Merano Tanaro Wall Mounted Bath Mixer Tap with Crosshead Handles Installation Guide

Merano Tanaro Wall Mounted Bath Mixer Tap with Crosshead Handles

Product Information

The product is a single lever wall-mounted mixer. Please note that the appearance of the product may vary depending on the model.

Installation Procedure

1. Prior to installation, flush all supply pipes to remove debris and turn off the water supply.
2. It is strongly recommended to install service isolation valves for easier future maintenance.
3. Ensure you have all the necessary tools and pay attention to any specific markings on the product for correct installation.
4. Create a wall opening that is suitable for the manifold body, ensuring it is large enough for maintenance purposes.
5. Securely connect the manifold to a suitable fixing point inside the wall cavity using the provided fixing lugs. Use appropriate fixings for these connection points (not supplied).
6. Connect the water supplies as indicated on the manifold body.
7. Check all water feed connections for leaks.
8. Assemble the flanges/wall plate and apply a small bead of silicone around them to create a water-tight seal around the cover plate(s).
9. Connect the spout and secure it in place using the grub screws located on the underside of the spout.
10. Fit the operating handle(s).
11. Check the assembled fit of the products to ensure there is no water ingress that may cause water damage after installation.

OVERVIEW

Key Components:

• Fixing Lugs: These are used to securely connect the manifold to a fixing point inside the wall cavity.
• Manifold: The main body of the mixer.
• Single Lever Ceramic Disc Cartridge: The component responsible for controlling the water flow and temperature.
• Flange: A component used in the assembly process.
• Wall Plate: Another component used in the assembly process.
• Spout: The part through which the water flows.
• Grub Screws: These are located on the underside of the spout and used to secure it in place.
• Handle: The operating handle(s) used to control the mixer.

PRODUCT SHOWN WILL VARY DEPENDING ON MODEL

Guarantee & Aftercare

When installing or using tools, extra care must be taken to avoid damaging the finish or fitting. To maintain the appearance, please ensure it is cleaned regularly using a clean soft damp cloth only. Abrasive cleaners or detergents must not be used as they may cause surface deterioration. The company provides a guarantee against faulty material or manufacture excluding serviceable parts, providing they have been installed, cared for and used in accordance with our instructions.

Water Supply Regulations

This product has been manufactured to comply with the appropriate BS EN Standards and to conform to Water Supply Regulations 1999.

Earth Bonding

• Earth any new pipework satisfactorily (Seek expert advice if in doubt).
• The company reserves the right to continually evolve its product lines without notification.
• The company will not accept any liability regarding specification changes and their consequences unless previously quoted by the company in writing.

Installation Procedure

1. Prior to installation please ensure all the supply pipes have been flushed through to remove any debris and then ensure the water supply is turned off.
2. We strongly recommend the fitting of service isolation valves to the inlet feeds for ease of future maintenance.
3. Ensure you have all the relevant tools before commencing the installation and take note of any specific markings on the product to make sure they are installed correctly.
4. Create a wall opening suitable for the manifold body, making sure the opening is big enough to allow for ease of maintenance.
5. Securely connect the manifold to a suitable fixing point inside the wall cavity using the fixing lugs. NB please make use you use appropriate fixings for these connection points (Not supplied).
6. Connect the water supplies as indicated on the manifold body.
7. Check all water feed connections to ensure there are no leaks.
8. Assemble the flanges/wall plate and apply a small bead of silicone around these to create a water tight seal around the cover plate(s)
9. Connect the spout and secure in place using the underside grub screws for a secure connection.
10. Fit the operating handle(s)
11. Check the assembled fit of the products to ensure there is no water ingress that may cause water damage after installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>