VENTO 169204 Dimmable Ceiling Fan Instruction Manual

VENTO 169204 Dimmable Ceiling Fan Instruction Manual

You may use the following QR code to view the complete technical data sheet of the product:

If you have any technical questions, please do not hesitate to contact our technical Department. We are at your disposal in our email: irodriguez@schuller.es

WARNING

1. This ceiling fan requires a power input of 220 V / 50 HZ.
2. The electrical installation should be carried out by a qualified electrician.
3. To reduce risk of injury, do not touch the blades while the fan is in operation. INSTRUCTIONS AND

INSTALLATION STEPS

1. List of component
2. Ceiling-mount bracket 2-Canopy downrods (2A: short y 2B: long)
3. Canopy
4. Connector cover
5. Fan body (includes LED circuit)
6. Connector module
7. Light shade (Acrylic diffuser)
8. Screws pack (installation tools: including magnets and screws)
9. Remote control (AAA batteries included)
   

INSTALLATION OF THE CELLING MOUNT BRACKET

Drill two acquired deep holes into the ceiling, using 8mm drill bit, and insert two expansion or 4 plaster screws bolts into the holes. Then, fix the ceiling-mount bracket onto the expansion bolts and tighten the nuts until the bracket is firmly fixed to the ceiling.
1- celling mount bracket

Installation of the suspension system.

1. Select the downrod (2A or 2B) you wish to use according to the desired height of the fan.

2. If it isn’t already been pre-installed, use the pin and set-screw to insert the hemisphere onto the selected downrod.
   

3. Place the canopy and the connector cover onto the tube, in the order indicated in the diagram below.

4. Loosen the screws and remove the pin from the connector ring (placed in the upper part of the fan body) and insert the downrod tube, after having previously fed the wires through the tube. Rotate until the holes are aligned and reinsert the pin, secure with the R-clip, and tighten the ring screws until the tube is firmly fixed in place (tighten the screws on all sides to an equal depth so that the tube is centred). Cover the connecting ring with the connector cover.
   

5. Place the tube down rod with the semi-sphere on the mounting bracket, and rotate the assembly until it engages the four snap- in slots and is firmly seated.
   

6. Next to the ceiling bracket, connect the module to the wires that come out from the top downrod topside. Then connect the network cable to the INPUT cables of the module. Once all are connected, insert the module into the reserved space on the ceiling- mount.(with adhesive pads to attenuate possible sounds due to vibration of the module)
   

7. Raise the canopy to the ceiling to cover the ceiling-mount (ensuring the canopy rests on the two bracket screws), rotate the canopy to ensure the screw headsalign with the holes on the bracket, and tighten the screws.
   

8. Place the light shade on the underside of the fan body, covering the LEDring. Ensure the grooves on the shade diffuser align with the pivots on the ring of the fan body, then turn the shade diffuser clockwise until it fixes in place.
   

Balance adjustment for this fan. “Invisible system”

Although the fans are balanced before shipping, balance can be affected by transit. As a consequence, re-balance the fan by following these steps if you find that the fan has a noticeable wobbleonce fully assembled.

1. Remove the balance kit from the packaging and place two of the balance magnets onany of the marked spaces, as shown in Figure A. Then turn the fan on to see if it continues to wobble. Repeat this until you find the position that corrects the wobble and allows the fan to run smoothly.
2. Remove the balance magnets and attachthe balance kit in order to stick them in place. Figure B
   
   

TROUBLESHOOTING

1. The fan won’t start.
   • Check the fan wiring; ensure all the cables are connected correctly.
   • Check and ensure that the input power is correct at 220V/50HZ
2. The fan makes a loud noise
   • Ensure all the screws have been tightened correctly.
   • Ensure the wire nut connections are not rubbing against each other or against the inside of the canopy box.

REMARKS

1. The first 24 hours after installation, it is normal to notice a slight noise during fan operation. After this
   adjustment period, the rumor will disappear.

2. The light of the fan turned off through the remote control remains in stand-by mode. It will be completely off if power is cut off through the wall switch.

3. If you are installing the fan in a false ceiling made of plaster, Wood or metal, the noise of the fan may be amplified due to the existing air chamber. We recommend adding an insulating material in the ceiling chamber to mitigate the transmission of sound.

4. From the wall switch you can also use the lighting functions of the K button (10)

REMOTE CONTROL USERS GUIDE

1. Fan OF
2. Nature wind. (Changing speed/Fan ON: Turn on in the last F/R function.)
3. Fan ON. Turn on at the desired speed
4. Foward / Reverse
5. Ligth ON / OFF alternate color change
6. Reduce brightness
7. Increase brightness
8. Lower color temperatureforward
9. Raise color temperature fordwa
10. Selector 3000k, 4500k, 6000k
11. Fan timer
    2 1,5V AAA battery

Notices

1. Each remote control is originally synchronized with its own fan. Another remote control will not make the fan work. Do not swap them.
2. To link the remote control with the fan light, immediately after turning the fan on, press and hold the F/R button for a few seconds until a beep sounds.
3. When the remote control fails, Please check whether the switch batteries are in good contact, whether they are fixed properly and whether they run out of use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>