STI-V34104 4-Channel Voice Receiver User Manual

: June 12, 2024
: STI

Table of Contents

HOW THE PRODUCT WORKS
BEFORE YOU START
ZONE PROGRAMMING PROCEDURES
Dip Switch Functions
PROGRAMMING
SCROLLING MESSAGE/TONES – Default messages by sensor type
ADVANCED DIP SWITCH MESSAGE CODES
DELETE SENSOR
LOW BATTERY / TAMPER / OUT OF RANGE ALERT
MOUNTING OPTIONS
WARRANTY INFORMATION
IMPORTANT NOTICE
TECHNICAL SUPPORT
[
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

STI-V34104 4-Channel Voice Receiver User Manual

HOW THE PRODUCT WORKS

The 4-Channel Voice Receiver is a multipurpose long-range receiver that works with a wide range of STI Wireless Alert Series sensors. Most products can achieve up to 1,000’ receiver range (line of site). Four zone indicators light up to indicate a sensor has triggered. Selectable tones and voice messages are a key feature. Sensors have default messages or program your own by choosing up to four words or tones from a preprogrammed list. All voice messages are available in English or Spanish. Receiver is intended for indoor use only.

BEFORE YOU START

Review detailed product specifications (Fig. 1 and 2)

ZONE PROGRAMMING PROCEDURES

Only receives wireless signals from the STI Wireless Alert Series products. Program up to 4 sensors or keyfobs. Does not allow programming into an occupied zone. Cannot program the same sensor into more than one zone. The unit will state, “Please change to normal mode if programming is completed.” (Repeats every 60 seconds.) Default language is English. Move dip switch 1 to the “on” (up) position for Spanish.

MODES OF OPERATION
Set at time of programming by zone
Zone Latching: Dip Switch #2 ‘OFF’
When sensor is triggered, red zone light is solid. “Latching” let’s you know a zone was triggered, but the alert has cleared (flashing red LED). To reset, push the acknowledge button.
Zone Auto Restore: Dip Switch #2 ‘ON’
“Auto-Restore” sounds when a zone has been triggered. Zone automatically restores to solid green light without pressing acknowledge button.

Dip Switch Functions

DIP SWITCH	NORMAL MODE	PROGRAM MODE
OFF (DOWN)	ON (UP)	OFF (DOWN)
1	—	ENGLISH*
2	—	LATCHING*
3	PRE-ALERT TONE*	NO TONE
4	—	TONE/WORD SELECT
5	—	TONE/WORD SELECT
6	—	TONE/WORD SELECT
7	—	TONE/WORD SELECT
8	—	TONE/WORD SELECT

Default Mode

PROGRAMMING

Plug in receiver.
Listen to verbal voice commands. They will guide you through programming.

Notes :

Firmly press acknowledge button at any time to stop voice.
Make sure battery is installed in sensor.
Each sensor provides an initial sound (DONG). (See CHART 2 below)
Each zone button, with programmed sensor, scrolls through default messages using the zone/message selection button.
Accept tone/message selected by moving switch to NORMAL mode. These can be changed at any time by moving the switch to PROGRAM and pushing the zone/message selection button.

SCROLLING MESSAGE/TONES – Default messages by sensor type

Universal Garage Sentry Mailbox Alert| Doorbell Button| Driveway Monitor| Entry Alert ®| Indoor and Outdoor PIR| Exit/Fire Extinguisher Stopper| Stopper Station Stopper Station Shield
---|---|---|---|---|---|---
Mailbox| Call| Front Driveway| Front Door Alert| Motion Front| Emergency Door Alert| Assistance
Door| Alert| Side Driveway| Side Door Alert| Motion Side| Front Extinguisher Alert| Alert
Gate| Assistance| Rear Driveway| Rear Door Alert| Motion Rear| Side Extinguisher Alert| Protective Cover
Window| Service| No Sound| Exit Door Alert| Motion Driveway| Rear Extinguisher Alert| No Sound
Cover| Door| Ding| Gate Alert| Motion Upstairs| Assistance| Ding
Garage Sentry| Customer| Ding Dong| Dock Alert| Motion Downstairs| Extinguisher| Ding Dong
Temperature| No Sound| Dong| No Sound| Customer| Side| Dong
Sump Pump| Ding| 4-Note Chime| Ding| Ding| Hall| 4-Note Chime
Freezer| Ding Dong| 8-Note Chime| Ding Dong| Ding Dong| No Sound| 8-Note Chime
Refrigerator| Dong| Knock| Dong| Dong| Ding| Knock
Water Level| 4-Note Chime| Bell| 4-Note Chime| 4-Note Chime| Ding Dong| Jingle Bells
No Sound| 8-Note Chime| Buzzer| 8-Note Chime| 8-Note Chime| Dong| Dogs Barking
Ding| Knock| | Knock| Knock| 4-Note Chime| Bell
Ding Dong| Jingle Bells| | Jingle Bells| Bell| 8-Note Chime| Buzzer
Dong| Dogs Barking| | Dogs Barking| Buzzer| Knock|
4-Note Chime| Bell| | Bell| | Jingle Bells|
8-Note Chime| Buzzer| | Buzzer| | Dogs Barking|
Knock| Bell
Jingle Bells| Buzzer
Dogs Barking
Bells
Buzzer

Zone light indicator still operates

ADVANCED PROGRAMMING FOR ALREADY PROGRAMMED SENSORS (DIP SWITCH 3-8)
Dip Switches 3-8 provide access to all 63 messages/tones which can be assigned to any zone. Up to 4 messages/tones can be combined to create a custom message. See page 6, CHART 3, for Advanced Dip Switch Message Codes.
ADVANCED PROGRAMMING

Make sure switch is in PROGRAM mode
Press zone/message selection button intended for sensor advanced programming
Move Dip Switches to correct position for selected word
Press zone/message selection button to accept word (repeat for up to four words/tones)
CAUTION – while selecting custom message do not position all Dip Switches back into OFF (down) position. This will reset your entire message!
Move switch to NORMAL mode when complete
Test/trigger sensor

Note: If you make a mistake while programming zone custom message, press acknowledge button to revert to previous message then begin again.

Example of Advanced Programming Message
“(Ding Dong) Customer Service Alert” Four Step Programming

VIEW DIP SWITCH CONTROLS

|

CREATE YOUR OWN CUSTOM MESSAGE

---|---

STEP 1
Press Zone/Message Selection Button

|

MESSAGE CODE

| MESSAGE

STEP 2
Press Zone/Message Selection Button

|

MESSAGE CODE

| MESSAGE
STEP 3
VIEW DIP SWITCH CONTROLS Press Zone/Message Selection Button| MESSAGE CODE|

MESSAGE

STEP 4

Press Zone/Message Selection Button| MESSAGE CODE|

MESSAGE

Key: Dip Switch Location

ADVANCED DIP SWITCH MESSAGE CODES

DIP SWITCH	LANGUAGE
3	4
0	0
0	0
0	1
0	1
1	1
1	0
0	0
1	1
0	0
0	1
0	1
1	1
1	0
0	1
1	0
0	0
0	0
1	0
0	0
0	0
0	0
1	0
0	1
0	1
0	1
0	1
1	1
1	0
0	0
1	0
0	0
1	1
1	1
0	0
0	1
1	0
0	0
1	1
0	1
1	1
0	1
1	1
1	1
1	1
1	0
1	0
1	1
1	1
PROTECTORA0 0 1 1 0	1
1	0
0	1
0	1
1	0
0	0
1	0
1	0
0	1
1	1
1	1
1	1
1	0
1	0
DIP SWITCH	LANGUAGE
---	---
3	4

GROUP
0| 0| 0| 1| 0| 0| | 4-NOTE CHIME| CARILLON DE 4 NOTAS| TONES
0| 0| 0| 1| 0| 1| | 8-NOTE CHIME| CARILLON DE 8 NOTAS
0| 0| 1| 0| 0| 1| | BELL| CAMPANA
0| 0| 1| 0| 1| 0| | BUZZER| ZUMBADOR
0| 0| 0| 0| 0| 1| | DING| TIMBRE (DIN)
0|   0| 0| 0| 1| 0| | DING-DONG| DIN-DON
0|   0| 1| 0| 0| 0| | DOGS| PERROS
0| 0| 0| 0| 1| 1| | DONG| TIMBRE (DON)
0| 0| 0| 1| 1| 1| | JINGLE BELLS| CASCABEL
0| 0| 0| 1| 1| 0| | KNOCK| LLAMADA A LA PUERTA
1| 1| 0| 0| 0| 1| | BARN| GRANERO| LOCATIONS
1| 0| 1| 0| 1| 1| | BASEMENT| SOTANO
1| 0| 1| 1| 1| 0| | DECK| TERRAZA
0| 1| 0| 0| 0| 1| | DRIVEWAY| ENTRADA
1|   0| 0| 0| 0| 1| | DOCK| MUELLE
1| 0| 1| 0| 1| 0| | DOWNSTAIRS| ABAJO
0| 0| 1| 0| 1| 1| | FRONT| FRENTE
1| 0| 1| 1| 0| 1| | GARAGE| GAREJE
1|   1| 0| 0| 0| 0| | HALL| EL PASILLO
1| 0| 1| 1| 0| 0| | KITCHEN| COCINA
1| 0| 1| 1| 1| 1| | PATIO| PATIO
1|   0| 0| 0| 1| 0| | POOL| PISCINA
0| 0| 1| 1| 0| 1| | REAR| TRASERA
1| 0| 0| 0| 1| 1| | SHED| COBERTIZO
0|   0| 1| 1| 0| 0| | SIDE| LADO
1| 0| 1| 0| 0| 1| | UPSTAIRS| ARRIBA
0| 1| 1| 0| 1| 0| | ALERT| ALERTA| ALERTS
0| 1| 1| 1| 0| 1| | ASSISTANCE| ASISTENCIA
0|   1| 1| 0| 0| 1| | CALL| LLAMADA
1|   1| 0| 1| 0| 1| | CLOSE| CERRAR
0| 1| 1| 1| 1| 0| | CUSTOMER| CLIENTE
0| 1| 1| 0| 0| 0| | EMERGENCY| EMERGENCIA
0| 1| 0| 1| 1| 1| | EXIT| SALIDA
0| 1| 0| 1| 1| 0| | EXTINGUISHER| EXTINTOR DE
INCENDIOS0 1 0 1| 0| 1| | MONITOR| MONITOR
1| 1| 1| 0| 0| 1| | MOTION| MOVIMIENTO
1| 1| 0| 1| 0| 0| | OPEN| ABIERTA
1| 1| 1| 0| 1| 1| | PRE-ALERT| PRE-AVISO
0|   1| 1| 1| 1| 1| | SERVICE| SERVICIO
1| 0| 0| 1| 0| 0| | TEMPERATURE| LA TEMPERATURE
0| 1| 1| 0| 1| 1| | THEFT| ROBO
1| 1| 0| 1| 1| 0| | TROUBLE| PROBLEMAS
1| 0| 1| 0| 0| 0| | WATER LEVEL| NIVEL DEL AQUA| OBJECTS
1| 1| 0| 1| 1| 1| | BUTTON| BOTON
0| 1| 0| 0| 1| 1| | CABINET| GABINETE
1| 0| 0| 0| 0| 0| | COVER| CUBIERTA
0| 0| 1| 1| 1| 0| | DOOR| PUERTA
1|   0| 0| 1| 1| 0| | FREEZER| CONGELADOR
0| 0| 1| 1| 1| 1| | GATE| ENTRADA
1| 1| 0| 0| 1| 1| | GUN| PISTOL
0| 1| 1| 1| 0| 0| | KEYFOB| LLAVERO
1|   1| 1| 0| 0| 0| | LIQUOR| LICOR
0| 1| 0| 0| 1| 0| | MAILBOX| BUZON DE CORREO
1|   1| 0| 0| 1| 0| | MEDICINE| MEDICINA
1| 1| 1| 0| 1| 0| PR| OTECTIVE COVER| CUBIERTA
PROTECTORA1 0 0 1 1| 1| | REFRIGERATOR| REFRIGERADOR
0| 1| 0| 1| 0| 0| | SAFE| CAJA FUERTE
1| 0| 0| 1| 0| 1| | SUMP PUMP| POZO DE BOMBEO| #
0| 1| 0| 0| 0| 0| | WINDOW| VENTANA
1| 1| 1| 1| 0| 0| | ONE| UNO
1| 1| 1| 1| 0| 1| | TWO| DOS

DELETE SENSOR

In PROGRAM mode simultaneously press and hold the acknowledge button and zone/ message selection button for three seconds.
Successful when receiver states, “Zone [number] is empty,” and green LED is off.

LOW BATTERY / TAMPER / OUT OF RANGE ALERT

The 4-Zone LED light indicator will turn yellow when maintenance is required on your sensor (example: low battery or tampering with a sensor). The LED will remain on until the trouble condition is cleared and a transmission is received. When replacing the battery in a sensor, you will not need to reprogram into the receiver.

MOUNTING OPTIONS

The receiver can be mounted on a wall or set on a table with the provided stand.

WARRANTY INFORMATION

Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase. Electronic warranty form at www.sti- usa.com/wc14.

IMPORTANT NOTICE

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and devices.
Connect the equipment to an outlet other than the receiver’s.
Consult a dealer or an experienced radio/TV technician for assistance.

Operation is subject to the following two conditions: (1) this device may cause interference, and (2) this device must accept interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by Safety Technology International, Inc. could void your authority to operate this equipment.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
This product meets the applicable industry Canada Technical specifications. Le present materiel est conform aux specifications techniques applicable d’Industrie Canada.

Model: STI-V34104 CAN ICES-3 (B)/NMB-3(B)
This device is a wireless receiver intended for home and office use in all EU and EFTA member states.

TECHNICAL SUPPORT

Contact : STI at 248-673-9898

ADDITIONAL WIRELESS ALERT SERIES PRODUCTS

[

QR Code ](https://www.sti-usa.com/series /wireless-receivers/)
USA EMEA ****

Safety Technology International
2306 Airport Rd • Waterford, MI 48327, USA
Phone: 248-673-9898
Eamil : info@sti-usa.com
Website : www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove, Worcestershire • B60 3DR • England
Tel: +44 (0)1527 520 999 • info@sti-emea.com • www.sti-emea.com
Unit 7A • Lockhead Avenue • Airport Business Park • Waterford • X91 HWF2 • Ireland
Eamil : info@sti-emea.com
Website : www.sti-emea.com