JOY-iT JT-Line01 Cable Locator and Wall Scanner User Manual

: June 13, 2024
: JOY-It

WALL SCANNER

JOY-iT JT-Line01 Cable Locator and Wall Scanner A0

FOR MAKERS AND PROFESSIONALS

1. GENERAL INFORMATION

Dear Customer,
thank you for choosing our product. In the following, we will show you what to pay attention to during commissioning and use. If you encounter any unexpected problems during use, please feel free to contact us.

2. SPECIFICATIONS

GENERAL SPECIFICATIONS

BATTERY CAPACITY: 3.7 V, 300 MAH
DIMENSIONS: 138 X 68 X 22 MM
AUTOMATIC SHUTDOWN: AFTER ABOUT 5 MIN.
OPERATING TIME: ABOUT 2 HOURS

MAXIMUM DETECTION DEPTH

FERROUS METALS: 120 MM
NON FERROURS METALS (COPPER): 100 MM
LIVE WIRES (230 V): 50 MM
SINGLE STRAND COPPER WIRE: 50 MM
WOOD: 20 MM (PRECISION MODE), 38 MM (DEPTH MODE)

TEMPERATURE RANGE

OPERATING TEMPERATURE: -10 °C – 50 °C
STORAGE TEMPERATURE -20 °C – 70 °C

3. DEVICE OVERVIEW

LED-INDICATOR
DISPLAY
ODRPIELNLIHNGOLFEOR MARKING
DETECTION MODE SELECTION

Wood detection mode. Press and hold to switch between Precision mode and Depth mode. Press shortly to perform the calibration.

Metal and cable detection mode. Press shortly to switch between metal detection and cable detection.

+ Press and hold to turn audio feedback on or off.

4. DISPLAY

PRECISION MODE IN WOOD MODE
DEPTH MODE IN WOOD MODE
DETECTION MODE
SIGNAL STRENGTH
DISTANCE
DISTANCE TO THE EDGE OF THE OBJECT
HINTS FOR WOOD RECOGNITION
CHARGE STATUS AUDIO-FEEDBACK

5. NOTES

Before operating the detector, make sure that there is no moisture on the detection area. Dry the detector with a cloth if necessary.

Make sure that no moisture enters the detector. Do not allow sunlight to shine directly on the detector for extended periods of time.

The use or operation of transmitters or machines that generate a strong, electromagnetic field (e.g. microwaves) can affect the detection results.

For best results, do not wear jewelry such as rings or watches when using the detector. Metal objects may cause inaccurate detection.

When detecting wood, the tool must always be in contact with the wall surface during the scan. Make sure that the fingers of the hand holding the tool do not touch the surface to be scanned.

Under certain conditions (e.g. behind metallic or conductive surfaces or on damp walls), detection may not be reliable.

Do not work with the detector in explosive environments or in environments where flammable liquids, gases or dusts are present.

For technological reasons, the detector cannot guarantee one hundred percent safety. To exclude hazards, be sure to secure yourself with other sources of information, such as construction plans, before working.

Please note that this device is only a tool and cannot provide a 100% reliable result due to the variety of materials and their compound. You use this device at your own risk, we assume no liability for damages resulting from the use of the device and exclude liability to the extent permitted by law. There may be false detections as well as lines/materials not being detected. If plans are available, please consult them.

If you use other tools, please ensure that you wear appropriate protective equipment when working, e.g. consult the instructions for the tool used.

When drilling, we recommend that you find out in advance where the shut-off devices are located and ensure that they are freely accessible so that you can react quickly if the worst comes to the worst.

6. USAGE

BASIC INFORMATION AND OPERATION:

After switching on the detector, it is in metal detection mode by default. If the display shows a signal in a metal-free environment, calibration is required.

CALIBRATION:

Hold the detector in a metal-free environment (e.g. in the air). Now press and hold the metal detection mode button until the signal display returns to zero and the green light illuminates again. Now release the key. The calibration is completed.

DETECTION MODE:

Press the key for the mode you want to switch to. The currently active mode is shown on the display.

DETECTION:

Place the detector on the object surface and move the device. As the device approaches the object, the signal strength scale will automatically increase. The yellow or red LED will additionally light up.

The wood detection mode detects objects in plasterboard walls, plywood cladding, wooden floors and coated wood. Foreign objects cannot be reliably detected in concrete, mortar, brick, carpets, foil surfaces, metal surfaces, tiles or glass.

When switching to the foreign object detection mode, the device must lie still on the surface for approx. 1 – 3 seconds to perform the automatic calibration. The status of the calibration is shown on the display.

7. ADDITIONAL INFORMATION

Our information and take-back obligations under the Electrical and Electronic Equipment Act (ElektroG)

SYMBOL ON ELECTRICAL AND ELECTRONIC EQUIPMENT:
This crossed-out trash can means that electrical and electronic equipment does not belong in the household trash. You must hand in the old equipment at a collection point. Before handing in, you must separate used batteries and accumulators that are not enclosed in the old device from the old device.

RETURN OPTIONS:
As an end user, when you purchase a new device, you can return your old device (which essentially fulfills the same function as the new one purchased from us) for disposal free of charge. Small appliances with no external dimensions larger than 25 cm can be returned in household quantities, regardless of the purchase of a new appliance.

POSSIBILITY RETURN TO OUR COMPANY LOCATION DURING OPENING HOURS:
SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn

POSSIBILITY RETURN IN YOUR AREA:
We will send you a parcel stamp with which you can return the device to us free of charge. To do this, please contact us by e-mail at Service@joy- it.net or by phone.

PACKAGING INFORMATION:
Please pack your old device securely for transport. If you do not have suitable packaging material or do not wish to use your own, please contact us and we will send you suitable packaging.

8. SUPPORT

We are also there for you after the purchase. If any questions remain or problems arise, we are also available to assist you via email, phone and ticket support system.

E-Mail: service@joy-it.net
Ticket-System: http://support.joy-it.net
Phone: +49 (0)2845 9360 50 (10 – 17 Uhr)

For more information visit our website:

www.joy-it.net

FOR MAKERS AND PROFESSIONALS

WWW.JOY-IT.NET
Joy-IT powered by SIMAC Electronics GmbH
Pascalstr. 8 – D-47506 Neukirchen-Vluyn