FOXSUR FBT200 24V Smart Battery Tester User Manual

12V 24V
SMART BATTERY TESTER

USER MANUAL

Welcome

Thank you for purchasing Battery Tester. Please patiently read and understand this use manual before operating this product. if you have any questions or issues, please contact our technical support

About

Applying the most advanced conductance testing technology, and the reverse polarity protection etc., FBT server as a 12V-24V battery tester to provide technicians with critical information about battery health status, to find battery and charging problems  quickly, easily and accurately.

Package Contents

1. Battery Tester
2. User Manual

Compatibility
Please be noted that battery type and CCA values(Cold Cranking Amp) marked on the battery label, please refer to it before using.
Tester supports the following types.

1. VRLA/GEL/AGM/EFB/STD
2. Regular Flooded

Specifications

Display: 2.7″ LCD
Cable reach: 650mm (25.6 inches)
Storage Temperature: -20’C to +70’C (-4’F to 158’F)
Working Temperature: -20’C to +60’C (-4’F to 140’F)
Dimensions(LWH): 1509035mm(5.93.541.38 inch)
Weight: 325g(0.72lb)

Important

• Use this tester in accordance with there instructions, taking into account the working conditions and the work to be performed. Use of this tester for operations different from those intended could result in a hazardous situation
• Before testing, make sure the battery terminals are really clean as grease and dust could lead to errors in the test results.
• Wear eye protection when working around batteries.
• Check the insulation layer of the battery clamps is in normal condition(no damage, bareness or disconnection),in case of the electric shock.
• Test in a well-ventilated area. Explosive and toxic gases may be produced during testing
• Keep hair, hands,and clothing as well as tester leads and cords away from moving blades and belts.
• The tester is not a toy. keep it out of the reach of children.
• Do Not place the tester near the engine or exhaust pipe to avoid damaged by high temperatures, when the car engine is running.
• Do not smoke, cause sparks, or strike matches near the battery when testing
• Do not remove battery clamps while testing
• Do not put the tester into a highly humid, dusty environment.
• Do not disassemble the tester, or may cause damage.

Operation Introduction

| Previous item, or increase the battery rating values
**** 2|

| Cancel
3|

| Next item, or decrease the battery rating values
4| | Confirm; Enter and proceed
5| | Reset / Restart
**** 6|

Red Clamp

| Positive battery test clamp
7|

Black Clamp

| **** Negative battery test clamp

How to Use

Tester will test each battery according to the selected actual system standard and rating marked on the battery, to get the accurate results.

1. Before Test
   the engine and all other accessory loads must be OFF during test in order to have accurate results, Turn on the vehicle headlamps for 2-3 minutes until the battery voltage drops back to normal value if the battery is just fully charged.

2. Steps
   a. The Red(+) Positive Battery clamp is connected to the (+)positive battery terminal, and the BLACK(-) Negative Battery Clamp is connected to the (-) negative battery terminal. Ensure that the clamps have a firm, secure grip on the battery terminals for  accurate results.
   b. Press the or to select the “Battery Type” (specified on the battery rating label), then press “ENTER” to continue.
   C. Press the or to select the Correct testing standard (specified on the battery rating label), then Press “ENTER” to continue.
   D. Hold the or to select the battery EDC/CCA values(specified on the battery rating label or Refer to the EDC/CCA Parameters Table)
   EDC/CCA Parameters Table

   ---

No| Battery Size| EDC Value| No
18| Battery Size| EDC Value
---|---|---|---|---|---
1| 3.3AH| 55A| 28AH| 340A
2| 4AH| 65A| 19| 31AH| 350A
3| 5AH| 80A| 20| 33AH| 360A
4| 6AH| 100A| 21| 38AH| 370A
5| 7AH| 130A| 22| 40AH| 380A
6| 8AH| 150A| 23| 45AH| 400A
7| 9AH| 155A| 24| 50AH| 425A
8| 10AH| 160A| 25| 55AH| 445A
9| 12AH| 210A| 26| 60AH| 465A
10| 14AH| 220A| 27| 65AH| 520A
11| 15AH| 230A| 28| 75AH| 550A
12| 17AH| 250A| 29| 80AH| 570A
13| 18AH| 265A| 30| 85AH| 600A
14| 20AH| 285A| 31| 100AH| 670A
15| 24AH| 310A| 32| 120AH| 700A
16| 25AH| 320A| 33| 150AH| 755A
17| 26AH| 330A| 34| 200AH| 995A

E. Press “ENTER” to start the battery test.
F. The test results is as Follows:
SOH: State of Health I.R: Internal Resistance
SOC: State of Charge
VOLT: Battery Voltage
EDC/CCA: Estimated Discharge Current

Test Results Description

Battery System Standard Description
The battery tester analyzer will test each battery according to the selected system and rating.

CCA:| Cold Cranking Amps, specified by SAE & BCI, most frequently used value for starting battery at 0’F (-18’C)
---|---
IEC:| Internal Electro Technical Commission Standard
SAE:| Society of Automotive Engineers Standard
EN:| European Automobile Industry Association Standard
DIN:| German Auto Industry Committee Standard
CA:| Cranking Amps Standard, effective starting current value at 0’C

FAQ

Q: Does this battery tester have power?

A: No, it can only be powered by the tested battery.

Q: Can Tester Charge the Battery?

A: No, it will not charge any batteries, But it can detect the battery.

Q: Can Tester get the battery life?

A: Yes, it will give you the health of the battery and a charge percentage.

Q: What batteries can the Tester be used on?

A: it can be used on 12V and 24V batteries.

Q: Why is the result of the Tester test inaccurate?

A: Maybe the parameter you set is wrong. Please input the correct data from the battery label.

Q: Why nothing is displayed?

A: Please make sure your battery voltage is higher than 8V and The positive and negative clamp are connected correctly

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>