sensorswitch sPODMA D SPODMA BAA Wall Switch Instruction Manual

: June 12, 2024
: sensorswitch

Table of Contents

OVERVIEW
FEATURES
TYPICAL CONFIGURATIONS
PROGRAMMING INSTRUCTIONS
SPECIFICATIONS
Documents / Resources

sPODMA BAA
Wall Switch sPODMA D

OVERVIEW

The Push-Button Wall Switch sPODMA BAA Series of low voltage wall stations interface with standard Sensor Switch occupancy sensors and power packs in order to implement a wide range of single and bi-level switching applications. These switch devices provide an elegant and cost effective way of deploying bi-level lighting control that meet energy and building codes without having to source special sensors or power packs.

FEATURES

Enables Standard Occupancy Sensors to be used for Manual On Operation
Alternative Usage as Override Switch for Auto-On Applications
Single Gang Decorator Style w/ either 1 or 2 On/Off Switches
Soft-Click Push-Buttons
Programmable w/o Removing Switch Plate
Optional Dual Manual On Operation
Optional Multi-way Operation
Optional 0-10 VDC Dimming Control
Auto return to last set level – on dimmable devices, returns to last set dim level before switched off

Buy American Act (BAA)
This product is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT regulations.
Please refer to www.acuitybrands.com/buy- american for additional information.
Warranty
Five-year limited warranty. This is the only warranty provided and no other statements in this specification sheet create any warranty of any kind. All other express and implied warranties are disclaimed. Complete warranty terms located at: www.acuitybrands.com/support/warranty/terms-and- conditions
Note: Actual performance may differ as a result of end-user environment and application. Specifications subject to change without notice.
ORDERING INFORMATION

Notes
1 BAA variants may experience extended Lead-Times.

TYPICAL CONFIGURATIONS

(NOTE: 18 AWG wire is recommended for all wiring) Note: If sensor also has dimming output (e.g., CM 9 ADC), connect sensor VIO wire to SPODMA and ballast/driver VIO wire. Lowest output level always takes precedence. If no sensor is used, connect the SPODMA white wire to the red wires. 3-WAY MANUAL ON SOLUTION w/ OCCUPANCY SENSOR

Note 1: SPODMA (SA) 3X D units should only be used in multi-way applications with SPODMA (SA) 3X units (non-dimming)as dimming levels are not communicated between devices.
Note 2: For multi-way configurations greater than two units, connect additional unit(s) in same manner as bottom right SPODMA SA 3X unit in diagram above.
Note 3: If no sensor is used, connect the SPODMA white wire to the red wires.

PROGRAMMING INSTRUCTIONS

(Please read all 7 steps before programming)

Enter programming mode by pressing & holding upper most button until LED flashes rapidly. Release button.
Enter the On Mode function by pressing button twice.
The current On Mode setting will then be fed out in a sequence of LED flashes as indicated in the table below (e.g., one flash for Auto-On). To change the setting, proceed to step 4 before sequence repeats 10 times.
At any time while the switch is flashing back the current On Mode setting, interrupt it by pressing button the number of times for the new desired On Mode setting as indicated in the table below (e.g., press twice for Manual On). Switch will begin to flash back new setting as confirmation.
Next, while the switch is flashing back new setting, interrupt it by pressing and holding button until LED flashes rapidly. Release button.
As final confirmation and activation of the new setting, press button two times.
LED will flash twice indicating acceptance of new setting. If two flashes are not seen, repeat 7 step process.

Note: To exit programming mode without saving, wait for blink back sequence to repeat 10 times then return to step 1.

Function Number| Function Name| Settings (see ordering block for defaults)
---|---|---
Setting Number| Pole 1
2| On Mode| 1| Auto-On
2| Manual On

SPECIFICATIONS

Electrical	Input Ratings	12-24VACNDC, 5mA
Output Ratings	Sinks <20mA

Acuity Brands | One Lithonia Way Conyers, GA 30012
Phone: 800.535.2465 “
www.acuitybrands.com/sensorswitch
© 2021-2023 Acuity Brands Lighting, Inc.
All rights reserved. Rev. 02/06/23
SPODMA BAA

Documents / Resources

| sensorswitch sPODMA D SPODMA BAA Wall Switch [pdf] Instruction Manual
sPODMA D BAA, sPODMA SA D, sPODMA D SPODMA BAA Wall Switch, sPODMA D Wall Switch, SPODMA BAA Wall Switch, Wall Switch, Switch
---|---