Inspect all fans, clean as needed, check rotation, check connections
• Inspect CMY module, manually move flags and check for signs of resistance, and if needed, clean guide rods first, then reapply a thin layer of grease (moly lube)
• Clean interior with low-volume compressed air, then clean optics prior to reassembly of head covers

Although the base has limited moving parts, the pan belt should also be inspected for wear. Remember to always perform an IP test anytime a cover is removed.
There is no specific time frame regarding the routine replacement of parts such as belts/stepper motors, PCBs, or LEDs. These items should only be replaced on an as needed bases, except for cooling fans, which should be replaced once the luminaries reach 10,000-hours. This is a prophylactic measure intended to keep the unit running as cool as possible, insuring proper function of all internal components. A complete service breakdown is available, please contact service@adj.com for any needed parts or manuals.

SAFETY GUIDELINES

THIS FIXTURE IS COMPOSED OF SOPHISTICATED ELECTRONIC COMPONENTS. TO GUARANTEE SMOOTH OPERATION, IT IS IMPORTANT TO FOLLOW ALL INSTRUCTIONS AND GUIDELINES IN THIS MANUAL. ADJ PRODUCTS, LLC IS NOT RESPONSIBLE FOR INJURY AND/OR DAMAGES RESULTING FROM THE MISUSE OF THIS FIXTURE DUE TO THE DISREGARD OF THE INFORMATION PRINTED IN THIS MANUAL. ONLY QUALIFIED AND/OR CERTIFIED PERSONNEL SHOULD PERFORM INSTALLATION OF THIS FIXTURE AND ONLY THE ORIGINAL RIGGING PARTS INCLUDED WITH THIS FIXTURE SHOULD BE USED FOR INSTALLATION. ANY MODIFICATIONS TO THE FIXTURE AND/OR THE INCLUDED MOUNTING HARDWARE WILL VOID THE ORIGINAL MANUFACTURER’S WARRANTY AND INCREASE THE RISK OF DAMAGE AND/OR PERSONAL INJURY. ONLY CERTIFIED PERSONNEL SHOULD PERFORM INSTALLATION OF THIS FIXTURE.

• PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
• DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
• GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
• DO NOT PLUG FIXTURE INTO A DIMMER PACK!
• NEVER OPEN THIS FIXTURE WHILE IN USE!
• UNPLUG POWER BEFORE SERVICING FIXTURE!
• NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
• KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
• RETINA INJURY RISK – MAY INDUCE BLINDNESS!
• SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
• MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS)
• MAXIMUM AMBIENT TEMPERATURE IS 113° F (45°C). DO NOT OPERATE THE DEVICE WHEN AMBIENT TEMPERATURE EXCEEDS THIS VALUE.
• MINIMUM DISTANCE TO FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METER).
• DO NOT TOUCH the fi xture housing during operation. Turn OFF the power and allow approximately 60 minutes for the fi xture to cool down before servicing.
• DO NOT shake fi xture, and avoid brute force when installing and/or operating fi xture.
• DO NOT operate fi xture if the power cord is frayed, crimped, damaged and/or if any of the power cord connectors are damaged and do not insert into the fi xture securely with ease. NEVER force a power cord connector into the fi xture. If the power cord or any of its connectors are damaged, replace it immediately with a new one of the same power rating.
• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between fi xture and other devices or a wall for proper cooling.
• When installing fi xture in a suspended environment, always use mounting hardware that is no less than M10 x 25 mm, and always install fi xture with an appropriately rated safety cable.
• Always disconnect fi xture from main power source before performing any type of service and/or cleaning procedure.
• Only handle the power cord by the plug end. Never pull out the plug by tugging the wire portion of the cord.
• During the initial operation of this fi xture, a light smoke or smell may emit from the interior of the fi xture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp and will decrease gradually over time.
• Consistent operational breaks will ensure fi xture will function properly for many years.
• ONLY Use original packaging and materials to transport the fi xture in for service.
• It is strongly recommended to power the fixture down completely when not in use. Doing so will reduce wear on the fixture due to sustained or extended operational periods, therby maximizing its operational lifespan.

OVERVIEW

INSTALLATION

FLAMMABLE MATERIAL WARNING
Keep fi xture minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.
ELECTRICAL CONNECTIONS

• A qualifi ed electrician should be used for all electrical connections and/or installations.
• MINIMUM DISTANCE TO OBJECTS/SURFACES IS 6.6 FEET (2 METERS).
• MINIMUM DISTANCE OF INFLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET (0.5 METER)

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

• Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
• Before rigging/mounting a single fi xture or multiple fi xtures to any metal truss/structure or placing the fi xture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certifi ed to safely hold the combined weight of the fi xture(s), clamps, cables, and accessories.
• Maximum fixture ambient operating temperature is 113°F (45°C). Do not use operate the fixture when ambient temperature exceeds this value!
• Fixture(s) should be installed in areas outside walking paths, seating areas, or areas were unauthorized personnel might reach the fi xture by hand.
• NEVER stand directly below the fi xture(s) when rigging, removing, or servicing.
• Overhead fi xture installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable.
• Allow approximately 60 minutes for the fi xture to cool down before servicing.

IP RATING
This device is IP65 rated. This means that the unit is dust-tight, and protected against low-pressure jets of water from any direction.

RIGGING
Overhead rigging requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the fixture, among other skills. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury.

CLAMP INSTALLATION
This fixture features a mounting point on the yoke for the attachment of a mounting clamp. There is also a safety cable loop located on the rear of the fixture near the display screen (see the illustration below). When mounting the fixture to a truss or any other suspended or overhead installation, be sure to secure an appropriately rated clamp (not included) to the yoke, and attach a separate SAFETY CABLE of the appropriate weight rating to the safety cable loop.

SAFETY CABLE
ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.

STAND MOUNTING
This unit can also be installed atop a tripod stand. Simply insert the threaded bolt on the top of the tripod stand through the hole in the top of the mounting yoke. Tighten the nut onto the threaded bolt to secure the mounted device in place.

CAUTION!

• MAKE SURE THAT THE TRIPOD LEGS AND ALL TELESCOPING ELEMENTS OF THE TRIPOD STAND ARE LOCKED IN PLACE BEFORE INSTALLING THE DEVICE ATOP THE STAND!
• POSITION THE TRIPOD STAND AND MOUNTED DEVICE ONLY ON FLAT, STABLE SURFACES! DEPLOY TRIPOD LEGS FULLY IN ORDER TO MAXIMIZE STABILITY!

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS
External sources of light beams from direct sunlight, lighting moving head fixtures, and lasers which are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ lighting fixtures can cause severe internal damage, including burning of optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, irises, shutters, motors, belts, wiring, discharge lamps, and LEDs. This issue is not unique to ADJ lighting fixtures, but rather it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guide-lines below can reduce the risk of any potential damage if followed. Contact ADJ Service for more details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING OR MOVING HEAD FIXTURES, AND LASERS DURING UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ACCESSORY INSTALLATION

FROST FILTER
In order to install the included frost filter, simply align the four (4) holes on the frost filter with the four (4) holes located around the edge of the lens on the fixture. Insert a screw into each holes and tighten to secure the frost filter in place. Refer to the illustration below.

REMOTE DEVICE MANAGEMENT (RDM)
NOTE: In order for RDM to work properly, RDM enabled equipment must be used throughout the entire system, including DMX data splitters and wireless systems.

• Remote Device Management (RDM) is a protocol that sits on top of the DMX512 data standard for lighting, allowing the DMX systems of the fixtures to be modified and monitored remotely. This protocol is ideal for instances in which a unit is installed in a location that is not easily accessible.
• With RDM, the DMX512 system becomes bi-directional, allowing a compatible RDM enabled controller to send out a signal to devices on the wire, as well as allowing the fixture to respond (known as a GET command). The controller can then use its SET command to modify settings that would typically have to be changed or viewed directly via the unit’s display screen, including the DMX Address, DMX Channel Mode, and Temperature Sensors.
• Please be aware that not all RDM devices support all RDM features, and therefore it is important to check beforehand to ensure that the equipment that you are considering includes all of the features that you require.
• The following parameters are accessible in RDM on this device:

MANUFACTURER

MANUFACTURER ID
DEVICE ID
MODEL ID
DMX START ADDRESS
DMX PERSONALITY
DMX SLOTS
SOFTWARE VERSION

CONTROL PANEL

The fixture includes an easy to navigate system menu control panel display where all necessary settings and adjustments are made. (See image below)

• MODE: Cycles through the main menu options and/or return to previous menu without making changes.
• DOWN/UP: Scroll through options in the selected menu.
• ENTER: Select highlighted option and/or confirm selection.

DISPLAY LOCK

• This device features two different settings for locking the keypad. Setting Lock to “ON” requires the user to simply press and hold the MODE button for 10 seconds to unlock the keypad.
• Setting Lock to “ON1” provides an additional safeguard against accidental unlocking by requiring a passcode to unlock the device. To unlock, press the MODE button so that “LOCKED *****” is displayed on the screen, then press UP DOWN UP DOWN
• ENTER in that particular order. Each buttonpress will remove one asterisk from the LOCKED text on the display screen.

SOFTWARE UPDATES
For latest software and updating procedure, please contact ADJ Service.

SYSTEM MENU

DMX SET

| Address| 001 – 512| Set the DMX address of the unit.
---|---|---|---

Ch. Mode

| 4ch|

Set DMX channel mode.

7ch
8ch
10ch
13ch
16ch

No DMX

| Hold| The unit holds the last setting if the DMX signal is lost.
Blackout| The unit goes to standby mode if the DMX signal is lost.

Int. Prog

| Unit default to last internal program when DMX signal is lost.

FUNCTION

| Primary| On / Off| Set primary mode.
Secondary| On / Off| Set secondary mode.

Dim Mode

| Standard|
Stage|
TV|
Archi.|
Theatre|
Stage 2|
Dim Speed| 0.1s – 10s|
LED Refresh| 900, 1000, 1100, 1200, 1300, 1400, 1500, 2500,

4000, 5000, 10k, 15k, 20k, 25k

| Set LED refresh rate, default

= 1200 Hz

Dim Curve

| Square|
Linear|
Inv. Squa|
S. Curve|

Display

| SaveDelay| 1 – 10| Amount of time w/o activity before the screen powers off

Lock

| ON| Press MODE for 10s to unlock

ON1

| Press MODE and the display shows LOCKED *****. To unlock, press UP DOWN ENTER
OFF| Keypad is unlocked
CONTINUED ON THE NEXT PAGE

FUNCTION

(continued)

|

Service

|

Passcode = 050

|

Calibrate

| Red 000 – 255|
---|---|---|---|---|---
Green 000 – 255|
Blue 000 – 255|
Lime 000 – 255|
S. Update| Yes / No| Update software.
Restore: Passcode = 011| Yes / No| Restore the unit to factory settings.

MANUAL

| Red| 000 – 255| Manually adjust red
Blue| 000 – 255| Manually adjust blue
Green| 000 – 255| Manually adjust green
Lime| 000 – 255| Manually adjust lime
ClrMacro| 00 – 64| Select built-in color macro.
ClrTemp| 000 – 255| Set the color temperature.
ClrTeMac| 000 – 255| Select built-in color tem- perature pre-set macro.
Strobe| 000 – 255| Manually adjust strobing.
MastrDim| 000 – 255| Master dimmer.
AutoProg| 000 – 255| Select automatic program.
ProgSpd| 000 – 255| Set program speed.
ProgFade| 000 – 255| Set program fade.

PROGRAMS

|

Prog 0

| Speed| 000 – 255|
Fade| 000 – 255|

Prog 1

| Speed| 000 – 255|
Fade| 000 – 255|
…| …| …|

Prog 7

| Speed| 000 – 255|
Fade| 000 – 255|

INFO

|

Hours

|

PwrOnHr1

|

X Hrs

| Total hours that fixture has been powered on. Non- resettable.
PwrOnHr2| X Hrs| Hours that fixture has been powered on since the last reset.
PwrOnRst| Passcode = 050| Reset hours to zero.

Temp.

| xxx°| xxx F / xxx C| Units for temp. readout
MaxTemp1| xxx F / xxx C| Max temp since last reset.
MaxTemp2| xxx F / xxx C| All-time max temp, nonresettable.
TempRst.| Yes / No| Passcode = 050| Reset LED temp.

CONTINUED ON THE NEXT PAGE

INFO (continued)

|

DMX Values

| Red|

Displays current DMX values for each DMX channel.

---|---|---|---
Green
…
AutoProg
SoftVers| x.xx| Displays current software version.

DMX SETUP
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be linked together and operate from a single controller, as long as all fi xtures and the controller are DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible when using several DMX fixtures. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The Encore LP5IP can be controlled via DMX-512 protocol, and features multiple DMX channel modes. Your unit and your DMX controller require a 5-pin XLR connector for data input and data output. If you are making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro lighting stores). Your cables should be made with a male XLR connector at one end and a female XLR connector at the other. Also remember that DMX cable must be daisy chained and cannot be split.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

DMX ADDRESSING

• All fixtures should be given a DMX starting address when operating with a DMX controller, in order to ensure that the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control signal sent out from the DMX controller. The assignment of this starting DMX address is achieved by setting the correct DMX address on the digital control display on the fixture.
• You can set the same starting address for all fixtures or a group of fixtures, or set different addresses for each individual fixture. Setting all fixtures to the same DMX address will cause all fixtures to react in the same way. In this case, please note that changing the settings of one channel will affect all the fixtures simultaneously.
• If you set each fixture to a different DMX address, each unit will start to “listen” to the channel number you have set, based on the quantity of DMX channels of each fixture. That means changing the settings of one channel will only affect the selected fixture.
• As an example, when operating this device in 4 channel mode, you should set the starting DMX address of the first unit to 1, the second unit to 5 (1 + 4), the third unit to 9 (1 + 4 + 4), and so on. (See the chart below for more details.)

Channel Mode| Unit 1 Address| Unit 2 Address| Unit 3 Address| Unit 4 Address
---|---|---|---|---
4 Channels| 1| 5| 9| 13
7 Channels| 1| 8| 15| 22
8 Channels| 1| 9| 17| 25
10 Channels| 1| 11| 21| 31
13 Channels| 1| 14| 27| 40
16 Channels| 1| 17| 33| 49

DMX TRAITS

CHANNEL|

DMX VALUE

|

FUNCTION

---|---|---
4CH| 7CH| 8CH| 10CH| 13CH| 16CH
1| 1| 1| 1| 1| 1| 000 – 255| Red, 0% – 100%
| | 2| | | | 000 – 255| Red Fine
2| 2| 3| 2| 2| 2| 000 – 255| Green, 0% – 100%
| | 4| | | | 000 – 255| Green Fine
3| 3| 5| 3| 3| 3| 000 – 255| Blue, 0% – 100%
| | 6| | | | 000 – 255| Blue Fine
4| 4| 7| 4| 4| 4| 000 – 255| Lime, 0% – 100%
| | 8| | | | 000 – 255| Lime Fine
| | | 5| 5| 5| 000 – 255| Color Macros, see Color Macros Chart section for de- tailed information
| | | 6| 6| 6| 000 – 255| Color Temperature, 2700K – 7000K Linear
| | |

7

|

7

|

7

| | Color Temperature Macros
000| Off
001 – 054| 2700K
055 – 109| 3200K
110 – 164| 4000K
165 – 219| 5600K
220 – 255| 6500K
|

5

| |

8

|

8

|

8

| | Shutter, Strobe
000 – 031| LEDs Off
032 – 063| LEDs On
064 – 095| Strobe effect, slow to fast
096 – 127| LEDs On
128 – 159| Pulse-effect in sequences
160 – 191| LEDs On
192 – 223| Random strobe effect, slow to fast
224 – 255| LEDs On
| 6| | 9| 9| 9| 000 – 255| Dimmer Intensity, 0% – 100%
| 7| | 10| 10| 10| 000 – 255| Dimmer Fine
| | | | |

11

| | Auto Programs
000 – 031| Off
032 – 063| Auto Program 1
064 – 095| Auto Program 2
096 – 127| Auto Program 3
128 – 159| Auto Program 4

CONTINUED ON THE NEXT PAGE

CHANNEL|

DMX VALUE

|

FUNCTION

---|---|---
4CH| 7CH| 8CH| 10CH| 13CH| 16CH
| | | | |

11

| | Auto Programs (continued)
160 – 191| Auto Program 5
192 – 223| Auto Program 6
224 – 255| Auto Program 7
| | | | | 12| 000 – 255| Auto Program Speed, slow to fast
| | | | | 13| 000 – 255| Auto Program Fade, least to most
| | | |

11

|

14

| | Dim Mode
000 – 020| Default to the unit setting
021 – 040| Standard
041 – 060| Stage
061 – 080| TV
081 – 100| Architectural
101 – 120| Theatre
121 – 140| Stage 2
141| 0.1s dim speed
142| 0.2s dim speed
143| 0.3s dim speed
144| 0.4s dim speed
145| 0.5s dim speed
146| 10.6s dim speed
147| 0.7s dim speed
148| 0.8s dim speed
149| 0.9s dim speed
150| 1.0s dim speed
151| 1.5s dim speed
152| 2.0s dim speed
153| 3.0s dim speed
154| 4.0s dim speed
155| 5.0s dim speed
156| 6.0s dim speed
157| 7.0s dim speed
158| 8.0s dim speed
159| 9.0s dim speed
160| 10.0s dim speed
161 – 255| Default to the unit setting

CONTINUED ON THE NEXT PAGE

CHANNEL|

DMX VALUE

|

FUNCTION

---|---|---
4CH| 7CH| 8CH| 10CH| 13CH| 16CH
| | | |

12

|

15

| | Dim Curves
000 – 020| Square
021 – 040| Linear
041 – 060| Inv. Squa
061 – 080| S. Curve
081 – 255| No function
| | | |

13

|

16

| | Special Functions
000 – 015| Default to Unit Setting
016 – 030| 900 Hz
031 – 045| 1000 Hz
046 – 060| 1100 Hz
061 – 075| 1200 Hz
076 – 090| 1300 Hz
091 – 105| 1400 Hz
106 – 120| 1500 Hz
121 – 135| 2500 Hz
136 – 150| 4000 Hz
151 – 165| 5000 Hz
166 – 180| 10000 Hz
181 – 195| 15000 Hz
196 – 210| 20000 Hz
211 – 225| 25000 Hz
226-255| No Function

COLOR MACROS CHART

COLOR MACRO NO.| DMX VALUE| RED| GREEN| BLUE| LIME
---|---|---|---|---|---
Off| 000| 0| 0| 0| 0
1| 001 – 004| 80| 255| 234| 80
2| 005 – 008| 80| 255| 164| 80
3| 009 – 012| 77| 255| 112| 77
4| 013 – 016| 117| 255| 83| 83
5| 017 – 020| 160| 255| 77| 77
6| 021 – 024| 223| 255| 83| 83
7| 025 – 028| 255| 243| 77| 77
8| 029 – 032| 255| 200| 74| 74
9| 033 – 036| 255| 166| 77| 77
10| 037 – 040| 255| 125| 74| 74
11| 041 – 044| 255| 97| 77| 74
12| 045 – 048| 255| 71| 77| 71
13| 049 – 052| 255| 83| 134| 83
14| 053 – 056| 255| 93| 182| 93
15| 057 – 060| 255| 96| 236| 96
16| 061 – 064| 238| 93| 255| 93
17| 065 – 068| 196| 87| 255| 87
18| 069 – 072| 150| 90| 255| 90
19| 073 – 076| 100| 77| 255| 77
20| 077 – 080| 77| 100| 255| 77
21| 081 – 084| 67| 148| 255| 67
22| 085 – 088| 77| 195| 255| 77
23| 089 – 092| 77| 234| 255| 77
24| 093 – 096| 158| 255| 144| 144
25| 097 – 100| 255| 251| 153| 153
26| 101 – 104| 255| 175| 147| 147
27| 105 – 108| 255| 138| 186| 138
28| 109 – 112| 255| 147| 251| 147
29| 113 – 116| 151| 138| 255| 138
30| 117 – 120| 99| 0| 255| 100
31| 121 – 124| 138| 169| 255| 138
32| 125 – 128| 255| 255| 255| 255
33| 129 – 132| 255| 206| 143| 0
34| 133 – 136| 254| 177| 153| 0
35| 137 – 140| 254| 192| 138| 0
36| 141 – 144| 254| 165| 98| 0
COLOR MACRO NO.| DMX VALUE| RED| GREEN| BLUE| LIME
---|---|---|---|---|---
37| 145 – 148| 254| 121| 0| 0
38| 149 – 152| 176| 17| 0| 0
39| 153 – 156| 96| 0| 11| 0
40| 157 – 160| 234| 139| 171| 0
41| 161 – 164| 224| 5| 97| 0
42| 165 – 168| 175| 77| 173| 0
43| 169 – 172| 119| 130| 199| 0
44| 173 – 176| 147| 164| 212| 0
45| 177 – 180| 88| 2| 163| 0
46| 181 – 184| 0| 38| 86| 0
47| 185 – 188| 0| 142| 208| 0
48| 189 – 192| 52| 148| 209| 0
49| 193 – 196| 1| 134| 201| 0
50| 197 – 200| 0| 145| 212| 0
51| 201 – 204| 0| 121| 192| 0
52| 205 – 208| 0| 129| 184| 0
53| 209 – 212| 0| 83| 115| 0
54| 213 – 216| 0| 97| 166| 0
55| 217 – 220| 1| 100| 167| 0
56| 221 – 224| 0| 40| 86| 0
57| 225 – 228| 209| 219| 182| 0
58| 229 – 232| 42| 165| 85| 0
59| 233 – 236| 0| 46| 35| 0
60| 237 – 240| 8| 107| 222| 0
61| 241 – 244| 255| 0| 0| 0
62| 245 – 248| 0| 255| 0| 0
63| 249 – 252| 0| 0| 255| 0
64| 253 – 255| 0| 0| 0| 255

DIM MODES

DAISY CHAIN POWER LINKING

• These units have the capability to be daisy chained together via the power in/out ports. The maximum number of units that can be linked together in this manner is as follows:
• 21 units maximum when running on 110V power.
• 44 units maximum when running on 240V power.
• DO NOT EXCEED THE NUMBER OF UNITS LISTED ABOVE.
• DO NOT MIX MAKE AND MODEL TYPES WHEN DAISY CHAINING! All units that are connected in this manner must be of the same make and model type.

CLEANING AND MAINTENANCE

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING
Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fi xture operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fi xture’s optics. Clean the external lens surface periodically with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this fi xture. Please refer all other service issues to an authorized ADJ service technician. Should you need any spare parts, please order genuine parts from your local ADJ dealer.

Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
• Check for any deformations on the housing, color lenses, rigging hardware, and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust or liquids to enter into the fi xture. Damaged rigging points or unsecured rigging could cause fi xture to fall and seriously injure a person(s).
• Electric power supply cables must not show any damage, material fatigue, or sediments.
• NEVER remove the ground prong from the power cable.

DIMENSIONAL DRAWINGS

SPECIFICATIONS

SOURCE:

• Light Source: 5 x 20-Watt Quad RGBL LEDs (4-IN-1: Red, Green, Blue & Lime)

PHOTOMETRIC DATA

High CRI Data

• Beam Angle: 9.7°
• Field Angle: 18.8°
• CRI: 83
• CRI R9: 54
• Color Temperature: 6942K
• Lux: 2179 @ 3M, 785 @ 5M
• Lumens: 771

Full ON Data

• Beam angle: 9.6°
• Field Angle: 18.8°
• CRI: 67
• CRI R9: -98
• Color Temperature: 21188K
• Lux: 1766 @ 3M, 636 @ 5M
• Lumens: 607

EFFECTS

• Linear Color Temperature Control (2700K to 7000K)
• Preset Color Temperatures (2700K, 3200K, 4000K, 5600K and 6500K)
• 16-Bit Fine Color Control (Red, Green, Blue & Lime)
• 64 built-in Color Macros

CONTROL / CONNECTIONS

• 4-button, DMX digital display on rear panel
• 5 Operational modes: Static Color Mode, RGBL Dimmer Mode, Program Mode, and DMX Controlled
• Supports RDM (Remote Device Management)
• With Wired Digital Communication Network
• 6 selectable Dimming Modes (Standard, Stage, TV, Architectural, Theatre & Stage 2)
• 4 selectable Dim Curves (Linear, Square, Inv. Squa, S-Curve)
• Adjustable Refresh Rate (14 presets from 900 – 25,000Hz)
• Flicker Free operation (No flickering on camera)
• LED pulse and strobe effect
• Electronic Dimming: 0 – 100%
• 6 DMX Modes: 4, 7, 8, 10, 13, & 16-channel
• Quiet fan mode

CONSTRUCTION

• IP65 Rated: Ingress Protection against liquid, snow, dust and sand
• All metal construction
• IP Rated rubber covers protect In/Out Locking Power connectors and IP rated 5-pin sockets
• Locking, outdoor IN/Out Power connectors
• Data linkable via 5-pin XLR DMX connections
• Scissor Yoke & safety eye

ELECTRICAL / THERMAL

• Multi-voltage operation: AC 100-240V, 47/63Hz
• Daisy chain: 21 units max (110V) / 44 units max (240v)
• Max power: 32W

DIMENSIONS / WEIGHT

• Dimensions (LxWxH): 5.9”x8.2”x10.1” / 150.6mm x 209.0mm x 255.0mm
• Weight: 5.3 lbs / 2.4 kgs

APPROVALS / RATINGS

• cETLus (Control #4010765)
• IP65

Specifications and manual are subject to improvement without prior written notice.

ACCESSORY AND ORDERING INFORMATION

References

• Topics | ADJ Forums
• ADJ Product Parts - Lighting Online Parts Store
• Home
• ADJ Partsshop - Service is our passion!
• ADJ Supply Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>