FOXSUR FBC1207D 12V 7A 7-stage Battery Charger User Manual
- June 6, 2024
- FOXSUR
Table of Contents
FOXSUR FBC1207D 12V 7A 7-stage Battery Charger
Please read this manual and follow the instructions carefully before using.
WARNING:
- The FBC1207D charger is designed for 12V batteries with capacity from 6AH – 120AH.
- Check battery manufacturer specifications before using.
- Explosive gases may emitting from battery during charging. Provide ventilation to prevent flames and sparks.
- Do not expose charger to the sun, or under high temperature environment.
- Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin or eyes.
- Do not charge a frozen or damaged battery.
- Do not charge non-rechargeable batteries.
- Do not place the charger on the battery while charging.
- Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short-circuit battery or other electrical part that may cause explosion.
- When working with a lead-acid battery, remove personal metal items such as rings, bracelets, necklaces, watch…
- Do not smoke or allow a spark or flame while charging.
- In order to reduce risk of electric shock, unplug charger from AC outlet before doing any maintenance or cleaning.
- Not for use by children or by anyone who is unable to follow instructions of this manual, unless they are supervised by an adult to ensure the proper use of charger.
MAIN FEATURES:
- High efficiency (>85%).
- GEL, Standard, AGM, MOTO battery type can selectable
- The 7-stage microprocessor-controlled charging process provides the best possible application and enables efficient battery charging.
- Charging voltage adapts to temperature, that can prevent over- or under- charging of battery.
- Capable of recharging severely discharged or heavily sulfated battery.
- Reverse polarity protection, short circuit protection, over-charge protections, parks free contact.
- LCD display: voltage, current, temperature etc.
- Ease of use. Clear charging status display.
- Full microprocessor controlled.
- Do not over-charge your battery even it is kept connecting in any mode.
LCD DISPLAY
- stage: Battery desulphation
- stage: Soft start charging
- stage: Bulk charging
- stage: Absorption charging
- stage: Battery test
- stage: Recondition charging
- stage: Float & maintenance charging
CHARGER MODES
GEL| GEL Batteries Mode
For charging GEL Batteries
---|---
STANDA RD| Standard Batteries Mode
For SLA, WET, DEEP CYCLE, EFB, Calcium Batteries
AGM| Standard Batteries Mode For charging AGM batteries
MOTO| Motorcycle Batteries Mode For charging motorcycle batteries
REPAIR
| Repair Mode (16 hours)
An advanced battery recovery mode for repairing and storing, old, idle, damaged, stratified or sulfated.
Not all batteries can be recovered, only can use on Motorcycle and Car batteries
MODE
| Charge Mode Select Button
After charging for 30 seconds, the mode button will be locked. If you want to use it again, need to remove the alligator clip from the battery
CONNECT TO THE BATTERY
Do not connect the AC power plug until all other connections are made. Identify the correct polarity of the battery terminals on the battery. Do not make any connections to the carburetor, fuel lines, or thin, sheet metal parts. The below instructions are for a negative ground system (most common). If your vehicle is a positive ground system (very uncommon), follow the below instructions in reverse order.
- Connect the positive (red) clamp to the positive (POS, P, +) battery terminal.
- Connect the negative (black) clamp to the negative (NEG, N, -) battery terminal.
- Connect the battery charger into a suitable electrical outlet. Do not face the battery when making this connection.
- When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive ground systems).
BEGIN CHARGING
- Verify the voltage and chemistry of the battery.
- Confirm that you have connected the battery clamps or eyelet terminal connectors properly and the AC power plug is plugged into an electrical outlet.
- Press the mode button to toggle to the appropriate charge mode.
- The mode LED will illuminate the selected charge mode and the Charge Icon will illuminate (depending on the health of the battery) indicating the charging process has started.
- The charger can now be left connected to the battery at all times to provide maintenance charging.
Auto-Memory: The charger has built in auto-memory and will return to the last charge mode when connected.
TECHNICAL SPECIFICATIONS
Model | FBC1207D |
---|---|
Type | Smart & Automatic |
AC Input | 100 – 240V 50/60HZ |
Output Voltage | 12V |
Output Current | 7A max. |
Minimum Start Volt | Battery Voltage >7.0V |
Input Power With Load | Max. 105W |
Input Power under No Load | 2.6W |
Cooling | Fan |
Size (LWH) | 1508663mm |
Net Weight | 415g |
Approval | CE / FCC |
Battery Charger
- Model FBC1207D
- Input 100-240V-50/60HZ, max. 105W
- Output DC 12V max.7A
- Manufacturer Foxsur Electronic Equipment Co., Ltd.
- Address Hengjiangxia Industrial Zone, ChangPin Tower, DongGuan City, GuangDong Province, China
BellaCocool GmbH
PettenkoferstraBe 18,10247 Berlin, Germany
E-mail:info@bellacocool.de Tel: +49 30/98578681
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>