SHUTTLE EN01 Series Intelligent Edge Computer User Manual

: June 12, 2024
: Shuttle

Table of Contents

SHUTTLE EN01 Series Intelligent Edge Computer
**Product Usage Instructions
Safety Information
Driver and Software Installation
Appendix
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SHUTTLE EN01 Series Intelligent Edge Computer

Product Information

Product Name	EN01 Series XPC
Trademark	Shuttle is a registered trademark of Shuttle Inc.
Compliance	This device complies to Part 15 of the FCC Rules.
Operating Conditions	This device must withstand any background interference

including those that may cause undesired operation.
Safety Information| Read the following precautions before setting up:

Incorrectly replacing the battery may damage this computer.
Replace only with the same or equivalent type recommended by the
manufacturer. Disposal of used batteries according to the
manufacturer’s instructions.
Do not place this device underneath heavy loads or in an unstable
position.
Do not expose this device to high levels of direct sunlight, high
humidity, or wet conditions.
Do not use or expose this device around magnetic fields as
magnetic interference may affect the performance of the
device.
Do not block the air vents to this device or impede the airflow
in any way.

**Product Usage Instructions

**

Driver and Software Installation

Insert the Motherboard Driver DVD into your computer’s DVD drive.
The DVD will auto-install the necessary drivers and utilities for the motherboard.

Capture Card Codecs/Driver/Tool Installation

Insert the Capture Card Codecs/Driver/Tool DVD into your computer’s DVD drive.
The DVD will install the necessary codecs, driver, and tool for the capture card.

User Manuals

Insert the User Manuals DVD into your computer’s DVD drive.
The DVD will allow you to install Adobe Reader 9.5 and access the Motherboard Manual and Quick Guide.

Starting BIOS
To enter the BIOS setup screens, follow these steps:

Power on the motherboard.
Press the ‘DEL’ key on your keyboard when you see the following text prompt: “Press DEL to run Setup”.
After pressing the ‘DEL’ key, the main BIOS setup menu will display. From here, you can access other setup screens such as the Chipset and Power menus.

Shuttle®
XPC Installation Guide
Copyright
©2019 by Shuttle® Inc. All Rights Reserved.
No part of this publication may be reproduced, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means such as electronic, mechanical, magnetic, optical, chemical, photocopy, manual, or otherwise, without prior written permission from Shuttle® Inc.
Other brands and product names used herein are for identification purposes only and may be trademarks of their respective owners.

Disclaimer
Shuttle® Inc. shall not be liable for any incidental or consequential damages resulting from the performance or use of this product.
Shuttle® Inc. makes no representation or warranty regarding the contents of this ma- nual. Information in this manual had been carefully checked for accuracy;however, no guarantee is given as to the correctness of the contents. For continuing product improvement, Shuttle® Inc. reserves the right to revise the manual or make changes to the specifications of this product at any time without notice and obligation to any person or entity regarding such change. The information contained in this manual is provided for general use by customers.
This device complies to Part 15 of the FCC Rules. Operation is subject to the follow-ing two conditions:

This device may not cause harmful interference.
This device must withstand any background interference including those that may cause undesired operation.

Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel and Pentium are registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.

General Notice
Other brand and product names used herein are for identification purposes only and may be trademarks of their respective owners.

Safety Information

Read the following precautions before setting up.

CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent type recommended by the manufacturer. Disposal of used batteries according to the manufacturer’s instructions.

Installation Notices
Do not place this device underneath heavy loads or in an unstable position.
Do not expose this device to high levels of direct sunlight, high-humidity or wet conditions.
Do not use or expose this device around magnetic fields as magnetic interference may affect the performance of the device.
Do not block the air vents to this device or impede the airflow in any way.

Driver and Software Installation

Motherboard Driver DVD
The DVD contents attached in EN01 Series motherboard are subject to change without notice.
The Motherboard Driver DVD contains all the motherboard drivers necessary to optimize the performance of this Shuttle Xvision in a Windows® OS. Install these
drivers after installing Microsoft® Windows®.
Insert the attached DVD into your DVD-ROM drive. The DVD AutoRun screen should appear. If the AutoRun screen does not appear, double click on Autorun icon in My Computer to bring up Shuttle Mainboard Software Setup screen.
Navigation Bar Description :

Auto Install Driver/Utility.
Capture Card Codecs/Driver/Tool.
User Manuals – Motherboard Manual, Quick Guide.
Link To Shuttle Website – Link to shuttle website homepage.
Browse This DVD – Allows you to see contents of this DVD.

Capture Card Codecs/Driver/Tool

Install Capture Card Codecs
Install Cpature Card MZ0380 Driver
Install Capture Card Tool

User Manuals

Install Adobe Reader 9.5
MotherBoard Manual
Quick Guide

Appendix

Starting BIOS
AMIBIOS has been integrated into many motherboards for over a decade. In the past, people often referred to the AMIBIOS setup menu as BIOS, BIOS setup, or CMOS setup.
American Megatrends refers to this setup as BIOS. Specifically, it is the name of the AMIBIOS BIOS setup utility. This chapter describes the basic navigation of the BIOS setup screens.

Enter the BIOS
To enter the BIOS setup screens, follow the steps below:

Step1. Power on the motherboard.
Step2. Press the key on your keyboard when you see the following text prompt: Press DEL to run Setup.
Step3. After you press the key, the main BIOS setup menu displays.

You can access the other setup screens from the main BIOS setup menu, such as the Chipset and Power menus.
This manual describes the standard look of the BIOS setup screen.
The motherboard manufacturer has the ability to change any and all of the settings described in this manual. This means that some of the options described in this manual do not exist in your motherboard’s AMIBIOS.
In most cases, the key is used to invoke the BIOS setup screen. There are a few cases that other keys are used, such as ,, and so on.

BIOS Setup Menu
The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this user’s guide.
The Main BIOS setup menu screen has two main frames. The left frame displays all the options that can be configured. “Grayed-out” options cannot be configured. Options is blue can be.
The right frame displays the key legend. Above the key legend is an area reserved for a text message. When an option is selected in the left frame, it is highlighted in white.
Often a text message will accompany it.
AMIBIOS has default text messages built into it. The motherboard manufacture retains the option to include, leave out, or change any of these text messages. They can also add their own text messages. Because of this, many screen shots in this manual are different from your BIOS setup screen.
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include , , , ,

keys, and so on. There is a hot key legend located in the right frame on most BIOS setup screens.

Hot Key	Description

→ Left
← Right| The Left and Right keys allow you to select a BIOS setup screen. For example: Main screen, Advanced screen, Chipset screen, and so on.
↑ Up
↓ Down| The Up and Down keys allow you to select an BIOS setup item or sub- screen.
+- Plus/Minus| The Plus and Minus keys allow you to change the field value of a particular setup item. For example: Date and Time.
Tab| The key allows you to select BIOS setup fields.
F1| The key allows you to display the General Help screen. Press the key to open the General Help screen.
F4| The key allows you to save any changes you have made and exit BIOS Setup. Press the key to save your changes. Press the key to save the configuration and exit. You can also use the key to select Cancel and then press the key to abort this function and return to the previous screen.
ESC| The key allows you to discard any changes you have made and exit the BIOS Setup. Press the key to exit the BIOS setup without saving your changes. Press the key to discard changes and exit. You can also use the key to select Cancel and then press the key to abort this function and return to the previous screen.
Enter| The key allows you to display or change the setup option listed for a particular setup item. The key can also allow you to display the setup sub- screens.

Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below.

System Time/System Date
Use this option to change the system time and date. Highlight System Time or System Date using the keys. Enter new values through the keyboard. Press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format.
The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and 5:30 P.M. as 17:30:00.

Advanced
Select the Advanced tab from the BIOS setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item.
You can display an Advanced BIOS Setup option by highlighting it using the

keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screen is shown below. The sub menus are described on the following pages.

CPU Configuration
You can use this screen to select options for the CPU Configuration Settings. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown below.
The CPU Configuration setup screen varies depending on the installed processor.

EIST
This item allows you to enable or disable Enhanced lntel SpeedStep® Technology.

The choice: Enabled , Disabled.

Turbo Mode
This item allows you to enable or disable lntel® Turbo Boost Technology.

The choice: Enabled , Disabled.

The CPU Configuration setup screen varies depending on the installed processor.

C State Support
This item allows you to enable or disable CPU C State.

The choice: Enabled , Disabled.

Intel® V. T.
When enable, a VMM can utilize the additional hardware capabilities provided by vanderpool Technology.

The choice: Enabled , Disabled.

CPU support, item appear.

SATA Configuration

USB Configuration

Onboard Device Configuration

Onboard LAN Function
This item allows you to enable or disable LAN Function.

The choice: Enabled , Disabled.

Onboard LAN Boot ROM
This item allows you to enable or disable Onboard LAN Boot ROM.

The choice: Enabled , Disabled.
IGD Memory Size Select

Allows you to select the size of system memory used by the internal graphics device.

The choice: 64MB, 128MB, 256MB, 512MB.

M.2 Device Select
M.2 PCIE and SATA device selection.

The choice: PCIE , SATA.

Intel® VT-d
This item allows you to enable or disable Intel® VT-d.

The choice: Enabled , Disabled. Serial Port 4 Mode
COM mode select.
The choice: RS232, RS422, RS485.

Power Management Configuration

Wake Up By USB (S3)
This item allows you to enable or disable system wake up by USB (S3).

The choice: Enabled , Disabled.
Power-On after Power-Fail

This item allows you to set system power on automatically after AC power restored.

The choice: Power On, Former-sts, Power Off

Wake Up By LAN
This item allows you to enable or disable system wake on by onboard LAN chip.

The choice: Enabled , Disabled.

PowerOn by RTC Alarm
When enabled, System will wake on the hr::min::sec specified.

The choice: Enabled , Disabled.

TPM Configuration

Security Device Support
This item allows you to enable or disable fTPM.

The choice: Enabled , Disabled.

Hardware Health Configuration

Boot
Select the Boot tab from the BIOS setup screen to enter the Boot BIOS Setup screen. You can select any of the items in the left frame of the screen, such as Boot Settings Configuration, to go to the sub menu for that item.
You can display an Boot BIOS Setup option by highlighting it using the keys. All Boot BIOS Setup options are described in this section.
The Boot BIOS Setup screen is shown below. The sub menus are described on the following pages.

Bootup Num-Lock
Select NumLock state after system bootup.

The choice: Enabled , Disabled.

Fast Boot Function
This item allows you to enable or disable Fast Boot Function.

The choice: Enabled , Disabled.

Boot from USB device
Enabled/Disabled onboard USB storage boot function.

The choice: Enabled , Disabled.

Boot Device Priority (Boot Option #1/2/3/….)
Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu.

Security
Select the Security tab from the BIOS setup screen to enter the Security BIOS Setup screen. You can display an Security BIOS Setup option by highlighting it using the keys. All Security BIOS Setup options are described in this section.
The Security Setup screen is shown below. The sub menus are documented on the following pages.

Supervisor Password
Indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.

User Password
Indicates whether a user password has been set. If the password has been in- stalled, Installed displays. If not, Not Installed displays.

Change Supervisor Password
Select Change Supervisor Password from the Security Setup menu and press

.

Enter New Password:
Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes.

Change User Password
Select Change User Password from the Security Setup menu and press .

Enter New Password:
Type the password and press . The screen does not display the characters entered. Retype the password as prompted and press . If the password confirmation is incorrect, an error message appears. The password is stored in NVRAM after BIOS completes.

Password Login control
This item allows user to adjust Password Login control.

The choice: Setup, Boot, Both.

Flash Write Protection
Choose [Enabled] to avoid virus destroy BIOS. If you want to flash BIOS, you must set it [Disabled].

The choice: Enabled or Disabled.

Secure Boot Control
This item allows user to enable/disable Secure Boot function.

Exit
Select the Exit tab from the BIOS setup screen to enter the Exit BIOS Setup screen.
You can display an Exit BIOS Setup option by highlighting it using the keys. All Exit BIOS Setup options are described in this section.
The Exit BIOS Setup screen is shown below.

Save Changes and Exit
When you have completed the system configuration changes, select this option to leave BIOS Setup and reboot the computer so the new system configuration parameters can take effect.
Select “Save Changes and Exit” from the Exit menu and press .

Save Configuration Changes and Exit Now?
[Ok] [Cancel] appears in the window. Select Ok to save changes and exit.

Exit Without Saving Changes
Select “Exit without Saving Changes” from the Exit menu and press . Select Ok to discard changes and Exit.

Load Defaults Settings
BIOS automatically sets all BIOS Setup options to a complete set of default set-tings when you Select this option. The Optimal settings are designed for maxi-mum system performance, but may not work best for all computer applications. In particular, do not use the Optimal BIOS Setup options if your computer is ex-periencing system configuration problems.
Select Load Optimal Defaults from the Exit menu and press .
Select Ok to load optimal defaults.