Room Board COLES Bathroom Vanities Installation Guide

: June 12, 2024
: Room Board

Table of Contents

PROFESSIONAL INSTALLATION RECOMMENDED
Coles Vanities
Vanity Tops and Sinks

COLES VANITIES INSTALLATION AND SPECIFICATIONS

CAUTION

PROFESSIONAL INSTALLATION RECOMMENDED

Please inspect your new vanity prior to installation. Once the vanity has been installed or altered, such as cutting the cabinet’s back panel or adhering the top, it cannot be returned. If you notice any damage or defects, please contact us at 800.486.6554 or shop@roomandboard.com for assistance.

Moving and Storage

Keep in original packaging until installation to protect from damage.
Do not stack anything on top of the packaging.
Use a two-person team to lift and move.

Installation Requirements

Professional installation with a two-person team.
Water supply and plumbing installed according to local code.
Level floor and plumb walls at installation site.

Vanity Installation Recommendations

Cut or drill holes in the back or bottom panel of the vanity cabinet to accommodate plumbing.
Attach the vanity cabinet securely to the wall using appropriate hardware for your wall material.
If needed, use the supplied leveler feet to accommodate a floor that is not level. To use, remove plastic foot caps, insert the levelers and set at the desired height.

Top Installation Recommendations

Apply a nickel-sized amount of clear 100% silicone to all four corners of the top edge of the vanity cabinet.
Using a two-person team, lift and place the vanity top. Lower it slowly; do not drop it onto the vanity cabinet.
Wipe off excess silicone immediately.

Backsplash and Side Splash Installation Recommendations

Apply a nickel-sized amount of clear 100% silicone every eight to ten inches on the wall where the backsplash will be installed.
Install the backsplash by gently pushing it onto the wall and centering it on the top.
If you selected a left overhang or right overhang top, a side splash is included. Install the side splash after the backsplash.
Once cured, run a small bead of 100% clear silicone along the joint where the backsplash and optional side splash meet the vanity top.

For wood and quartz cleaning and care information, visit roomandboard.com/care

Coles Vanities

Side view measurements apply to all vanity sizes and both sink shapes.

26w 21.75d 34h Single-Sink Vanity Tops with an overhang left side only or right side only are 25.25″ wide.

36w 21.75d 34h Single-Sink Vanity Tops with an overhang left side only or right side only are 35.25″ wide.

48w 21.75d 34h Single-Sink Vanity Tops with an overhang left side only or right side only are 47.25″ wide.

60w 21.75d 34h Single-Sink Vanity Tops with an overhang left side only or right side only are 59.25″ wide.

60w 21.75d 34h Double-Sink Vanity Tops with an overhang left side only or right side only are 59.25″ wide.

72w 21.75d 34h Double-Sink Vanity Tops with an overhang left side only or right side only are 71.25″ wide.

Vanity Tops and Sinks

All vanity tops available with left and right side overhang, no overhang, overhang left side only or overhang right side only.
Backsplash included; side splash included for overhang left side only or overhang right side only.

Rectangular sink front view

Oval sink front view

26″ and 36″ RECTANGULAR SINKS, single faucet hole

26″ and 36″ RECTANGULAR SINKS, 8″ spread faucet holes

26″ and 36″ OVAL SINKS, single faucet hole

26w 21.75d 34h Single-Sink Vanity
Tops with no overhang are 24.5″ wide; tops with an overhang left side only or right side only are 25.25″ wide.

36w 21.75d 34h Single-Sink Vanity
Tops with no overhang are 34.5″ wide; tops with an overhang left side only or right side only are 35.25″ wide.

48″ RECTANGULAR SINKS, single faucet hole

48″ RECTANGULAR SINKS, 8″ spread faucet holes

48″ OVAL SINKS, single faucet hole

48″ OVAL SINKS, 8″ spread faucet holes

48w 21.75d 34h Single-Sink Vanity
Tops with no overhang are 46.5″ wide; tops with an overhang left side only or right side only are 47.25″ wide.