STI-1210 Sounder Strobe Instruction Manual

STI-1210 Sounder Strobe

Product Information

This product is a flush mount horn/strobe appliance. It is designed for installation in various applications to provide visual and auditory signals for alarm systems. The appliance is compatible with existing systems and can be used both indoors and outdoors, provided it carries an outdoor rating. The product comes with a clear section that must be centered over the strobe light lens to minimize light loss transmission. It also includes a damage stopper for compliance with applicable codes and regulations.

Product Usage Instructions

1. Before installation, ensure that added protection is not needed due to environmental conditions. If required, order the KIT-121 ENVIRO KIT.
2. For proper installation, follow these steps:
3. Use the enclosure assembly as a template and place it against the mounting surface at the desired location according to NFPA 72 standards.
4. Mark and drill four holes with a diameter of 1/4 in. (6.3mm) and a depth of 1 in. (25mm).
5. Insert the four anchors provided into the wall.
6. Mount the frame assembly to the wall using the provided screws.
7. If needed, install electrical fittings.
8. Install the horn/strobe appliance, except for retrofit applications.
9. Attach the cover using the provided clips and screws.
10. Test the appliance according to the manufacturer’s instructions.
11. In applications where wash downs, rainfall, or condensation occur, it is recommended to provide a drain or weep hole. Refer to the weep hole installation diagram for guidance.
12. Cleaning instructions: Rinse the appliance with water to remove abrasive dust and dirt. Wash with soap or mild detergent using a soft cloth, avoiding scrubbing. Rinse again and dry with a soft cloth or chamois. To remove grease or wet paint, gently rub with a cloth wetted with naphtha, then wash and rinse. Do not use razor blades.
    Important: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
    The product comes with a three-year warranty or a one-year limited warranty from the date of purchase. More information can be found on the manufacturer’s website at www.sti-usa.com/wc14.

INSTALLATION NOTES

1. To minimize strobe light loss, regardless of the type of horn/strobe appliance used, the clear section (not the section containing the cutout slots) must be centered over the strobe light lens. Failure to follow these instruction may lead to light loss transmission.
2. Damage Stopper must be installed to comply with applicable NEC, NFPA and local codes.
3. In applications where wash downs, rainfall or condensation occur, it is recommended that a drain or weep hole be provided. Refer to weep hole installation diagram.
4. Damage Stopper may be installed outdoors when appliance carries an outdoor rating.

INSTALLATION INSTRUCTIONS – REFER TO EXPLODED VIEW

1. Using enclosure assembly as a template, place against mounting surface at proper location according to NFPA 72.
2. Mark and drill (4) holes 1/4 in. (6.3mm) diameter, 1 in. (25mm) deep.
3. Insert the (4) anchors into the wall.
4.  Mount frame assembly to wall with screws.
5. Install electrical fittings as needed.
6.  Install horn/strobe appliance (except for retrofit applications).
7. Install cover with clips and screws.
8.  Test appliance according to appliance manufacturer’s instructions.

CLEANING INSTRUCTIONS

Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent, using a soft cloth (do not scrub). Rinse once more then dry with a soft cloth or chamois. To remove grease or wet paint, rub gently with a cloth wetted with naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.
WARNING: This product can expose you to chemicals including Dichloromethane, which is known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Three year warranty or a one year limited warranty (from date of purchase) on most products. See website for details. Electronic warranty form at www.sti- usa.com/wc14.

UL INSTALLATION REQUIREMENTS STI-1210 / STI-1221 SERIES

CAUTION

• This enclosure is rated to protect signaling appliances indoors and in areas of indirect weather exposure. The cover may be used outdoors only with devices also suitable for outdoor use.
• When covering fire-signaling appliances with this enclosure, some light and sound loss occurs. Please follow these guidelines listed during installation.
• Voice speaker appliance: No spacing adjustment is required for 0.5W, 1.0W and 2.0W appliances.
• Refer to the appliance manufacturer’s candela rating. Multiply this number by the light loss value from the chart below to determine the new candela rating. Use this number and refer to the notification layout table of NFPA 72 for proper device locations.
• The use of this cover on audible devices decreases the sound output by 6dB(A). Actual sound level output should be checked after installation to determine if adequate sound levels exist. Refer to the notification layout table of NFPA 72 for proper device locations.

Performance Review – LIGHT DERATING FACTOR

MANUFACTURER| SERIES| STI-1210| STI-1221/1221A4X| MANUFACTURER| SERIES| STI-1210| STI-1221/1221A4X
---|---|---|---|---|---|---|---
ADT SECURITY| ADTG1-V SERIES| 40%| 34%| HONEYWELL| XLS202 SERIES| 43%| 45%
AMSECO| SL24W-153075| 47%| 26%| HONEYWELL| XLSG1-HV SERIES| 40%| 34%
AMSECO – COLORED LENSES| SL24W-153075 A, B, G, OR R| 47%| 26%| HONEYWELL| XLSG1-HOV SERIES| 40%| 34%
AMSECO – COLORED LENSES| SL24C-3075110 A, B, G, OR R| 47%| 26%| MIRCOM| FS-240| 47%| 26%
AMSECO – COLORED LENSES| CSL24W-A, B, G, OR R| 47%| 26%| MIRCOM| MS SERIES| 43%| 45%
AMSECO – COLORED LENSES| CSL24C-A, B, G, OR R| 47%| 26%| MIRCOM| MG1-V SERIES| 40%| 34%
DETECTION SYSTEMS| GES24 SERIES| —| 31%| MIRCOM| MG1-HV SERIES| 40%| 34%
EST/EDWARDS| 2440S SERIES| 43%| 45%| MIRCOM| MG1-HOV SERIES| 40%| 34%
EST/EDWARDS| 202 SERIES| 43%| 45%| MIRTONE| MG1-V SERIES| 40%| 34%
EST/EDWARDS| G1-V SERIES| 40%| 34%| NATIONAL TIME & SIGNAL| GES24 SERIES| —| 31%
EST/EDWARDS| G1-HV SERIES| 40%| 34%| POTTER ELECTRIC| AS-24-153075R| 47%| 26%
EST/EDWARDS| G1-HOV SERIES| 40%| 34%| POTTER ELECTRIC| AS-24-153075W| 47%| 26%
EST/EDWARDS| EG1-V SERIES| 40%| 34%| SECUTRON| GES24 SERIES| —| 31%
EST/EDWARDS| EG1-HV SERIES| 40%| 34%| SIEMENS| 202- SERIES| 43%| 45%
EST/EDWARDS| EG1-HOV SERIES| 40%| 34%| SIEMENS| G1-V SERIES| 40%| 34%
FARADAY LLC| 2700| —| 57%| GENTEX| GES24 SERIES| —| 31%
GENTEX| GES24 SERIES| —| 31%| SYSTEM SENSOR| SS24110ADA| 47%| 37%
HARRINGTON SIGNAL| GES24 SERIES| —| 31%| SYSTEM SENSOR| P2, PC2, P4, PC4, SX, SC| 53%| 61%
HONEYWELL| XLSG1-V SERIES| 40%| 34%| ZITON PTY LTD| ZG1-V SERIES| 40%| 34%

ABOUT COMPANY

• SAFETY TECHNOLOGY INTERNATIONAL
• www.sti-usa.com
• www.sti-emea.com

References

• P65Warnings.ca.gov
• Home - STI EMEA
• Security & Safety Device Protection | Safety Technology International
• Warranty & Returns - STI US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>