Genesis Power Tools GLGT08B 8V Cordless Garden Trim Kit Instruction Manual

: June 12, 2024
: Genesis Power Tools

Table of Contents

Genesis Power Tools GLGT08B 8V Cordless Garden Trim Kit
Product Information
Product Usage Instructions
SPECIFICATIONS
GENERAL SAFETY RULES
EXTENSION CORDS
SPECIFIC SAFETY RULES FOR CORDLESS GARDEN TRIMMERS
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY
KNOW YOUR CORDLESS GARDEN TRIM KIT
UNPACKING AND CONTENT
ASSEMBLY AND ADJUSTMENTS
OPERATION
APPLICATIONS
MAINTENANCE
TWO-YEAR WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Genesis Power Tools GLGT08B 8V Cordless Garden Trim Kit

Product Information

Product Name: GLGT08B 8V Cordless Garden Trim Kit
Includes: Trimming Blade, Shearing Blade, Battery, Charging Stand, and Charging Adaptor
Manufacturer: Genesis Power Tools
Toll-Free Help Line: 888-552-8665
Website: www.genesispowertools.com

Product Usage Instructions

Safety Precautions:

Before operating the tool, read and understand the operator’s manual to reduce the risk of injury.
Always wear safety goggles or safety glasses with side shields and a full face shield when using the tool to protect your eyes.
We recommend using the Wide Vision Safety Mask or standard safety glasses marked to comply with ANSI Z87.1.
Work in a well-ventilated area and use approved safety equipment, such as dust masks, to minimize exposure to harmful chemicals.

Work Area Safety:

Ensure your work area is clear and free from hazards that may cause you to lose control of the tool.

Electrical Safety:

Follow all electrical safety precautions when using the tool.

Personal Safety:

Adhere to all personal safety guidelines while using the tool.

Tool Use and Care:

Read and understand all warnings, cautions, and operating instructions before using the tool.
Properly maintain and care for the tool to ensure its safe and efficient operation.

Battery Tool Use and Care:

Follow all instructions and guidelines for using and caring for the battery-powered tool.

Extension Cords:

Use a three-wire extension cord for grounded tools.
Refer to the recommended minimum wire gauge chart for extension cord length and nameplate amperes.

Specific Safety Rules for Cordless Garden Trimmers:

Do not let comfort or familiarity replace strict adherence to product safety rules.
Hold the tool by insulated gripping surfaces when performing any operation.

For more detailed information and instructions, refer to the product’s operator’s manual.

SPECIFICATIONS

Model ……………………………………………….. GLGT08B
Motor Power …………………………………….. 8V DC
No Load Speed ………………………………….. 1000 RPM
Battery …………………………………………….. 8V, Lithium-Ion, 2000 mAh
Charger ……………………………………………..120V~/60Hz, 0.4A
Charging Time …………………………………… 3-5 Hours
Trimming Blade Length ……………………….. 5″
Trimming Blade Cutting Capacity ………….. 3/8″
Shearing Blade Width …………………………. 3″
Net Weight ………………………………………… 1.5 lb

Includes: Trimming Blade, Shearing Blade, Battery, Charging Stand, and Charging Adaptor

WARNING: To reduce the risk of injury, user must read and understand this operator’s manual before operating this tool. Save this Manual for future reference.
Toll-Free Help Line: 1-888-552-8665

WARNING: The Operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87.1.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

GENERAL SAFETY RULES

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

Lead from lead-based paints.
Crystalline silica from bricks and cement and other masonry products.
Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to ﬁlter out microscopic particles.

WARNING: Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in electric shock, ﬁre and/or serious personal injury.
SAVE THESE INSTRUCTIONS

WORK AREA SAFETY

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs in any earthed (grounded) power tools. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will ﬁt in a polarized outlet only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk of electric shock.
When operating a power tool outside, use an extension cord suitable for outdoor use. These cords are rated for outdoor use and reduce the risk of electric shock.
Do not use AC only rated tools with a DC power supply. While the tool may appear to work. The electrical components of the AC rated tool are likely to fail and rate a hazard to the operator.

PERSONAL SAFETY

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use the tool while tired or under the inﬂuence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection for appropriate conditions will reduce personal injuries.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from the moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents may cover moving parts and should be avoided.
Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying a power tool with your ﬁnger on the switch or plugging in power tools that have the switch on invites accidents.
Remove any adjusting keys or wrenches before turning the power tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause an injury in an unexpected situation.
If devices are provided for connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.
Do not use a ladder or unstable support. Stable footing on a solid surface enables better control of the tool in unexpected situations.
Keep tool handles dry, clean and free from oil and grease. Slippery handles cannot safely control the tool.

TOOL USE AND CARE

Secure the workpiece. Use clamp or other practical way to hold the workpiece to a stable platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of control.
Do not force the power tool. The tool will perform the job better and safer at the feed rate for which it is designed. Forcing the tool could possibly damage the tool and may result in personal injury.
Use the correct power tool for the job. Don’t force the tool or attachment to do a job for which it is not designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired or replaced by an authorized service center.
Turn the power tool off, and disconnect the plug from the power source and/or battery pack from the power tool before making any adjustments, changing the accessories, or storing the tools. Such preventive safety measures reduce the risk of an accidental start up which may cause personal injury.
Store idle tool out of reach of children and other inexperienced persons. It is dangerous in the hand of untrained users.
Maintain power tools with care. Check for proper alignment and binding of moving parts, component breaks, and any other conditions that may affect the tool’s operation. A guard or any other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.
Use recommended accessories. Using accessories and attachments not recommended by the manufacturer or intended for use on this type tool may cause damage to the tool or result in personal injury to the user. Consult the operator’s manual for recommended accessories.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Feed the workpiece in the correct direction and speed. Feed the workpiece into a blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly feeding the workpiece in the same direction may cause the workpiece to be thrown out at high speed.
Never leave the tool running unattended, turn the power off. Do not leave the tool until it comes to a complete stop.

BATTERY TOOL USE AND CARE

Ensure the switch trigger is in the off position before inserting battery pack. Inserting the battery pack into a power tool that has the switch on invites accidents.
Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of ﬁre when used with another battery pack.
Use battery tools only with speciﬁed battery packs. Use of any other battery packs may create a risk of injury and ﬁre.
Avoid storing the battery pack in a container with other metal objects such as nails, coins, clips, keys, screws, or other small metal objects that can make a connection from one terminal to another. Always protect the battery terminals when battery pack is not being used. Connecting the battery terminals together may cause burns or a ﬁre.
Under abusive conditions, liquid may be ejected from the battery. Avoid contact. If contact accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Battery tools do not need to be plugged into an electrical outlet, therefore, they are always in an operation condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, ﬁre or personal injury.

WARNING: USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST AND ASBESTOS. Direct particles away from face and body. Always operate tool in a well- ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly ﬁtting NIOSH/OSHA approved respiratory protection appropriate for dust exposure, and wash exposed areas with soap and water.

SERVICE

Have your power tool serviced by a qualiﬁed repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Service your power tool periodically. When cleaning a tool, be careful not to disassemble any portion of the tool since internal wires may be misplaced or pinched.

WARNING: READ AND UNDERSTAND ALL WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below may result in electric shock, ﬁre and/or serious personal injury.

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can
use either a two or three wire extension cord. As the distance from the power supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown below to determine the required minimum wire size.
The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-gauge cord can carry a higher current than a 16-gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

If you are using an extension cord outdoors, be sure it is marked with the sufﬁx “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.
Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualiﬁed person before using it.
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

Recommended Minimum Wire Gauge for Extension Cords (120 Volt)

Nameplate Amperes

(At Full Load)

| Extension Cord Length
25 Feet| 50 Feet| 75 Feet| 100 Feet| 150 Feet| 200 Feet
0–2.0| 18| 18| 18| 18| 16| 16
2.1–3.4| 18| 18| 18| 16| 14| 14
3.5–5.0| 18| 18| 16| 14| 12| 12
5.1–7.0| 18| 16| 14| 12| 12| 10
7.1–12.0| 18| 14| 12| 10| 8| 8
12.1–16.0| 14| 12| 10| 10| 8| 6
16.1–20.0| 12| 10| 8| 8| 6| 6

SPECIFIC SAFETY RULES FOR CORDLESS GARDEN TRIMMERS

WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH THE PRODUCT
(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO PRODUCT SAFETY RULES. If you use this tool unsafe or incorrectly, you can suffer serious personal injury!
WARNING: Hold the tool by insulated gripping surfaces when performing an operation where cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator!
WARNING: Keep hands, loose clothing, and other objects not intended to be cut away from blades!

Always wear safety glasses or goggles. Normal prescription eye or sunglasses are not safety glasses.
Always hold the tool ﬁrmly. Do not leave the tool running unless hand held.
Check your work area for proper clearances before cutting. This will avoid cutting into unintended objects.
Do not try to grasp or remove trimmings when the tool is running. Only remove trimmings when the tool is switched off and disconnected from the power supply.
Before switching on the tool, be sure the blade is not contacting the cutting objects.
Do not use tool if switch does not turn it on or off. Any tool which can not be controlled by the switch is dangerous and must be repaired.
Wear cushioned protective gloves to minimize the vibration. Excessive vibration may cause personal injury.
Always disconnect battery pack from tool or place the switch in the locked or off position before any assembly, adjustments or changing of accessories. Following this instruction will reduce the risk of serious personal injury.
Do not place battery tools or their batteries near ﬁre or heat. This will reduce the risk of explosion and possibly personal injury.
Never use a battery which has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
Use designated battery packs (Genesis™ Model GLAB0820B or GLAB08B) for this tool. Use of any other batteries may result in a risk of ﬁre.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY

Save these instructions. This manual contains important safety and operating instructions for your battery charger.
Before using the battery charger, read all instructions and cautionary markings on (1) Battery Charger, (2) Battery, and (3) Product using battery.
Use only the charger which accompanied your product or direct replacements as listed in this manual. Do not substitute any other charger.
Do not recharge the battery in damp or wet environments. Do not expose the battery pack to water or rain.
Do not operate the charger with damaged cord or plug. Replace immediately.
Do not operate a charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to a qualiﬁed serviceman.
Do not disassemble a charger or a battery pack. Take it to a qualiﬁed serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or ﬁre.
Do not charge the battery pack when temperature is below 50° F (10° C) or above 104 ° F (40°
C). Store the tool and battery pack in a location where temperature will not exceed 122° F (50° C). This is important to prevent serious damage to the battery cells.
Place the charger on ﬂat non-ﬂammable surface and away from ﬂammable materials when re-charging the battery pack.
To reduce risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning.
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
Battery leakage may occur under extreme usage or temperature conditions. Avoid contact with skin and eyes. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, wash them out with clear water for at least 10 minutes, and then seek medical attention right away.
Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.
Do not short the battery pack. Do not touch the terminal with any conductive material. Avoid storing battery pack in a container with other metal objects such as nails, coins, etc. Always protect the battery terminals when battery pack is not used.
Do not charge a battery pack inside a box or container of any kind. The battery must be placed in a well ventilated area during charging.
Do not allow anything to cover or clog the charger vents.
Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a ﬁre.
Disconnect the charger from the power source when not in use. This will reduce the risk to electric shock or damage to the charger if metal pieces should fall into the opening. It also will help prevent damage to the charger during a power surge.

WARNING: A battery short can cause a large current ﬂow, overheating, possible burns and even a breakdown.
IMPORTANT BATTERY INFORMATION: DISPOSING OF THE BATTERY

Your batteries are LITHIUM-ION rechargeable batteries. Certain Local, State and Federal laws prohibit disposal of these batteries in ordinary trash.
Consult your local waste authorities for your disposal/recycling options.
More information regarding battery disposal in U.S. and Canada is available at;
http://www.rbrc.org/index.html, or by calling 1-800-822-8837 (1-800-8BATTERY).

SAVE THESE INSTRUCTIONS

KNOW YOUR CORDLESS GARDEN TRIM KIT

Power Handle
Lock-Off Switch
On/Off Switch
Battery
Battery Locking Tab
Trimming Blade
Shearing Blade
Blade Release
Charging Stand
Charging Adaptor

UNPACKING AND CONTENT

IMPORTANT: Due to modern mass production techniques, it is unlikely the product is faulty or that a part is missing. If you ﬁnd anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectiﬁed. Failure to do so could result in serious personal injury.

CONTENTS IN PACKAGE:

Description : QTY

Power Handle 1
Battery Pack (GLAB0820B) 1
Trimming Blade 1
Shearing Blade (Installed) 1
Charging Stand 1
Charging Adaptor 1

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injuries, read and follow all important safety warning and instructions before using this tool.
WARNING: Always be sure that the tool is switched off before insertion or removal of the battery pack.

INSTALLING AND REMOVING BLADES

WARNING: Always remove battery pack from tool or place the switch in the locked or off position before any assembly, adjustments or changing accessories.

To Remove Blade (Fig 2)

Press both release buttons (8-ﬁg 1) on either side of the installed blade at the same time.
Tilt the blade down away from the power handle to remove.

NOTE: It is recommended to place the appropriate blade cover onto the blades when stored.

To Attach Blade (Fig 3)

Place the back end of the blade into the power handle.
Tilt the blade up into the power handle until it locks.

OPERATION

WARNING: To reduce the risk of serious personal injuries, read and follow all important safety warning and instructions before using this tool.
NOTE: To conform with UN shipping requirements, lithium-ion batteries are shipped with a partial charge. For best performance, fully charge the batteries prior to ﬁrst use. Follow charging instructions per this manual.
WARNING: Always be sure that the tool is switched off before insertion or removal of the battery pack.
NOTE: BATTERY and TOOL PROTECTION FEATURES: Genesis Lithium-ion batteries and tools are designed with features that protect the lithium-ion cells and maximize battery life. If the tool stops during use, release the trigger to reset and resume the operation. If the tool still does not work, the battery needs to be recharged.

INSTALLING OR REMOVING THE BATTERY (FIG 4)

To install the battery pack, insert the battery pack into the bottom of the tool all the way until it locks in place with a click, as shown in Fig 4.
To remove the battery pack, slide the battery locking tab (5) as shown in Fig 4, to release the battery pack, then remove the battery pack.

CHARGING THE BATTERY (FIG 5)
NOTE: Always check that the power supply corresponds to the voltage on the ratings plate.

Connect the charging adaptor (10) and the charging stand (9).
Plug the adaptor into a 120 Volt AC power source. The GREEN light on the charging stand will illuminate, indicating the charger is powered.
Insert the battery (4) all the way into the charging stand until it locks in place with a click, as shown in Fig 5. The RED light on the stand indicates that the battery is charging.
The light will turn GREEN after charging is complete.
To remove the battery from the stand, depress the locking tab (c) on the stand to release the battery pack.
Batteries may become warm while charging. This is normal.
If battery is hot after continuous use in the tool, allow it to cool down to room temperature before charging. This will extend the life of your batteries.

NOTE: It takes approximately 3-5 hours to charge up a completely discharged battery.

SWITCH ACTION (FIG 6)
Locate the lock-off switch (2) on the top and the On/Off switch (3) on the bottom of the tool handle. To Turn On the Tool, slide the lock-off switch forward, then pull the On/Off switch up.
To Turn Off the Tool, release both the lock-off and On/Off buttons.

APPLICATIONS

TRIMMING BLADE (6-FIG1)
Use this blade to trim and shape plants and bushes with branches up to 3/8 inch diameter.
( TIP: For best cutting, slightly tilt the blade toward the direction of cut. )

SHEARING BLADE (7-FIG1)
Use this blade for detailed cutting and trimming of light areas of plants and bushes such as new growth and leaves.

MAINTENANCE

CLEANING
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING: Do not at any time let brake ﬂuids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result in serious personal injury.
Electric tools used on ﬁberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the ﬁberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air.

LUBRICATION
This tool is permanently lubricated at the factory and requires no additional lubrication.

TWO-YEAR WARRANTY

This product is warranted free from defects in material and workmanship for 2 years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call Toll-Free Help Line for possible solutions.
THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES. ACCESSORIES INCLUDED IN THIS KIT ARE NOT COVERED BY THE 2 YEAR WARRANTY. BATTERY INCLUDED IS WARRANTED FOR ONE (1) YEAR AFTER DATE OF PURCHASE.

TOLL-FREE HELP LINE
For questions about this or any other GENESIS products, please call Toll-Free: 888-552-8665. Or visit our web site: www.genesispowertools.com
©Richpower Industries, Inc. All Rights reserved
Richpower Industries, Inc.
736 Hampton Road
Williamston, SC 29697

Richpower Industries, Inc.
736 Hampton Road
Williamston, SC USA
www.richpowerinc.com
2022.12. V01