SR Smith Residential Board Fiberglass Installation Guide
- June 12, 2024
- SR Smith
Table of Contents
SR Smith Residential Board Fiberglass Installation Guide
ASSEMBLY AND INSTALLATION INSTRUCTIONS
–PLEASE READ CAREFULLY–
POOL WATER ENVELOPE DIMENSIONS MUST MEET OR EXCEED ANSI/APSP/ICC-5 2011 STANDARDS FOR THIS BOARD. USE ONLY WITH A COMPATIBLE S.R. SMITH DIVING BOARD STAND. S.R. SMITH DIVING BOARDS AND RELATED EQUIPMENT ARE FOR IN-GROUND POOLS ONLY. DO NOT USE WITH OTHER POOLS, DOCKS, ETC.
USE WITH AN IMPROPERLY-SIZED POOL, INCOMPATIBLE STAND, OR IMPROPER INSTALLATION MAY RESULT IN DEATH OR SERIOUS INJURY.
ATTENTION: THESE INSTRUCTIONS MUST REMAIN WITH PLATFORM OWNER
PROFESSIONAL INSTALLATION RECOMMENDED. IMPROPER INSTALLATION VOIDS S.R.
SMITH’S LIMITED PRODUCT WARRANTY
REGISTER YOUR S.R. SMITH PRODUCT AT
SRS AUSTRALIA, PTY LTD
12 Enterprise St
Richlands QLD 4077
Australia
Phone 07 3812 2283 • Fax 07 3812 1187
www.srsmith.com/au
www.srsmith.com/en/customer-service/product- registration
Visit srsmith.com for information on the complete line of S.R.Smith pool products.
S.R. SMITH, LLC
CORPORATE HEADQUARTERS
P.O. Box 400 • 1017 S.W. Berg Parkway
Canby, Oregon 97013
USA
Phone (503) 266 2231 • Fax (503) 266 4334
www.srsmith.com
FIBRE-DIVE ● FRONTIER III ● GLAS-HIDE
IMPORTANT NOTICE:
IT IS NECESSARY TO USE AN ANTI-SEIZE COMPOUND ON ALL STAINLESS STEEL HARDWARE.
FAILURE TO USE ANTI-SEIZE COMPOUND MAY RESULT IN GALLING AND SEIZING OF THE
HARDWARE.
INSTALLATION INSTRUCTIONS
CONCRETE DEPTH AROUND JIG MUST BE 6” THICK MINIMUM.
- Verify that the pool water envelope dimensions meet or exceed ANSI/APSP/ICC-5 2011 standards for this board. Excerpt from the applicable ANSI/APSP/ICC-5 2011 standard are attached and more information on safe installation is available at www.srsmith.com/. Warning: using the diving board with an improperly-sized pool may result in death or serious injury.
- Verify that the board is compatible with the installed S.R. Smith diving board stand. A matrix of compatible products is attached and available at www.srsmith.com/.
- Verify that the diving board stand is properly and securely installed. The concrete deck around the diving board stand must be 6” thick minimum.
- THE DIVING BOARD WARRANTY WILL BE VOID if the correct measurement between the mounting holes and the fulcrum is not maintained when mounting a diving board to a newly installed stand.
5. The Rubber Fulcrum Pad MUST be used so as not to void S.R. Smith’s
warranty.
6. Install board using fasteners provided as shown in FIGURE B. Tighten hex
nuts until lock washer is fully compressed. DO NOT OVERTIGHTEN. It is
necessary to use an anti-seize compound on all stainless steel hardware.
Failure to use anti-seize compound may result in galling and seizing of the
hardware.
ONLY ONE PERSON ON DIVING PLATFORM AT A TIME WITH A MAXIMUM WEIGHT OF 250 LBS (113KG)
For SI: 1 degree = 0.017 rad, 1 inch = 25.4 mm, 1 foot = 304.8 mm
Read More About This Manual & Download PDF:
References
- Pool Deck Equipment - Pool Slides And Diving Boards | S.R.Smith
- Pool Deck Equipment - Pool Slides And Diving Boards | S.R.Smith
- Pool Deck Equipment - Pool Slides And Diving Boards | S.R.Smith
- Pool Deck Equipment - Pool Slides And Diving Boards | S.R.Smith
- Register Your Pool Product | S.R. Smith
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>